23.020.40 低温容器 标准查询与下载
共找到 335 条与 低温容器 相关的标准，共 23 页
本标准规定了低温绝热压力容器漏率试验的原理、仪器设备、试验条件、试验程序、数据处理。 本标准适用于真空绝热型低温绝热压力容器漏率的测量。
Testing method of cryo-insulation pressure vessels leakage measurement
- ICS
- 23.020.40
- CCS
- J76
- 发布
- 2001-09-03
- 实施
- 2002-04-01
BS EN ISO 21028-1 Cryogenic vessels - Toughness requirements for materials at cryogenic temperature - Part 1: Temperatures below -80 degrees C
- ICS
- 23.020.40
- CCS
- 发布
- 2024-03-25
- 实施
- 2024-03-25
BS ISO 21013-2 Cryogenic vessels - Pressure-relief accessories for cryogenic service - Part 2: Non-reclosable pressure-relief devices
- ICS
- 23.020.40
- CCS
- 发布
- 2024-02-27
- 实施
- 2024-02-27
本文件规定了迷你型深冷液体低温储罐的产品结构、主要参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于迷你型深冷液体低温储罐的生产和检验。
Mini cryogenic liquid cryogenic storage tank
- ICS
- 23.020.40
- CCS
- C348
- 发布
- 2024-01-16
- 实施
- 2024-01-31
一、技术基础 二、产品组成和分类 三、产品功效 四、性能指标 五、分类 六、要求
Food container for liquid with built-in sterile bag
- ICS
- 23.020.40
- CCS
- C292
- 发布
- 2024-01-02
- 实施
- 2024-01-30
Cryogenic vessels — Pumps for cryogenic service
- ICS
- 23.020.40
- CCS
- 发布
- 2023-09
- 实施
BS ISO 21013-1 AMD 1. Cryogenic vessels. Pressure-relief accessories for cryogenic service - Part 1. Reclosable pressure-relief valves
- ICS
- 23.020.40
- CCS
- 发布
- 2023-06-07
- 实施
- 2023-06-07
本文件规定了固定式真空绝热深冷压力容器（以下简称“深冷容器”）的材料、设计、制造、检验与试验、标志与标识、出厂文件、贮存、涂敷与运输包装的基本要求。 注1：罐体的界定范围如下： a)罐体与外部管路焊接连接的第一道环向接头的坡口端面，螺纹连接的第一个螺纹接头端面，法兰连接的第一个法兰密封面； b)罐体开孔部分的端盖及其紧固件； c)罐体与非受压元件的连接焊缝。 注2：管路包括所有深冷容器自带的可能与深冷介质接触的管子与管件。 注3：主要受压元件包括内容器筒体、内容器封头以及与介质接触的管座、凸缘、工艺人孔筒体、工艺人孔封头等。
Static vacuum powder insulated cryogenic pressure vessels
- ICS
- 23.020.40
- CCS
- C344
- 发布
- 2023-05-06
- 实施
- 2023-05-06
Cryogenic vessels — Static vacuum insulated vessels — Part 2: Operational requirements
- ICS
- 23.020.40
- CCS
- 发布
- 2023-04
- 实施
1 Scope This document specifies requirements for the design, fabrication, inspection and testing of static vacuum-insulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar. This document applies to static vacuum-insulated cryogenic vessels for fluids and does not apply to vessels designed for toxic fluids. This document also gives guidance for static vacuum-insulated cryogenic vessels designed for a maximum allowable pressure of not more than 0,5 bar.
Cryogenic vessels — Static vacuum-insulated vessels - Part 1: Design, fabrication, inspection and tests
- ICS
- 23.020.40
- CCS
- 发布
- 2022-10-31
- 实施
- 2022-10-31
1 Scope This document defines practical methods for determining the heat-leak performance of cryogenic vessels. The methods include measurement on both open and closed systems . This document neither specifies the requirement levels for insulation performance nor when the defined methods are applied.
Cryogenic vessels. Cryogenic insulation performance
- ICS
- 23.020.40
- CCS
- 发布
- 2022-09-30
- 实施
- 2022-09-30
Cryogenic vessels — Cryogenic insulation performance — Amendment 1
- ICS
- 23.020.40
- CCS
- 发布
- 2022-08-29
- 实施
This document specifies requirements for the design, fabrication, inspection and testing of static vacuum-insulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar. This document applies to static vacuum-insulated cryogenic vessels for fluids and does not apply to vessels designed for toxic fluids. This document also gives guidance for static vacuum-insulated cryogenic vessels designed for a maximum allowable pressure of not more than 0,5 bar.
Cryogenic vessels — Static vacuum-insulated vessels — Part 1: Design, fabrication, inspection and tests
- ICS
- 23.020.40
- CCS
- 发布
- 2022-08-18
- 实施
1 Scope This document specifies requirements for the design, fabrication, inspection and testing of large transportable vacuum-insulated cryogenic vessels of more than 450 l volume, which are permanently ( fixed tanks ) or not permanently ( demountable tanks and portable tanks ) attached to a means of transport, for one or more modes of transport. This document applies to large transportable vacuum-insulated cryogenic vessels for fluids specified in 3.1 and does not apply to vessels designed for toxic fluids. This document does not include the general vehicle requirements, e.g. running gear, brakes, lighting, etc. NOTE 1 This document does not cover specific requirements for refillable liquid-hydrogen tanks that are primarily dedicated as fuel tanks in vehicles. For fuel tanks used in land vehicles, see ISO 13985. NOTE 2 This document does not cover specific requirements for refillable liquid hydrogen and LNG tanks that are primarily dedicated as fuel tanks in vehicles. For fuel tanks used in vehicles, see ISO 13985.
Cryogenic vessels. Large transportable vacuum-insulated vessels - Design, fabrication, inspection and testing
- ICS
- 23.020.40
- CCS
- 发布
- 2022-06-30
- 实施
- 2022-06-30
本文件规定了低温乙烯装置用桶袋泵技术规范的术语和定义、技术要求、基本设计、试验方法、检验规则、标志、包装、运输和贮存、质量保证。 本文件适用于设计、制造、材料、检验、测试、装运、资料交付和质量保证的最低要求。
Technical specification for bag pump for low temperature ethylene plant
- ICS
- 23.020.40
- CCS
- C339
- 发布
- 2022-06-10
- 实施
- 2022-06-29
Cryogenic vessels－Toughness requirements for material at cryogenic temperature－Part 1：Temperatures below－80 ℃
- ICS
- 23.020.40
- CCS
- 发布
- 20220602
- 实施
- 20220602
Cryogenic vessels－Static vacuum insulated vessels－Part 2：Operational requirements
- ICS
- 23.020.40
- CCS
- 发布
- 20220602
- 实施
- 20220602
Cryogenic vessels — Transportable vacuum insulated vessels of not more than 1 000 litres volume — Part 2: Operational requirements
- ICS
- 23.020.40
- CCS
- 发布
- 20220602
- 实施
- 20220602
Cryogenic vessels－Pumps for cryogenic service
- ICS
- 23.020.40
- CCS
- 发布
- 20220602
- 实施
- 20220602
Cryogenic vessels — Large transportable vacuum-insulated vessels — Part 1: Design, fabrication, inspection and testing — Amendment 1
- ICS
- 23.020.40
- CCS
- 发布
- 2022-04-12
- 实施
