25.160.50 钎焊和低温焊 标准查询与下载

T/CASME 1413-2024 钎焊用药芯类焊丝制造工艺规范

本文件规定了钎焊用药芯类焊丝的制造工艺要求、技术要求、试验方法、检验及判定规则、标志和包装等内容。

Manufacturing process specification for brazing flux cored welding wire

BS EN ISO 9455-17:2024 软焊剂 测试方法表面绝缘电阻梳状测试和助焊剂残留物电化学迁移测试

Soft soldering fluxes. Test methods - Surface insulation resistance comb test and electrochemical migration test of flux residues

ASTM B678-23 金属涂层产品可焊性的标准测试方法

1.1  This test method provides a procedure for evaluating the solderability of metallic-coated products and test specimens to assure satisfactory performance in manufacturing processes requiring soldering with soft (tin-lead) solder and rosin flux. This test method is applicable only for testing coatings that are normally readily solderable such as: tin, tin-lead alloy, silver, and gold. 1.2  This test method is qualitative and broadly applicable. It is easy to perform and requires only simple equipment. There are other solderability tests not covered by this test method that are more applicable to specific situations, yield quantitative results, or both. Several are described in the literature.2 This is a “go-no-go” test and does not grade solderability as excellent, good, fair, and so forth. 1.3  This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Solderability of Metallic-Coated Products

BS EN ISO 18279:2023 钎焊 钎焊接头的缺陷

Brazing. Imperfections in brazed joints

ISO 18279:2023 钎焊——钎焊接头的缺陷

Brazing — Imperfections in brazed joints

23/30444564 DC BS ISO 9455-18 软焊剂 测试方法 第18部分：清洁之前和/或之后焊接印刷电路组件清洁度的测试方法

BS ISO 9455-18. Soft soldering fluxes.Test methods - Part 18. Test methods of cleanliness of the soldered printed circuit assemblies before and/or after cleaning

23/30475728 DC BS EN ISO 3677 钎焊填充金属 指定

BS EN ISO 3677. Filler metal for brazing. Designation

ISO/DIS 9455-18:2023 软焊剂 试验方法 第18部分：清洁前和/或后焊接印刷电路组件清洁度的试验方法

Soft soldering fluxes — Test methods — Part 18: Test methods of cleanliness of the soldered printed circuit assemblies before and/or after cleaning

EN ISO 5179:2023 使用不同间距试件的可钎焊性研究

This document specifies three test methods for investigating brazeability. A spreading test shows testing method with measurement of the spread area of the filler metals. A T-joint test describes a scheme to construct a T-shape design by the test pieces and a testing method. A varying gap test describes a test piece and a testing method for assessing the influence of the various parameters which can influence brazing during manufacture as a function of clearances.

Investigation of brazeability with spreading and gap-filling test (ISO 5179:2021)

ISO/CD 3677:2023 钎焊和钎焊用填充金属 名称

Filler metal for soldering and brazing — Designation

ISO/CD 9455-18:2023 软焊剂 测试方法 第 18 部分：第 18 部分：清洁之前和/或之后焊接印刷电路组件清洁度的测试方法

Soft soldering fluxes — Test methods — Part 18: Part 18: Test methods of cleanliness of the Soldered Printed Circuit Assemblies before and/or after cleaning

ISO/DIS 12224-2:2023 药芯焊丝 规格和试验方法 第2部分：焊剂含量的测定

Flux cored solder wire — Specification and test methods — Part 2: Determination of flux content

ISO/DIS 12224-1:2023 实心和药芯焊丝 规范和测试方法 第 1 部分：分类和性能要求

Solder wire, solid and flux cored — Specification and test methods — Part 1: Classification and performance requirements

