23.040.10 铁管和钢管 标准查询与下载

ASTM A513/A513M-20 电阻焊接碳钢和合金钢机械管标准规范

Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing

ASTM A760/A760M-15(2020) 波纹钢管标准规格 金属涂层用于下水道和排水管

1.1 This specification covers corrugated steel pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. The steel sheet used in fabrication of the pipe has a protective metallic coating of zinc (galvanizing), aluminum, 55 % aluminum-zinc alloy, or zinc-5 % aluminummischmetal alloy. 1.2 The several different metallic coatings may not provide equal protection of the base metal against corrosion or abrasion in all environments, or both. Some environments may be so severe that none of the metallic coatings included in this specification will provide adequate protection. Additional protection for corrugated steel pipe can be provided by use of coatings applied after fabrication of the pipe as described in Specification A849, or by use of polymer precoated corrugated steel pipe as described in Specification A762/A762M. 1.3 Section 9 is intended to be applied to corrugated steel pipe joints. The several different types of corrugated steel pipe joints provide various qualities. This specification is not intended for routine quality control testing or in-field acceptance testing, but is intended to establish performance limits of the pipe joints, as well as the test requirements and test methods for the joints as described herein. 1.4 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheet thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The installation procedure is described in Practice A798/A798M. 1.5 This specification is applicable to orders in either inch-pound units as A760 or in SI units as A760M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the material is ordered to A760M. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains

ASTM A608/A608M-20 用于高温压力应用的离心铸铁 - 镍 - 镍高合金管的标准规范

1.1 This specification covers iron-chromium-nickel, highalloy tubes made by the centrifugal casting process intended for use under pressure at high temperatures. 1.2 The grades of high alloys detailed in Table 1 are intended for applications requiring strength and resistance to corrosion and scaling at high temperatures. 1.3 Optional Supplementary Requirements S1 to S11 are provided; these call for additional tests to be made if desired. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4.1 Within the text, the SI units are shown in brackets. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperatures

ASTM A1076/A1076M-20 由金属预涂钢板制成的冷成型碳素结构钢管标准规范

1.1 This specification covers round, square, rectangular, and special shape, electric-resistance-welded structural tubing produced from precoated sheet steel with the following coatings on both sides: zinc (galvanized) or 55% aluminum-zinc alloy or zinc-5 % aluminum alloy-coated. This product is intended for applications requiring minimum mechanical properties and corrosion resistance of both exterior and interior surfaces. 1.2 This specification covers: 1.2.1 Three grades of round tubing and three grades of shaped tubing, identified in Table 1 (Chemical Requirements), Table 2 (Mechanical Requirements of Round Structural Tubing), and Table 3 (Mechanical Requirements of Shaped Structural Tubing). 1.2.2 Three different types of coating composition/ designations (Section 7). 1.3 This specification is applicable to orders in either inch-pound units (as A1076) or SI units (as A1076M). Within the text, SI units are shown in brackets. The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cold Formed Carbon Structural Steel Tubing Made from Metallic Precoated Sheet Steel

ASTM C1277-20 连接无毂铸铁污水管和配件的屏蔽管接头的标准规范

1.1 This specification covers the materials and testing of shielded hubless couplings to join hubless cast iron soil pipe and fittings. 1.2 Several different types of hubless couplings are available for use in hubless cast iron sanitary and storm drain, waste, and vent piping applications to connect hubless cast iron soil pipe and fittings by using a sleeve-type, or some other type coupling device. It is the purpose of this specification to furnish information as to the characteristics of one such sleeve-type couplings when applied to cast iron soil pipe and fittings manufactured in accordance with Specification A888, latest revision, and CISPI 301, latest revision. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The committee with jurisdiction over this standard is aware of other comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 310, FM 1680 published by Factory Mutual, and Specification C1540 published by ASTM. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

ASME B16.39-2019 可锻铁螺纹管接头

This Standard covers threaded malleable iron unions, Classes 150, 250, and 300. It also contains provisions for using steel for NPS 1∕8 unions. This Standard includes (a) design (b) pressure–temperature ratings (c) size (d) marking (e) materials (f) joints and seats (g) threads (h) hydrostatic strength (i) tensile strength (j) air pressure test (k) sampling (l) coatings (m) dimensions 本标准涵盖螺纹可锻铸铁接头，等级 150、250 和 300。它还包含将钢材用于NPS 1∕8工会的规定。本标准包括 （a） 外观设计 （b） 压力-温度额定值 （c） 尺寸 （d） 标记 （e） 材料 （f） 关节和座椅 （g） 螺纹 （h） 静水强度 （一）抗拉强度 （j） 气压试验 （k） 抽样 （l） 涂料 （m） 尺寸

