23.100.01 流体动力系统综合 标准查询与下载

ISO 19973-2:2015 气压传动.通过测试评定元件的可靠度.第2部分:方向控制阀

This part of ISO 19973 provides test procedures for assessing the reliability of pneumatic directional control valves by testing and the methods of reporting the results of testing. General test conditions and the calculation method are provided in ISO 19973-1. The methods specified in ISO 19973-1 apply to the first failure, as obtained with the three-points moving average (3PMA) method, without repairs, but excluding outliers. The lifetime of pneumatic and electro-pneumatic directional control valves is usually given as a number of cycles. Therefore, whenever the term “time” is used in this part of ISO 19973, this variable is to be understood as cycles. This part of ISO 19973 also specifies test equipment and threshold levels for tests to assess the reliability of pneumatic directional control valves.

Pneumatic fluid power - Assessment of component reliability by testing - Part 2: Directional control valves

ISO 19973-3:2015 气压传动.通过测试评定元件的可靠度.第3部分:带活塞杆的气缸

This part of ISO 19973 provides test procedures for assessing the reliability of pneumatic cylinders with piston rod, both single-acting and double-acting, by testing and the methods of reporting the results of testing. General test conditions and the calculation method are provided in ISO 19973-1. The methods specified in ISO 19973-1 apply to the first failure, as obtained with the three-point moving average (3PMA) method, without repairs, but excluding outliers. The lifetime of pneumatic cylinders is usually given in number of cycles or in kilometres. Therefore, whenever the term “time” is used in this part of ISO 19973, this variable is to be understood as cycles or kilometres. This part of ISO 19973 also specifies test equipment and threshold levels for tests to assess the reliability of pneumatic cylinders with piston rods. This part of ISO 19973 is intended to be applied to pneumatic piston rod cylinders that conform to conform to these International Standards but are used in the same range of operating conditions can be tested in accordance with one of the classes defined in Tables 1 and 2.

Pneumatic fluid power - Assessment of component reliability by testing - Part 3: Cylinders with piston rod

ISO 19973-5:2015 气压液动. 通过试验评估部件的可靠性. 第5部分: 非回流阀, 梭阀, 双压阀 (AND功能), 单向可调流量控制阀和快速排气阀

This part of ISO 19973 provides test procedures for assessing the reliability of the following types of pneumatic valves: — non-return (check) valves; — pilot-operated non-return valves; — shuttle valves; — dual pressure valves (AND function); — one-way adjustable flow control valves; — quick-exhaust valves by testing and the methods of reporting the results of testing. General test conditions and the calculation method are provided in ISO 19973-1. The methods specified in ISO 19973-1 apply to the first failure, as obtained with the three-points moving average (3PMA) method, without repairs, but excluding outliers. The lifetime of these pneumatic valves is usually given as a number of cycles. Therefore, whenever the term “time” is used in this part of ISO 19973, this variable is understood as a number of cycles. This part of ISO 19973 also specifies test equipment and threshold levels for tests to assess the reliability of these pneumatic valves.

Pneumatic fluid power - Assessment of component reliability by testing - Part 5: Non-return valves, shuttle valves, dual pressure valves (AND function), one-way adjustable flow control valves, quick-exhaust valves

BS ISO 19973-1:2015 气压传动.通过测试评定元件的可靠度.一般程序

Pneumatic fluid power. Assessment of component reliability by testing. General procedures

ISO 19973-1:2015 气压传动.通过测试评定元件的可靠度.第1部分:通用规程

This part of ISO 19973 provides general procedures, the calculation method for assessing the reliability of pneumatic fluid power components and the methods of reporting. These procedures are independent of the kinds of components and of their design. This part of ISO 19973 also provides general test conditions and a method for data evaluation. NOTE Because the service life of any component is subject to variations, a statistical evaluation assists the interpretation of the test results. The methods specified in this part of ISO 19973 apply to the first failure without repairs (see IEC 603003-5), but exclude outliers; however, because outliers can be highly significant, information about how to deal with them is given in Annex F.