23/30459394 DC BS EN ISO 17672 钎焊 填充金属

BS EN ISO 17672. Brazing. Filler metal

T/CSTM 00921-2023 微波组件用焊锡膏性能测试及应用

本文件规定了微波组件用焊锡膏基本理化性能、腐蚀性能、电气绝缘性能、印刷性能、焊接性能、机械互连特性、对信号传输损耗的影响及焊点可靠性的测试方法。 本文件适用于印刷焊锡膏，喷印焊锡膏和点涂焊锡膏可参考本文件执行。

Performance test and application verification method of solder paste for microwave assembly

BS EN ISO 9455-6:2022 软焊剂 测试方法 卤化物（不含氟化物）含量的测定与检测

1   Scope This document specifies three quantitative methods for the determination of the ionic halide (excluding fluoride) content of soldering fluxes. Halides are calculated as chlorides. A useful qualitative test method for the detection of ionic halides is also described. Method A is a potentiometric titration method for the determination of halide (excluding fluoride) content and is applicable to flux classes 1 and 2, defined in ISO 9454‑1. This method, which is considered the reference method for these fluxes, is suitable for halide contents generally within the range of 0,05 % mass fraction to 2 % mass fraction in the non-volatile matter of the flux. Method B is a titration method for the determination of the total halide (excluding fluoride) content of water-soluble fluxes. It is applicable to flux classes 2122 to 2124, 3112 to 3114 and 3212 to 3214, as defined in ISO 9454‑1. Method C is a titration method for the determination of the halide (excluding fluoride) content of water-soluble fluxes containing phosphates and is applicable to flux class 331, as defined in ISO 9454‑1. Method D is a qualitative test, using silver chromate test paper, for the presence of ionic halides. The technique can be used for all classes of flux.

Soft soldering fluxes. Test methods. Determination and detection of halide (excluding fluoride) content

BS EN ISO 9455-1:2022 软焊剂 测试方法-不挥发物的测定 重量法

1   Scope This document specifies a gravimetric method for the determination of the content of non-volatile matter in soft soldering fluxes. It is applicable to liquid and paste fluxes of type 1, as defined in ISO 9454‑1.

Soft soldering fluxes. Test methods - Determination of non-volatile matter, gravimetric method

EN ISO 9455-6:2022 软钎焊剂.试验方法.第6部分:卤化物(不包括氟化物)含量的检测和测定

This document specifies three quantitative methods for the determination of the ionic halide (excluding fluoride) content of soldering fluxes. Halides are calculated as chlorides. A useful qualitative test method for the detection of ionic halides is also described. Method A is a potentiometric titration method for the determination of halide (excluding fluoride) content and is applicable to flux classes 1 and 2, defined in ISO 9454-1. This method, which is considered the reference method for these fluxes, is suitable for halide contents generally within the range of 0,05 % mass fraction to 2 % mass fraction in the non-volatile matter of the flux. Method B is a titration method for the determination of the total halide (excluding fluoride) content of water-soluble fluxes. It is applicable to flux classes 2122 to 2124, 3112 to 3114 and 3212 to 3214, as defined in ISO 9454-1. Method C is a titration method for the determination of the halide (excluding fluoride) content of water-soluble fluxes containing phosphates and is applicable to flux class 331, as defined in ISO 9454-1. Method D is a qualitative test, using silver chromate test paper, for the presence of ionic halides. The technique can be used for all classes of flux.

Soft soldering fluxes - Test methods - Part 6: Determination and detection of halide (excluding fluoride) content (ISO 9455-6:2022)

T/ZZB 3025-2022 硼酸三甲酯助焊剂

本文件规定了硼酸三甲酯助焊剂（以下简称“助焊剂” ）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、安全技术说明书、包装、运输、贮存和质量承诺。 本文件适用于各种硬钎焊用的硼酸三甲酯助焊剂。

Trimethyl borate flux for brazing

ISO 9455-6:2022 软钎焊剂.试验方法.第6部分:卤化物（不含氟化物）含量的测定和检测

Soft soldering fluxes — Test methods — Part 6: Determination and detection of halide (excluding fluoride) content