Malleable Iron Threaded Pipe Unions

ASTM A790/A790M-20 无缝和焊接铁素体/奥氏体不锈钢管的标准规范

Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe

ASTM A268/A268M-20 一般用途无缝和焊接铁素体和马氏体不锈钢管的标准规范

Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service

ASTM A671/A671M-20 用于大气和低温的电熔钢管的标准规范

1.1 This specification2 covers electric-fusion-welded steel pipe with filler metal added, fabricated from pressure vessel quality plate of several analyses and strength levels and suitable for high-pressure service at atmospheric and lower temperatures. Heat treatment may or may not be required to attain the desired properties or to comply with applicable code requirements. Supplementary requirements are provided for use when additional testing or examination is desired. 1.2 The specification nominally covers pipe 16 in. [400 mm] in outside diameter or larger and of 1⁄4 in. [6 mm] wall thickness or greater. Pipe having other dimensions may be furnished provided it complies with all other requirements of this specification. 1.3 Several grades and classes of pipe are provided. 1.3.1 Grade designates the type of plate used as listed in 5.1. 1.3.2 Class designates the type of heat treatment performed during manufacture of the pipe, whether the weld is radiographically examined, and whether the pipe has been pressure tested as listed in 1.3.3. 1.3.3 Class designations are as follows (Note 1): Class Heat Treatment on Pipe Radiography, see Section Pressure Test, see: 10 none none none 11 none 9 none 12 none 9 8.3 13 none none 8.3 20 stress relieved, see 5.3.1 none none 21 stress relieved, see 5.3.1 9 none 22 stress relieved, see 5.3.1 9 8.3 23 stress relieved, see 5.3.1 none 8.3 30 normalized, see 5.3.2 none none 31 normalized, see 5.3.2 9 none 32 normalized, see 5.3.2 9 8.3 33 normalized, see 5.3.2 none 8.3 40 normalized and tempered, see 5.3.3 none none 41 normalized and tempered, see 5.3.3 9 none 42 normalized and tempered, see 5.3.3 9 8.3 43 normalized and tempered, see 5.3.3 none 8.3 50 quenched and tempered, see 5.3.4 none none 51 quenched and tempered, see 5.3.4 9 none 52 quenched and tempered, see 5.3.4 9 8.3 53 quenched and tempered, see 5.3.4 none 8.3 70 quenched and precipitation heat treated none none 71 quenched and precipitation heat treated 9 none 72 quenched and precipitation heat treated 9 8.3 73 quenched and precipitation heat treated none 8.3 NOTE 1—Selection of materials should be made with attention to temperature of service. For such guidance, Specification A20/A20M may be consulted. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures

ASTM A523/A523M-20 高压管式电缆线路用平端无缝和电阻焊接钢管的标准规范

Standard Specification for Plain End Seamless and Electric-Resistance-Welded Steel Pipe for High-Pressure Pipe-Type Cable Circuits

ASTM A795/A795M-13(2020) 防火用黑色和热浸镀锌（镀锌）焊接无缝钢管的标准规范

Standard Specification for Black and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless Steel Pipe for Fire Protection Use

JG/T 225-2020 预应力混凝土用金属波纹管

　　现批准《预应力混凝土用金属波纹管》为建筑工业行业产品标准，编号为JG/T225-2020，自2020年8月1日起实施。原《预应力混凝土用金属波纹管》（JG/T225-2007）同时废止。 　　本标准在住房和城乡建设部门户网站（www.mohurd.gov.cn）公开，并由住房和城乡建设部标准定额研究所组织中国质量标准出版传媒有限公司出版发行。 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　中华人民共和国住房和城乡建设部 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　2020年1月13日

