23.100.99 其他流体动力系统部件 标准查询与下载

JB/T 4234-2013 普通型、限矩型液力偶合器 铸造叶轮技术条件

本标准规定了普通型、限矩型液力偶合器铸造叶轮的技术要求、试验方法、运输和贮存。本标准适用于普通型、限矩型液力偶合器的铸造叶轮(以下简称叶轮)。

General type and load limiting type of constant filling fluid couplings.Specification for casting impeller

JB/T 9001-2013 调速型液力偶合器 叶轮 技术条件

本标准规定了调速型液力偶合器、液力偶合器传动装置叶轮的技术要求。本标准适用于调速型液力偶合器、液力偶合器传动装置的叶轮。

Variable speed fluid couplings.Specification for impeller

KS B ISO 10945-2013 液压流体动力 气体蓄能器 气口尺寸

Hydraulic fluid power－Gas-loaded accumulators－ Dimensions of gas ports

KS B ISO 15217-2013 流体动力系统和元件 16毫米方形接地电连接器 特性和要求

Fluid power systems and components－16 mm square electrical connector with earth contact－Characteristics and requirements

KS B ISO 10771-1:2013 液压传动 金属压力容器外层的压力疲劳试验 第1部分：试验方法

Hydraulic fluid power－Fatigue pressure testing of metal pressure-containing envelopes－Part 1：Test method

KS B ISO 10945:2013 液压传动 充气蓄能器 气口尺寸

Hydraulic fluid power－Gas-loaded accumulators－ Dimensions of gas ports

KS B ISO 10946:2013 液压传动 隔离式充气蓄能器 优先选择的液压油口

Hydraulic fluid power－Gas-loaded accumulators with separator－Selection of preferred hydraulic ports

KS B ISO 15217:2013 流体传动系统和元件 带接地点的16mm方形电插头 特性和要求

Fluid power systems and components-16 mm square electrical connector with earth contact-Characteristics and requirements

JIS B 8358:2013 液压传动.气囊式蓄能器

Hydraulic fluid power.Bladder type accumulators

JB/T 11437-2013 空气压缩机压力控制器

本标准规定了空气压缩机压力控制器的型式、型号与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于一般环境条件下使用的直接或间接用于额定电压不超过交流660 V或直流1 000 V,额定功率不大于15 kW,额定压力不大于1.5 MPa的空气压缩机的通、断控制的压力控制器(以下简称控制器)。

Pressure control for air compressor

JB/T 6683-2011 全液压转向器配套阀.组合阀块

本标准规定了与摆线转阀式全液压转向器配套的组合阀块（以下简称组合阀块）的术语和定义、参量与符号、型式、基本参数与连接尺寸、技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于以液压油或性能相当的其他矿物油为工作介质的组合阀块。

Hydraulic steering unit counterpart valve.Combinatory valve block

JIS B 8378-1:2011 气动液能.压缩空气润滑器.第1部分:加入供应商文献中的主要特点和产品标记要求

Pneumatic fluid power -- Compressed-air lubricators -- Part 1: Main characteristics to be included in supplier's literature and product-marking requirements

DS/EN 14359+A1:2011 用于流体动力应用的充气蓄能器

1.1 This European Standard specifies the requirements for materials, design, manufacture, testing inspection, safety systems and documentation (including instructions for first operation), for commonly-used types of gas-loaded accumulators and gas bottles for fluid power applications (see 1.2).1.2 This European Standard applies to the following types of components, defined as the pressure-containing envelope of gas-loaded accumulators:- bladder type;- diaphragm type;- piston type;- transfer type;- gas bottles used to provide additional gas capacity.They consist of one or several parts joined together by a variety of mechanical means and by welding.1.3 This

Gas-loaded accumulators for fluid power applications

DIN EN 14359:2011 液压设备用充气式蓄能器;德文版本EN 14359-2006+A1-2010

Gas-loaded accumulators for fluid power applications; German version EN 14359:2006+A1:2010

LST EN 14359-2006+A1-2011 用于流体动力应用的充气蓄能器

Gas-loaded accumulators for fluid power applications

NF E48-150:2011 液压动力设备的气压蓄能器.

Gas-loaded accumulators for fluid power applications.

NF E48-150/IN1:2011 液压动力设备的气压蓄能器.

Gas-loaded accumulators for fluid power applications.

ANSI/IAPMO Z600-2011 带超额流量停止装置的柔性水连接器

The scope of this standard is to establish a generally acceptable standard for flexible water connectors that incorporate an excess flow shut-off mechanism used in water systems under continuous pressure and in accessible locations only. The intent of such devices is to protect personal property and building structures against water damage caused by accidental breakage, rupture.

Flexible Water Connector with Excess Flow Shutoff Device

JB/T 7938-2010 液压泵站.油箱.公称容积系列

本标准规定了液压泵站油箱公称容积系列。 本标准适用于以液压油或性能相当的其他液体为工作介质的液压泵站油箱。

Hydraulic fluid power.Power units.Nominal capacities of reservoir

GOST R 54012-2010 液压液力.液体自动颗粒计算器的校准.标准参考物质SRM 2806认证程序

Hydraulic fluid power. Calibration of liquid automatic particle counters. Procedures used to certify the standard reference material SRM 2806