25.100.10 车刀 标准查询与下载
共找到 219 条与 车刀 相关的标准，共 15 页
Настоящий стандарт распространяется на токарные проходные, подрезные резцы по ГОСТ 28980 и расточные резцы по ГОСТ 28981 с механическим крепле
Turning tools with indexable inserts of superhard materials. Specifications
- ICS
- 25.100.10
- CCS
- 发布
- 1992
- 实施
- 1994-01-01
Настоящий стандарт распространяется на вставки перетачиваемые, оснащенные режущим элементом из сверхтвердых материалов на основе нитри
Regrindale superhard material (composite) tipped cartridges for toolholders. Specifications
- ICS
- 25.100.10
- CCS
- 发布
- 1992
- 实施
- 1994-01-01
Cutters for internal turning with super hand materials inserts. Types and basic dimensions
- ICS
- 25.100.10
- CCS
- 发布
- 1991
- 实施
- 1992-01-01
Lathe assmbly parting and grooving blades. Types and basic dimensions
- ICS
- 25.100.10
- CCS
- 发布
- 1991
- 实施
- 1992-01-01
Cutters for external turning with super hand materials inserts. Types and basic dimensions
- ICS
- 25.100.10
- CCS
- 发布
- 1991
- 实施
- 1992-01-01
Square portion of shanks for small tools
- ICS
- 25.100.10
- CCS
- J52
- 发布
- 1990-06-01
- 实施
- 1990-06-01
Hydraulic fluid power. Determination of characteristics of motors. Part 1 : at constant pressure and at constant low speed.
- ICS
- 25.100.10
- CCS
- J20
- 发布
- 1990-05-01
- 实施
- 1990-05-20
Hydraulic fluid power; determination of characteristics of motors; part 1: at constant low speed and at constant pressure
- ICS
- 25.100.10
- CCS
- J20
- 发布
- 1989-08
- 实施
- 1989-08-15
Boring tools with changeable indexable inserts. Types and basic dimensions
- ICS
- 25.100.10
- CCS
- 发布
- 1989
- 实施
- 1990-01-01
この規格は，主として金属の切削加工に用いる高速度鋼付刃バイト(以下，ぐイトという。)について規定する。
High speed steel tipped tools
- ICS
- 25.100.10
- CCS
- J41
- 发布
- 1988-03-01
- 实施
Ground high speed steel tool bits
- ICS
- 25.100.10
- CCS
- J41
- 发布
- 1987-02-01
- 实施
- 1987-02-01
Turning tools. Cutting-off tool holders. Designation. Code of symbolization.
- ICS
- 25.100.10
- CCS
- J41
- 发布
- 1986-06-01
- 实施
- 1986-06-20
Turning tools. Cutting off tool holders. Form and dimensions.
- ICS
- 25.100.10
- CCS
- J41
- 发布
- 1986-06-01
- 实施
- 1986-06-20
Schválenie ST SEV 4599-84 doporu?ilo Federálne ministerstvo v?e obecného strojárstva. Spracovatel a odborové normaliza?ně st?edisko: Továrně stroja? skej techniky, koncernov? V?skumn? ústav náradia VUNAR, Nové Zám ky — Ing. Eudovít Mészáros Pracovník ??adu p?e normalizáciu a meranie: Ing. Krista Komrsková
Turning and copying tools with replaceable cutting tips. Marking
- ICS
- 25.100.10
- CCS
- 发布
- 1985-11-16
- 实施
Single point tool holders for turning and copying, for indexable inserts — Dimensions
- ICS
- 25.100.10
- CCS
- 发布
- 1985-09-05
- 实施
Ground high speed steel tool bits. Dimensions.
- ICS
- 25.100.10
- CCS
- J41
- 发布
- 1985-07-01
- 实施
- 1985-07-05
This Standard establishes specifications for the following factors of tool life testing with single-point turning tools: workpiece, tool, cutting fluid, cutting conditions, tool wear and tool life, equipment, test procedures, recording and reporting and presentation of results. Further general information is given in Appendix A.
Tool Life Testing with Single-Point Turning Tools Revision of ANSI B94.34-1946 and B94.36-1956
- ICS
- 25.100.10
- CCS
- J41
- 发布
- 1985-01-01
- 实施
Настоящий стандарт распространяется на токарные расточные резцы с механическим креплением сменных многогранных пластин, изготовляемые
Boring tools with clamped shangeable inserts pressed from the top. Design and dimensions
- ICS
- 25.100.10
- CCS
- 发布
- 1985
- 实施
- 1986-07-01
Establishes specifications for the following factors of tool life testing with single - point turning tools: workpiece, tool, cutting fluid, cutting conditions, tool wear and tool life, equipment, test procedures, recording and reporting and presentation of results.
Tool Life Testing with Single-Point Turning Tools
- ICS
- 25.100.10
- CCS
- J41
- 发布
- 1985
- 实施
Настоящий стандарт распространяется на токарные проходные, подрезные, копировальные и расточные резцы с механическим креплением сменных
Lathe tools with mechanically clamped indexable inserts. Specifications
- ICS
- 25.100.10
- CCS
- 发布
- 1985
- 实施
- 1986-07-01