Metal corrugated pipes for prestressed concrete

ASTM E213-20 金属管超声波检验的标准实施规程

1.1 This practice2 covers a procedure for detecting discontinuities in metal pipe and tubing during a volumetric examination using ultrasonic methods. Specific techniques of the ultrasonic method to which this practice applies include pulse-reflection techniques, both contact and non-contact (for example, as described in Guide E1774 and Practice E1816), and angle beam immersion techniques, both conventional and phased array. Artificial reflectors consisting of longitudinal, and, when specified by the using party or parties, transverse reference notches placed on the surfaces of a reference standard are employed as the primary means of standardizing the ultrasonic system. 1.2 This practice is intended for use with tubular products having outside diameters approximately 1⁄2 in. (12.7 mm) and larger, provided that the examination parameters comply with and satisfy the requirements of Section 12. These procedures have been successful with smaller sizes. These may be specified upon contractual agreement between the using parties. These procedures are intended to ensure that proper beam angles and beam shapes are used to provide full volume coverage of pipes and tubes, including those with low ratios of outside diameter-to-wall thickness, and to avoid spurious signal responses when examining small-diameter, thin-wall tubes. 1.3 The procedure in Annex A1 is applicable to pipe and tubing used in nuclear and other special and safety applications. The procedure in Annex A2 may be used to determine the helical scan pitch. 1.4 This practice does not establish acceptance criteria; they must be specified by the using party or parties. 1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Ultrasonic Examination of Metal Pipe and Tubing

NB/T 10370-2019 煤矿抽放瓦斯用焊接不锈钢管吸能检验规范

Specifications for energy absorption inspection of welded stainless steel pipes used for gas drainage in coal mines

ASTM A213/A213M-19a 无缝铁素体和奥氏体合金 - 钢锅炉 过热器和热交换器管的标准规范

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

EN 14901-2:2019 球墨铸铁管、管件和附件 球墨铸铁管件和附件有机涂层的要求和试验方法 第2部分：热塑性酸改性聚烯烃涂层（TMPO）

This document defines the requirements and test methods for factory applied thermoplastic acid modified polyolefin (TMPO) coatings used for the protection of ductile iron fittings and accessories according to EN 545, EN 598, EN 969, EN 12842 and EN 14525: - conveying water (e.g. potable water, raw water, …) at operating temperature up to 50 °C; or - conveying waste water at operating temperature up to 45 °C; or - conveying gas at operating temperature up to 50 °C; - suitable for external environments, i.e. soils, waters and atmospheres of all common corrosion loads, characterized in D.2.3 of EN 545:2010.

Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 2: Thermoplastic acid modified polyolefin coating (TMPO)

EN 14901-1:2014+A1:2019 球墨铸铁管、管件和附件 球墨铸铁管件和附件有机涂层的要求和试验方法 第1部分：环氧涂层（重型）

This European Standard defines the requirements and test methods for factory applied epoxy coatings (fusion bonded powder or liquid two-pack) used for the corrosion protection of ductile iron fittings and accessories conforming to EN 545, EN 598, EN 969, EN 12842, EN 14525, for: - conveying water (e.g. potable water) at operating temperature up to 50 °C excluding frost; or - conveying waste water at operating temperature up to 45 °C excluding frost; or - conveying gas at operating temperature up to 50 °C; - suitable for external environments, i.e. soils, waters and atmospheres of all common corrosion loads, characterized in EN 545:2010, D.2.3.

Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty)

ASTM A106/A106M-19a 高温用无缝碳钢管标准规范

1.1 This specification2 covers seamless carbon steel pipe for high-temperature service (Note 1) in NPS 1⁄8 to NPS 48 [DN 6 to DN 1200] (Note 2) inclusive, with nominal (average) wall thickness as given in ASME B 36.10M. It shall be permissible to furnish pipe having other dimensions provided such pipe complies with all other requirements of this specification. Pipe ordered under this specification shall be suitable for bending, flanging, and similar forming operations, and for welding. When the steel is to be welded, it is presupposed that a welding procedure suitable to the grade of steel and intended use or service will be utilized. NOTE 1—It is suggested, consideration be given to possible graphitization. NOTE 2—The dimensionless designator NPS (nominal pipe size) [DN (diameter nominal)] has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.2 Supplementary requirements of an optional nature are provided for seamless pipe intended for use in applications where a superior grade of pipe is required. These supplementary requirements call for additional tests to be made and when desired shall be so stated in the order. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following precautionary caveat pertains only to the test method portion, Sections 11, 12, and 13 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service

ASTM A376/A376M-19 高温用无缝奥氏体钢管的标准规范

Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Service

ASTM A213/A213M-19 无缝铁素体和奥氏体合金 - 钢锅炉 过热器和热交换器管的标准规范

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes