23.040.10 铁管和钢管 标准查询与下载

ASTM A691/A691M-18a 高温高压用电熔焊碳和合金钢管的标准规范

Standard Specification for Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures

ASTM A1098/A1098M-18 带纹理表面的焊接奥氏体、铁素体、马氏体和双相不锈钢锅炉、过热器、冷凝器和热交换器管的标准规范

Standard Specification for Welded Austenitic, Ferritic, Martensitic and Duplex Stainless Steel Boiler, Superheater, Condenser, and Heat Exchanger Tubes with Textured Surface(s)

ASTM A134/A134M-18 电熔（电弧）焊接钢管（尺寸大于等于NPS 16）的标准规范

Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)

T/CWHIDA 002-2018 水利水电工程球墨铸铁管道技术导则

为规范水利水电工程球墨铸铁管道的设计、施工及验收，满足工程安全、经济合理、技术先进的要求，特制定本标准。本标准适用的球墨铸铁管道，公称直径范围为DN80～DN2600，流体温度为0℃～50℃。球墨铸铁管道的设计、施工及验收除应符合本标准外，尚应符合国家现行有关标准的规定。

Technical Guidelines for Ductile Iron Pipelines in Water Conservancy and Hydropower Projects

ASTM A513/A513M-18 电阻焊接碳钢和合金钢机械管标准规范

Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing

ASTM A530/A530M-18 专用碳钢和合金钢管的一般要求标准规范

1.1 This specification2 covers a group of requirements which, with the exceptions of Section 6.3, Section 14, Section 21, and Section 22, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification specifies different requirements, in which case the requirement of the product specification shall prevail. 1.2 Sections 6.3 or 21 are mandatory if the product specification has a requirement for product analysis or flattening tests. 1.3 Section 22 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters. 1.4 Section 14 is for information only. 1.5 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification, only the requirement of the product specification need be satisfied. Title of Specification ASTM DesignationA Seamless Carbon Steel Pipe for High-Temperature Service A106/A106M Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission Systems A381 Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures A524 Centrifugally Cast Carbon Steel Pipe for High-Temperature Service A660/A660M Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures A671/A671M Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures A672/A672M Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures A691/A691M A These designations refer to the latest issue of the respective specifications. 1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order. NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe

ASTM A589/A589M-06(2018) 无缝和焊接碳钢水井管道标准规范

1.1 This specification covers four specific types of plain end or threaded and coupled carbon steel pipe for use in water wells. 1.2 Each type of water well pipe shall conform to the following methods of manufacture and grade as specified on the purchase order: 1.2.1 Type I, Drive Pipe—Seamless or electric-resistancewelded, Grades A and B. 1.2.2 Type II, Water-Well Reamed and Drifted Pipe— Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.2.3 Type III, Driven Well Pipe—Seamless or electricresistance-welded, Grades A and B, or furnace-butt welded. 1.2.4 Type IV, Water-Well Casing Pipe—Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.3 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values in each system are not exact equivalents; therefore, each system is to be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. NOTE 1—The dimensionless designator NPS (nominal pipe size) and DN (Nominal Diameter) have been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Carbon Steel Water-Well Pipe

ASTM A450/A450M-18 碳和低合金钢管一般要求的标准规范

Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes

ASTM A688/A688M-18 无缝和焊接奥氏体不锈钢给水加热管标准规范

Standard Specification for Seamless and Welded Austenitic Stainless Steel Feedwater Heater Tubes

