23.020.10 固定容器和罐 标准查询与下载
共找到 597 条与 固定容器和罐 相关的标准，共 40 页
"Calculation of tanks and apparatus made of thermoplastics - Vertical round, non-pressurised tanks - Parallel-supported sloping base"
- ICS
- 23.020.10
- CCS
- 发布
- 2012-01
- 实施
Calculation of tanks and apparatus made of thermoplastics - Vertical round non-pressurised tanks - Example of a parallel-supported sloping base
- ICS
- 23.020.10
- CCS
- 发布
- 2012-01
- 实施
Calculation of tanks and apparatus made of thermoplastics - Vertical round non-pressurised tanks - Ring-supported conical bottom
- ICS
- 23.020.10
- CCS
- 发布
- 2012-01
- 实施
Calculation of tanks and equipment made of thermoplastics Vertical, round, atmospheric tanks Flat-bottomed tanks in seismic zones
- ICS
- 23.020.10
- CCS
- 发布
- 2012-01
- 实施
Calculation of storage tanks and equipment made of thermoplastics Vertical round non-pressurized storage tanks Vertical frame storage tanks in seismic zones
- ICS
- 23.020.10
- CCS
- 发布
- 2012-01
- 实施
Calculation of tanks and apparatus made of thermoplastics - Vertical round non-pressurised tanks - Example of a ring-supported conical bottom
- ICS
- 23.020.10
- CCS
- 发布
- 2012-01
- 实施
Standard for Safety for Nonmetallic Safety Cans for Petroleum Products
- ICS
- 23.020.10
- CCS
- E98
- 发布
- 2012
- 实施
1.1 This specification provides design, construction, and purchasing criteria for docking/drain plug and boss assemblies. 1.2 Assemblies are intended for installation in shell, rudder, and tank bottom plate from 8 through 38 mm. 1.3 Assemblies shall be installed at the lowest point of a tank or rudder for draining during dry docking. 1.4 The values stated in SI units are to be regarded as the standard.
Standard Specification for Docking/Drain Plug and Boss Assemblies [Metric]
- ICS
- 23.020.10
- CCS
- 发布
- 2012
- 实施
This standard describes the design, fabrication, installation, inspection, and testing of bolted aboveground thermoset fiberglass-reinforced plastic (FRP) panel-type tanks for potable water. Requirements for the fabrication, handling, construction, and testing of FRP panels, concrete and steel foundation structure, foundation, and accessories are included.
Bolted Aboveground Thermosetting Fiberglass-Reinforced Plastic Panel-Type Tanks for Water Storage
- ICS
- 23.020.10
- CCS
- Q81
- 发布
- 2012
- 实施
本标准规定了碳素钢和低合金钢制球形储罐定期检验的术语与定义、基本条件、检验前的准备、检验实施、检验结果评价。 注1：以下球罐均指碳素钢和低合金钢制球形储罐。 本标准适用于设计压力大于等于0.1MPa，且小于等于4MPa的桔瓣式或混合式以支柱支撑的属于压力容器范围内的球罐。 本标准适用的设计温度范围按钢材允许的使用温度确定。 本标准不适用于下列球罐： a) 受核辐射的球罐； b) 经受相对运动（如车载或船载）的球罐； c) 公称容积小于50m3的球罐； d) 要求做疲劳分析的球罐； e) 双壳结构的球罐；
Specification for periodic inspection of steel spherical storage tanks
- ICS
- 23.020.10
- CCS
- J 74
- 发布
- 2011-12-25
- 实施
- 2012-03-31
Calculation of tanks and apparatus made of thermoplastics - Welding factors
- ICS
- 23.020.10
- CCS
- 发布
- 2011-11
- 实施
This document specifies the requirements for metallic shop fabricated cylindrical, horizontal steel tanks, single and double skin for the aboveground storage of water polluting liquids (both flammable and non-flammable) within the following limits: - from 800 mm up to 3 000 mm nominal diameter and, - up to a maximum overall length of 6 times the nominal diameter and, - for liquids with a maximum density of up to 1,9 kg/l and, - with an operating pressure (Po) of maximum 1,5 bar (abs.) and, - where double skin tanks with a vacuum leak detection system are used the cinematic viscosity of the stored media shall not exceed 5 ´ 10-3 m2/s. This document is applicable for normal ambient temperature conditions (- 20 °C to + 50 °C). Where temperatures are outside this range, additional requirements need to be taken into account. This document is not applicable for the storage of liquids having dangerous good classes listed in Table 1 because of the special dangers involved. Table 1 - List of dangerous goods the storage of which are not covered by this document UN-classification Storage media Class 1 Explosives Class 4.2 Substances liable to spontaneous combustion Class 4.3 Substances which in contact with water emit flammable gases Class 5.2 Organic peroxides Class 6.2 Infectious substances Class 7 Radioactive material, hydrocyanic or hydrocyanic solvent liquids, metalcarbonyls, hydrofluoracid, bromide liquids NOTE The classifications referred to are those adopted by the United Nations Committee of Experts on the Transport of Dangerous Goods (not to be interpreted as tank classes described in 3.1.4). This document does not cover the installation of tanks which might be subject to local regulations involving pollution control.
Workshop fabricated steel tanks - Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids
- ICS
- 23.020.10
- CCS
- 发布
- 2011-10-12
- 实施
This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without Thermoplastics lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised up to 10 bar, for use above ground.The terms vessels and tanks as used in this European Standard include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell. In addition to the definitive requirements, this European Standard also requires the items in Clause 5 to be fully documented.This Europe
GRP tanks and vessels for use above ground - Part 3: Design and workmanship
- ICS
- 23.020.10
- CCS
- 发布
- 2011-08-30
- 实施
- 2011-08-30
GRP tanks and vessels for use above ground - Part 3: Design and workmanship
- ICS
- 23.020.10
- CCS
- 发布
- 2011-05-31
- 实施
- 2011-05-31
Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements an
- ICS
- 23.020.10
- CCS
- 发布
- 2011-04-29
- 实施
- 2011-04-29
Calculation of tanks and apparatus made of thermoplastics - Characteristic values of the polypropylene material group
- ICS
- 23.020.10
- CCS
- 发布
- 2011-04
- 实施
"Calculation of tanks and apparatus made of thermoplastics - Vertical round, non-pressurised tanks - Parallel-supported sloping base"
- ICS
- 23.020.10
- CCS
- 发布
- 2011-04
- 实施
Calculation of tanks and apparatus made of thermoplastics - Reduction coefficients in the case of a media influence
- ICS
- 23.020.10
- CCS
- 发布
- 2011-04
- 实施
Calculation of tanks and apparatus made of thermoplastics - Characteristic values
- ICS
- 23.020.10
- CCS
- 发布
- 2011-04
- 实施
This document specifies requirements for materials, physical properties and performance of single blow mouled and rotationally moulded polyethylene tanks and of rotationally mouled tanks made of anionically polymerized polyamide 6, with or without reinforcements, for above ground storage of domestic heating oil, kerosene and diesel fuels for the supply of building heating/cooling systems.
Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements an
- ICS
- 23.020.10
- CCS
- E98
- 发布
- 2011-04
- 实施
- 2011-04-01