Pneumatic fluid power - Assessment of component reliability by testing - Part 1: General procedures

DB13/T 2166-2014 汽车用液化天然气（LNG）加气机

Liquefied natural gas (LNG) dispenser for automobiles

KS I ISO TR 10686:2014 液压流体动力 将液压系统的清洁度与构成系统的部件和液压流体的清洁度联系起来的方法

Hydraulic fluid power — Method to relate the cleanliness of a hydraulic system to the cleanliness of the components and hydraulic fluid that make up the system

KS I ISO TR 10686-2014(2019) 液压流体动力 - 将液压系统的清洁度与构成系统的部件和液压油的清洁度相关联的方法

Hydraulic fluid power — Method to relate the cleanliness of a hydraulic system to the cleanliness of the components and hydraulic fluid that make up the system

BS ISO 6358-3:2014 气压流体动力. 使用可压缩流体组件的流速特性测定. 系统稳态流量特性的计算方法

Pneumatic fluid power. Determination of flow-rate characteristics of components using compressible fluids. Method for calculating steady-state flow-rate characteristics of systems

ISO 6358-3:2014 气压流体动力. 使用可压缩流体组件的流速特性测定. 第3部分: 系统稳态流量特性的计算方法

Pneumatic fluid power - Determination of flow-rate characteristics of components using compressible fluids - Part 3: Method for calculating steady-state flow-rate characteristics of systems

SAE J1927-2014 液压软管组件用累积损坏分析

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fati

Cumulative Damage Analysis for Hydraulic Hose Assemblies

BS ISO 19973-4:2014 气压液动. 通过试验评估部件的可靠性. 压力调节器

Pneumatic fluid power. Assessment of component reliability by testing. Pressure regulators

ISO 19973-4:2014 气压液动. 通过试验评估部件的可靠性. 第4部分: 压力调节器

This part of ISO 19973 provides test procedures for assessing the reliability of pneumatic pressure regulators by testing and the methods of reporting the results of testing. General test conditions and the calculation method are provided in ISO 19973-1. The methods specified in ISO 19973-1 apply to the first failure, as obtained with the three-points moving average (3PMA) method, without repairs, but excluding outliers. The lifetime of pneumatic pressure regulators is usually given as a number of cycles. Therefore, whenever the term “time” is used in this part of ISO 19973, this variable shall be understood as either cycles or time. This part of ISO 19973 applies to manually adjustable and remote-piloted pressure regulators, both relieving and non-relieving. This part of ISO 19973 does not apply to pressure regulators that have a permanent bleed. This part of ISO 19973 also specifies test equipment and failure criteria (threshold levels) for tests to assess the reliability of pneumatic pressure regulators. The life determined by the method in this part of ISO 19973 and in ISO 19973-1 will be more closely related to applications that have a large variation in flow rate. NOTE See Annex A for a flow chart illustrating the test procedure specified in this part of ISO 19973.

Pneumatic fluid power - Assessment of component reliability by testing - Part 4: Pressure regulators

JB/T 8884-2013 气动元件产品型号编制方法

本标准规定了气动元件和气动辅件型号的编制方法。本标准适用于以压缩空气或性能相当的其他工作介质的一般用途的气动元件和气动辅件。

Method for coding the type of pneumatic components

KS B 6277-2013 液压系统的一般规则

General Rules for Hydraulic Systems

KS B ISO 4414-2013 气动流体动力 有关系统的一般规则

Pneumatic fluid power－General rules relating to systems

KS B ISO 9110-1-2013 液压流体动力 测量技术 第1部分：一般测量原理

Hydraulic fluid power－Measurement techniques－Part 1：General measurement principles

KS B ISO 4413-2013 液压流体动力 有关系统的一般规则

Hydraulic fluid power－General rules relating to systems

KS B ISO 2944-2013 流体动力系统和部件 公称压力

Fluid power systems and components－Nominal pressures

KS B ISO 4414:2013 气流动力 系统与其组件总则与安全要求

Pneumatic fluid power－General rules relating to systems