25.160.40 焊接接头 标准查询与下载

ISO 5173:2023 金属材料焊缝的有损检验.弯曲测试

This document specifies a method for making transverse root, face and side bend tests on test specimens taken from butt welds, butt welds with cladding (subdivided into welds in clad plates and clad welds) and cladding without butt welds, in order to reveal imperfections on or near the surface of the test specimen which is under tension during bend testing and/or assess ductility. It also gives the dimensions of the test specimen. In addition, this document specifies methods to be used instead of transverse bend tests with a former for welded joints when base materials, heat affected zones and/or weld metal have a significant difference in their physical and mechanical properties in relation to bending. This document applies to metallic materials in all forms of product with welded joints made by any welding process.

Destructive tests on welds in metallic materials — Bend tests

EN ISO 4761:2022 焊缝的无损检测.薄壁钢构件的相控阵超声波检测（UT-PA）.验收水平

This document specifies acceptance levels for the phased array ultrasonic testing technique (UT-PA) of full-penetration welds in low-alloy and/or fine-grained steels in the wall thickness range from 3,2 mm to 8 mm which correspond to the quality levels of ISO 5817. These acceptance levels are applicable to indications detected according to ISO 20601.

Non-destructive testing of welds - Phased array ultrasonic testing (UT-PA) for thin-walled steel components - Acceptance levels (ISO 4761:2022)

KS B ISO 5178:2022 金属材料焊缝的破坏性试验.熔焊接头焊缝金属的纵向拉伸试验

Destructive tests on welds in metallic materials — Longitudinal tensile test on weld metal in fusion welded joints

KS B ISO 9015-2-2022 金属材料焊缝的破坏性试验.硬度试验.第2部分:焊接接头的显微硬度试验

Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness testing of welded joints

KS B ISO 9017:2022 金属材料焊缝的破坏性试验.断裂试验

Destructive tests on welds in metallic materials — Fracture test

KS B ISO 9017-2022 金属材料焊缝的破坏性试验.断裂试验

Destructive tests on welds in metallic materials — Fracture test

KS B ISO 10042-2022 铝及其可焊接合金的电弧焊接接头.缺陷质量等级指南

Arc-welded joints in aluminium and its weldable alloys — Guidance on quality levels for imperfections

KS B ISO 9015-2:2022 金属材料焊缝的破坏性试验.硬度试验.第2部分:焊接接头的显微硬度试验

Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness testing of welded joints

KS B ISO 10042:2022 铝及其可焊接合金的电弧焊接接头.缺陷质量等级指南

Arc-welded joints in aluminium and its weldable alloys — Guidance on quality levels for imperfections

KS B ISO 5178-2022 金属材料焊缝的破坏性试验.熔焊接头焊缝金属的纵向拉伸试验

Destructive tests on welds in metallic materials — Longitudinal tensile test on weld metal in fusion welded joints

EN ISO 10447:2022 电阻焊接.点焊,凸焊和有缝焊的剥离和凿剥离试验

This document specifies the procedures and recommended tooling to be used for peel and chisel testing of resistance spot and embossed projection welds. This document applies to welds made in two or more sheets in the thickness range of 0,5 mm to 3,0 mm. The aim of these tests is to determine: — weld size and failure mode when welds are destructively tested; — verification of welds by non-destructive chisel tests. NOTE The preferred method of peel testing seam welds (mechanized peel testing) is covered in ISO 14270.

Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2022)

KS B 0953-2022 对接压力焊接接头的试验方法

Method of test for butt pressure welded joints

KS B 0524-2022 焊接.奥氏体和双铁素体奥氏体Cr-Ni不锈钢焊接金属中铁素体数（FN）的测定

Welding — Determination of Ferrite Number(FN) in austenitic and duplex ferritic-austenitic Cr-Ni stainless steel weld metals

BS EN ISO 7963:2022 非破坏性测试 超声波检测 2 号校准块规格

1   Scope This document specifies the requirements for the dimensions, material, manufacture and methods of use for calibration block No. 2 for setting and checking ultrasonic test equipment.

Non-destructive testing. Ultrasonic testing. Specification for calibration block No. 2

ISO 10447:2022 电阻焊.焊缝试验.电阻点焊和凸焊的剥离和凿削试验

Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds

EN ISO 7963:2022 无损检测.超声波检验.2号基准块规范

This document specifies the requirements for the dimensions, material, manufacture and methods of use for calibration block No. 2 for setting and checking ultrasonic test equipment.

Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2022)

BS EN ISO 10675-2:2021 焊缝的无损检测 射线照相测试的可接受水平 铝及其合金

Non-destructive testing of welds. Acceptance levels for radiographic testing - Aluminium and its alloys

T/ZAMEE 10-2022 城镇燃气聚乙烯(PE)管道热熔接头X射线检测方法

本文件规定了城镇燃气聚乙烯(PE)管道热熔接头X射线检测的有关控制因素，包括检测人员、检测设备和器材、检测工艺及其选择、检测结果评定和质量分级、检测记录和报告。本文件主要适用于城镇燃气聚乙烯(PE)管道热熔接头X射线检测，城镇燃气聚乙烯(PE)管道电熔接头X射线检测可参考使用。

X-radiographic testing method for fusion-butt joints of town gas polyethylene (PE) pipes

22/30457015 DC BS EN 12814-7 热塑性塑料半成品焊接接头试验第7部分：腰部试样拉伸试验

BS EN 12814-7. Testing of welded joints of thermoplastics semi-finished products - Part 7. Tensile test with waisted test specimens

EN ISO 17636-2:2022 无损检测的焊缝射线检测-第2部分:X -和γ射线技术与数字探测器

This document specifies techniques of digital radiography with the object of enabling satisfactory and repeatable results. The techniques are based on generally recognized practice and fundamental theory of the subject. This document applies to the digital radiographic testing of fusion welded joints in metallic materials. It applies to the joints of plates and pipes. Besides its conventional meaning, “pipe”, as used in this document, covers other cylindrical bodies such as tubes, penstocks, boiler drums and pressure vessels. This document specifies the requirements for digital radiographic X- and gamma-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDAs) of the welded joints of metallic plates and tubes for the detection of imperfections. It includes manual and automated inspection with DDAs. Digital detectors provide a digital grey value image which can be viewed and evaluated using a computer (Annex E). This document specifies the recommended procedure for detector selection and radiographic practice. Selection of computer, software, monitor, printer and viewing conditions are important, but are not the main focus of this document. The procedure specified in this document provides the minimum requirements for radiographic practice which permits exposure and acquisition of digital radiographs with equivalent sensitivity for the detection of imperfections as film radiography (specified in ISO 17636-1). This document does not specify acceptance levels for any of the indications found on the digital radiographs. ISO 10675 provides information on acceptance levels for weld inspection. If contracting parties apply lower test criteria, it is possible that the quality achieved will be significantly lower than when this document is strictly applied.

Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2022, Corrected version 2023-02)