29.035.99 其他绝缘材料 标准查询与下载

GOST 4248-2018 电工用的耐电弧的石棉水泥板 技术条件

Chrysotile cement non-arcing boards for electrical purposes (ACEID). Specifications

ASTM D2967-07(2017) 粉末涂料角覆盖的标准试验方法

1.1 This test method covers the determination of the ratio of corner thickness (see 3.1.3) to face thickness (see 3.1.4) of powder coatings applied to a specific face thickness by dipping preheated square bars into aerated powder and curing the coating using predetermined conditions. NOTE 1—The property of corner coverage has also been referred to as “edge coverage,” though the latter is not recommended. There are widespread misunderstandings and expectations relative to the term “edge coverage.” This test is performed on a steel bar having square corners and the results do not necessarily relate to edges that are sharper, that is, burrs. A coating that has measurable corner coverage may still not protect sharper edges from corrosion or provide the electrical insulation needed in some applications. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Corner Coverage of Powder Coatings

JB/T 13144-2017 电工用聚对苯二甲酸乙二酯（PET）热收缩管

Polyethylene terephthalate (PET) heat shrink tubing for electricians

JB/T 10443.1-2017 电气用层压纸板 第1部分：定义、分类和一般要求

Laminated paperboard for electrical applications Part 1: Definitions, classification and general requirements

JB/T 10443.2-2017 电气用层压纸板 第2部分：试验方法

Laminated cardboard for electrical applications Part 2: Test methods

JB/T 10442.1-2017 电气用菱格涂胶绝缘纸 第1部分：定义和一般要求

Diamond-coated insulating paper for electrical applications Part 1: Definitions and general requirements

JB/T 13145-2017 电气绝缘用水溶性半无机硅钢片漆

Electrical insulation water-soluble semi-inorganic silicon steel sheet paint

JB/T 10443.3-2017 电气用层压纸板 第3部分：LB3.1A.1和LB3.1A.2型预压纸板

Laminated cardboard for electrical purposes Part 3: Pre-pressed cardboard types LB3.1A.1 and LB3.1A.2

JB/T 12878-2016 母线绝缘用聚烯烃热收缩管

Polyolefin heat shrinkable tube for busbar insulation

JB/T 12876-2016 半硬质聚烯烃热收缩管

Semi-rigid polyolefin heat shrink tubing

JB/T 12879-2016 中厚壁聚烯烃热收缩管

Medium thick wall polyolefin heat shrink tubing

JB/T 12874-2016 阻燃双壁聚烯烃热收缩管

Flame retardant double wall polyolefin heat shrink tubing

JB/T 12873-2016 非阻燃双壁聚烯烃热收缩管

Non-flame retardant double wall polyolefin heat shrink tubing

JB/T 12877-2016 柔软型聚烯烃热收缩管

Flexible polyolefin heat shrinkable tube

JB/T 12875-2016 阻燃聚烯烃热收缩管

Flame retardant polyolefin heat shrink tubing

JB/T 12426-2015 电气用热收缩聚四氟乙烯软管

本标准规定了电气用热收缩聚四氟乙烯软管的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于低收缩比和高收缩比的电气用热收缩聚四氟乙烯软管。

Heat-shrinkable PTFE sleeving for electrical purposes

JB/T 12423-2015 电气用聚碳酸酯薄膜

本标准规定了电气用聚碳酸酯薄膜的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于电气用聚碳酸酯薄膜。

Polycarbonate (PC) films used for electrical insulation

JB/T 12422-2015 电气绝缘材料和绝缘制件局部放电试验方法

本标准规定了电气绝缘材料和绝缘制件局部放电试验的术语和定义、试验回路、测量仪器、测量不确定度及灵敏度、试样和电极、试验电压要求、试验程序、试验报告。 本标准适用于固体绝缘材料、绝缘制件在50 Hz交流电压下的局部放电测量。

Test method for partial discharge of electrical insulating materials and insulating parts

JB/T 12421-2015 变频电机用绝缘材料耐重复脉冲电应力试验方法

本标准规定了变频电机用绝缘材料耐重复脉冲电应力试验的预处理条件、仪器、试样、试验条件、试验规程、试验数量及结果、应考虑的因子、报告。 本标准适用于评定变频电机用绝缘材料耐重复脉冲电应力的能力。

Test method for electrical stress endurance under repetitive impulse of insulation materials for frequency conversion motor

JB/T 12429-2015 核电站1E级热缩电力电缆连接件

本标准规定了核电站1E级热缩电力电缆连接件的术语和定义、分类、技术要求、试验方法、标志、包装、运输和贮存。 本标准适用于核电站1E级热缩电力电缆连接件。

Class 1E heat-shrinkable power cable splices in nuclear power generating stations