23.060.30 闸阀 标准查询与下载

BS EN 593:2010 工业阀门 金属蝶阀

Industrial valves. Metallic butterfly valves

GSO EN 1984:2009 工业阀门 钢制闸阀

This European standard specifies the requirements for steel gate valves which are wrought, cast or fabricated with end connections flanged, butt welding, socket welding or threaded. This standard is applicable to steel gate valves mainly used for industrial and general purpose applications. However they can be used for other applications provided the requirements of the relevant performance standards are met. The ranges of nominal sizes covered is: DN8; DN10; DN12; DN15; DN20; DN25; DN32; DN40; DN50; DN65; DN80; DN100; DN125; DN150; DN200; DN250; DN300; DN350; DN400; DN450; DN500; DN600; DN700; DN750; DN800; DN900; DN1000 DN750 is used for Class designated valves only. DN8 and DN12 are not used for flanged end connections. Socket welding end valves and threaded end valves are limited to the range DN8 to DN65. The range of pressure designations covered is: a) for flanged valves PN10; PN16; PN25; PN40; PN63; PN100 Class 150; Class 300; Class 600 b) for butt welding end valves PN10, PN16, PN25, PN40, PN63, PN100 Class 150, Class 300, Class 600 c) for socket welding end valves and threaded end valves PN10; PN16; PN25; PN40; PN63; PN100 Class 600; Class 800 The progress of work of the various standards referred to in the normative references can require revision of this standard NOTE 1 Socket welding end and threaded end valves are not normally manufactured with the pressure designations PN10, PN16, PN25 and PN40. NOTE 2 Class 800 is an intermediate class designation widely used for socket welding and threaded end valves.

Industrial valves - Steel gate valves

GSO EN 1171:2009 工业阀门 铸铁闸阀

This European Standard specifies the requirements for cast iron gate valves with flanged ends, socket ends or spigot ends. This standard is applicable to cast iron gate valves mainly used for industrial and general-purpose applications. However, they can be used for other applications provided the requirements of the relevant performance standards are met. The range of nominal sizes covered is: DN 40 ; DN 50 ; DN 65 ; DN 80 ; DN 100 ; DN 125 ; DN 150 ; DN 200 ; DN 250 ; DN 300 ; DN 350 ; DN 400 ; DN 450 ; DN 500 ; DN 600 ; DN 700 ; DN 800 ; DN 900 ; DN 1 000. The range of pressure designations covered is: ¾ isobaric PN 6; PN 10; PN 16; PN 25; ¾ isomorphic, PS 10 bar to PS 1 bar at room temperature.

Industrial valves - Cast iron gate valves

ASME B16.10-2009 阀门的面对面和点对点尺寸规格

This Standard covers face-to-face and end-to-end dimensions of straightway valves, and center-to-face and center-to-end dimensions of angle valves. Its purpose is to assure installation interchangeability for valves of a given material, type, size, rating class, and end connection.

Face-to-Face and End-to-End Dimensions of Valves

ANSI/AWWA C515-2009 供水设备用壁厚减小的弹性带座闸阀

This standard describes reduced-wall resilient-seated gate valves with non-rising stems (NRS) and outside screw-and-yoke (OS&Y) rising stems, including tapping gate valves, for water supply service having a temperature range of 33° to 125°F (0.6° to 52°C). These valves are intended for applications where fluid velocity does not exceed 16 ft/sec (4.9 m/sec) when the valve is in the full open position.

Reduced-Wall, Resilient-Seated Gate Valves for Water Supply Service

ANSI/ASSE 1063-2009 气阀和通气流入防护装置性能要求

The purpose of Air Valve and Vent Inflow Preventer Assemblies is to allow the release and admission of high volumes of air through air valves and air vents in water distribution systems but prevent the entry of contaminated water when the air valve outlet becomes submerged from flooding or is the target of malicious tampering.

Performance Requirements for Air Valve and Vent Inflow Preventer

SL 432-2008 水利工程压力钢管制造安装及验收规范

本标准规定了水利水电工程压力钢管、冲沙孔钢衬和泄水孔（洞）钢衬的制造、安装及验收的技术要求。 本标准适用于水利水电工程压力钢管、冲沙孔钢衬和泄水孔（洞）钢衬的制造、安装及验收。

Specification for manufacture and installation together with acceptance of steel penstocks which be served hydraulic engineering

DIN EN ISO 16139 Berichtigung 1:2008 工业阀门.热塑性塑料材料的闸阀.技术勘误DIN EN ISO 16139-2006

Industrial valves - Gate valves of thermoplastics materials (ISO 16139:2006); German version EN ISO 16139:2006, Corrigenda to DIN EN ISO 16139:2006-06

DIN EN ISO 16136 Berichtigung 1:2008 工业阀门.热塑性塑料材料的蝶形阀.技术勘误DIN EN ISO 16136-2006

Industrial valves - Butterfly valves of thermoplastics materials (ISO 16136:2006); German version EN ISO 16136:2006, Corrigenda to DIN EN ISO 16136:2006-06

KS V 7421-2007(2012) 船用青铜5K旋下止回阀（活接头阀盖式）

Marine bronze 5 K screw-down check globe valves(Union bonnet type)

KS V 7414-2007(2012) 阶梯船体青铜角阀

Marine hull bronze angle valves

KS V 7362-2007(2012) 海洋青铜5K的旋入式止回角阀

Marine bronze 5 K screw-down check angle valves

KS V 7381-2007(2012) 海洋青铜5K的旋启式止回阀

Marine bronze 5 K swing check valves

KS V 7389-2007(2012) 带咬合接头的船用黄铜30K截止阀

Marine brass 30 K stop valves with bite joint(s)

KS V 7420-2007(2012) 船用青铜16K旋入式止回角阀

Marine bronze 16 K screw-down check angle valves

KS V 7428-2007(2012) 海洋青铜联盟阀盖16 K型升降式止回阀角阀

Marine bronze 16 K lift check angle valves(Union bonnet type)

KS V 7378-2007(2022) 船用青铜10K升杆式闸阀

Marine bronze 10 K rising stem type gate valves

KS V 7398-2007(2012) 船用青铜阀门20开尔发光探针

Marine bronze 20 K globe valves

KS V 7377-2007 船用青铜5K上升式止回阀

이 규격은 선박용 청동 5 K 상승식 게이트 밸브에 대하여 규정한다.

Marine bronze 5 K rising stem type gate valves

KS V 7378-2007 船用青铜10K上升式闸阀

이 규격은 선박의 증가관 계통, 맑은 물 및 급수관 계통, 연료유 및 윤활유관 계통에 사용

Marine bronze 10 K rising stem type gate valves