共找到 885 条与 磁性元件 相关的标准,共 59 页
Fixed inductors for electromagnetic interference suppression - Part 1: Generic specification (IEC 60938-1:2021)
Transformers and inductors for use in electronic and telecommunication equipment - Measuring methods and test procedures (german version)
This part of IEC 62024 specifies the measuring methods of the rated direct current limits for small inductors. Standardized measuring methods for the determination of ratings enable users to accurately compare the current ratings given in various manufacturers´ data books.
High frequency inductive components - Electrical characteristics and measuring methods - Part 2: Rated current of inductors for DC-to-DC converters (IEC 62024-2:2020); German version EN IEC 62024-2:2020
Fixed inductors for electromagnetic interference suppression. Sectional specification on power line chokes
Test method for the mechanical strength of cores made of magnetic oxides
Ferrite cores ― Dimensions ― Part 8: E-cores
Terms and nomenclature for cores made of magnetically soft ferrites-Part 1:Terms used for physical irregularities
Fixed inductors for electromagnetic interference suppression – Part 2: Sectional specification on power line chokes
Terms and nomenclature for cores made of magnetically soft ferrites - Part 1: Terms used for physical irregularities and reference of dimensions (german version)
This corrigendum 1 corrects the formula (2), (3) ande (4) in the clause 3 \
Cores made of soft magnetic materials - Measuring methods - Part 2: Magnetic properties at low excitation level (IEC 62044-2:2005/COR1:2021); German version EN 62044-2:2005/AC:2021-06
Cores made of soft magnetic materials - Measuring methods - Part 2: Magnetic properties at low excitation level (IEC 62044-2:2005/COR1:2021)
Fixed inductors for electromagnetic interference suppression. Generic specification
Fixed inductors for electromagnetic interference suppression – Part 1: Generic specification
Cores made of soft magnetic materials - Measuring methods - Part 2: Magnetic properties at low excitation level
Dimensional tolerances of ferrite cores
Dimensional tolerances of ferrite cores
Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities - Part 1: General specification (german version)
This part of IEC 60938 applies to fixed inductors designed for electromagnetic interference suppression, which will be connected to an AC mains or other supply with a nominal voltage not exceeding 1000 V AC RMS or 1500 V DC with a nominal frequency not exceeding 400 Hz. This sect
Fixed inductors for electromagnetic interference suppression - Part 2: Sectional specification on power line chokes
IEC 62317-2:2010 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of pot-cores made of ferrite, and the dimensional limits for coil formers to be used with them. The selection of core sizes for this standard is based on the philosophy of including those sizes which are industrial standards, either by inclusion in a national standard, or by broad-based use in industry. See IEC 62317-1 for more detail concerning the philosophy of selecting core sizes to be included. This first edition cancels and replaces the fourth edition of IEC 60133 published in 2000. The main changes with respect to the previous edition of IEC 60133 are listed below: - changed "e dimension" of P4,6/3,1 in Table 6 from 3,20 Max. to 3,40 Max.; - removed "derived standards" from Annex B (informative) in the fourth edition of IEC 60133; - changed the name of core parts in Subclause 3.1.2 from "Grooves" to "Wire-ways" in accordance with IEC 62317-1 Subclause 5.6.
Ferrite cores - Dimensions - Part 2: Pot-cores for use in telecommunications, power supply, and filter applications
Transformers and inductors for use in electronic and telecommunication equipment – Measuring methods and test procedures
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号