ASTM A1065/A1065M-18 冷成型电熔（电弧）焊接高强度低合金标准规范；最小屈服点为50 ksi[345 MPa]的合金结构管

1.1 This specification covers three Types and two Grades of cold formed electric-fusion (arc) welded high-strength lowalloy steel tubing of 50 ksi [345 MPa] minimum yield point for use in welded or bolted construction of buildings and for general structural purposes. 1.2 This tubing is produced in square and rectangular sizes with a periphery of 200 in. [500 cm] or less and a specified wall thickness of 1.00 in. [25 mm] or less. Tubes are joined by two longitudinal electric-fusion (arc) welds. Circumferential welds are disallowed. Sizes outside of those listed in Tables 4 and 5 may be ordered provided all other requirements of the specification are met. Typical lengths are 15 to 50 ft [5 to 15 m]. NOTE 1—Products manufactured to this specification may not be suitable for those applications such as dynamically loaded elements in welded structures, etc. where low-temperature toughness properties may be important. (See Supplementary Requirement S1.) 1.3 This specification covers the following Types: 1.3.1 Type 1—Welded with backing, backing left in the product, 1.3.2 Type 2—Welded with backing, backing removed, 1.3.3 Type 3—Welded without backing. 1.4 Tubing is available in Grades 50 [345] and 50W [345W]. Grade 50 [345] is manufactured from high-strength low-alloy steel. Grade 50W [345W] is manufactured from high-strength low-alloy steel with enhanced atmospheric corrosion resistance. (See 10.1.2) The Grades may not be interchanged without approval of the purchaser. ASTM Specifications for plate that may be applied to Grade 50 [345] and 50W [345W] are listed in Reference Documents and in Table 1. 1.5 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cold-Formed Electric-Fusion (Arc) Welded High-Strength Low–Alloy Structural Tubing in Shapes, with 50 ksi [345 MPa] Minimum Yield Point

ASTM A335/A335M-18a 无缝铁素体合金钢管高温服务标准规范

Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

ASTM A252-10(2018) 焊接和无缝钢管桩的标准规范

Standard Specification for Welded and Seamless Steel Pipe Piles

ASTM A214/A214M-96(2018) 电阻焊碳钢热交换器和冷凝器管的标准规范

Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes

ASTM A556/A556M-18 无缝冷拔碳钢给水加热管标准规范

1.1 This specification2 covers minimum-wall-thickness, seamless cold-drawn carbon steel tubes including bending into the form of U-tubes, if specified, for use in tubular feedwater heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 11⁄4-in. [15.9 to 31.8-mm] outside diameter, inclusive, with minimum wall thicknesses equal to or greater than 0.045 in. [1.1 mm]. 1.3 Optional supplementary requirements are provided, and when desired, shall be stated in the order. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes

ASTM A312/A312M-18 无缝、焊接和重冷加工奥氏体不锈钢管的标准规范

Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

ASTM A213/A213M-18a 无缝铁素体和奥氏体合金 - 钢锅炉 过热器和热交换器管的标准规范

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

ASTM A512-18 冷拔对焊碳素钢机械管材的标准规范

1.1 This specification covers cold-drawn buttweld carbon steel tubes for use as mechanical tubing. 1.2 This specification covers round, square, rectangular, and special shape mechanical tubing. 1.3 Round tube size ranges covered are outside diameters up to 3 1⁄2 in. (88.9 mm) and wall thickness from 0.035 to 0.500 in. (0.89 to 12.70 mm). 1.4 Optional supplementary requirements are provided and, when desired, shall be so stated in the order. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This product is available in various grades (Section 6 Tables 1 and 2 and conditions (Section 5). 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cold-Drawn Buttweld Carbon Steel Mechanical Tubing

DIN EN ISO 3183:2018 石油和天然气工业.管道运输系统用钢管(ISO 3183-2012+Amd 1-2017); 德文版本EN ISO 3183-2012+A1-2018

This document specifies requirements for seamless and welded steel pipes of two product specification levels (PSL 1 and PSL 2) for use in pipeline transportation systems in the petroleum and natural gas industries

Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2012 + Amd 1:2017); German version EN ISO 3183:2012 + A1:2018

ASTM A249/A249M-18 焊接奥氏体钢锅炉、过热器、热交换器和冷凝器管的标准规范

Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes

T/CFA 02010202.3-2018 球墨铸铁给水排水管道工程施工及验收规范技术条件

管、管件和附件吊装、运输及储存要求 沟槽开挖要求 沟槽地基处理要求 开槽管道施工和安装要求 沟槽回填要求 非开挖管道施工安装要求 特殊条件下球墨铸铁管的施工安装要求 管道功能性试验 工程验收

The code for construction and acceptance of water and sewerage ductile iron pipeline works Specification requirement