29.130.20 低压开关装置和控制器 标准查询与下载

PN-EN IEC 60947-5-8-2021-08 E 低压开关设备和控制设备 第5-8部分：控制电路装置和开关元件 三位使能开关（IEC 60947-5-8:2020）

Low-voltage switchgear and controlgear--Part 5-8: Control circuit devices and switching elements--Three-position enabling switches (IEC 60947-5-8:2020)

DIN EN IEC 60947-5-8:2021 低压开关设备和控制设备 第 5-8 部分：控制电路设备和开关元件 三位置启用开关（IEC 60947-5-8:2020）；德文版 EN IEC 60947-5-8:2021

This part of IEC 60947 specifies requirements for three-position enabling switches. These switches are used as components of enabling devices described in 10.9 of IEC 60204-1 to provide signals that, when activated, allow machine operation to be initiated by a separate start cont

Low-voltage switchgear and controlgear - Part 5-8: Control circuit devices and switching elements - Three-position enabling switches (IEC 60947-5-8:2020); German version EN IEC 60947-5-8:2021

LST EN IEC 61439-1:2021 低压开关设备和控制设备组件 第1部分：一般规则（IEC 61439-1:2020）

Low-voltage switchgear and controlgear assemblies - Part 1: General rules (IEC 61439-1:2020)

LST EN IEC 61439-2:2021 低压开关设备和控制设备组件 第2部分：电力开关设备和控制设备组件（IEC 61439-2:2020）

Low-voltage switchgear and controlgear assemblies - Part 2: Power switchgear and controlgear assemblies (IEC 61439-2:2020)

T/ZZB 2166-2021 电感式接近开关

本文件规定了电感式接近开关的术语和定义、分类和、特性和正常使用条件、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和储存、质量承诺。 本文件适用于通过感应金属物体而动作的电感式圆柱螺纹型接近开关（以下简称接近开关）。该接近开关具有半导体开关元件，可用于连接额定电压交流不超过250 V（50 Hz或60 Hz），或直流不超过300 V的电路。

Inductive proximity switches

LST EN IEC 60947-4-1/AC:2021 低压开关设备和控制设备 第 4-1 部分：接触器和电机启动器 机电接触器和电机启动器（IEC 60947-4-1:2018/COR2:2021）

Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters (IEC 60947-4-1:2018/COR2:2021)

PN-EN IEC 60947-1-2021-07 E 低压开关设备和控制设备 第1部分：一般规则（IEC 60947-1:2020）

Low-voltage switchgear and controlgear -- Part 1: General rules (IEC 60947-1:2020)

IEC 60947-8:2021 低压开关设备和控制设备. 网路工业设备的设备外观. 第8部分: 转动发电机内置热防护装置(PTC)的控制器

This part of IEC 60947 series specifies requirements for control units, which control a switching device in response to the PTC thermistors incorporated in rotating electrical machines and the industrial application. It specifies requirements for that type of system comprising a

Low-voltage switchgear and controlgear - Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines

T/EQTA 003-2021 配电设备母线制作及安装工艺

为了使大连市高低压成套产品质量更加安全可靠，使各企业生产过程配电设备母线制作安装工艺更加规范化、标准化、正规化。大连市电气质量技术协会与大连新诚电控有限公司牵头，组织多家会员单位，研究制定了《配电设备母线制作及安装工艺》团体标准。 本标准的技术特点，是经过实践和较深入的研究后形成的：  （一） 标准范围  《配电设备母线制作及安装工艺》本标准规定了高低压成套设备母线制作及安装工艺的设备工具材料、工艺准备、母线选择、工艺过程、铜排制作工艺、母线压缩工艺、母线相序工艺要求、软母线（BVR）的制作工艺、母线安装工艺要求、检查、特殊要求内容。 本标准适用于大连市高低压成套设备生产行业的高低压成套设备制造的母线制作安装工艺。 （二）构成原则                              1.适用性：适用用于大连市高低压成套设备生产行业的高低压成套设备制造的母线制作安装工艺。。  2.前瞻性：跟踪社会发展、科技进步，适度前瞻；  3.相关性：本标准的编写参照GB/T 1.1-2009《标准化工作导则 第1部分：标准的结构和编写》的有关规定。本标准是大连市电气行业系列团体标准之一。本标准的结构、章条编号、编制原则、使用的定义和术语具有统一性； 4.开放性：标准体系是开放的，适应社会发展、科技进步；  5.普适性：标准体系具有一般意义的普遍适用规则。     本标准的制定符合企业生产需求，使生产和产品规范化、标准化、正规化，具有较强的可操作性。

Production and installation process of power distribution equipment busbar

GSO IEC 61439-7:2021 低压开关设备和控制设备组件 第7部分：用于特定应用的组件 例如码头、露营地、市场广场、电动汽车充电站

IEC 61439-7:2018 defines the specific requirements of assemblies as follows: - assemblies for which the rated voltage does not exceed 1 000 V in the case of AC or 1 500 V in the case of DC; – assemblies intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electric energy consuming equipment; – assemblies operated by ordinary persons (e.g. plug and unplug of electrical equipment); – assemblies intended to be installed and used in market squares, marinas, campsites and other similar outdoor public sites; – assemblies intended for charging stations for electric vehicles (AEVCS) for Mode 3 and Mode 4. They are designed to integrate the functionality and additional requirements for electric vehicle conductive charging systems according to IEC 61851-1:2017. This first edition cancels and replaces the relevant technical specification published in 2014. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous technical specification: a new classification of the stationary ASSEMBLIES in accordance with their mechanical resistance (5.702); a new Table 702 with the list of tests and relevant severities to which the ASSEMBLIES have to be subjected according to the classification mentioned at point a); a new Annex (CC) with a new endurance test for the individual switching devices intended to be used in AEVSC, if they have not already been tested against this requirement; a general editorial review and a technical revision. The contents of the corrigendum of August 2019 have been included in this copy.

Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations

GSO IEC TR 63054:2021 低压开关设备和控制设备 火灾风险分析和风险降低措施

IEC TR 63054:2017(E) applies to the fire risk analysis of low-voltage switchgear and controlgear (hereinafter referred to as "equipment") referring to the IEC 60947 relevant publications, where the following applies: - only the case where a fire originates (typically under fault or misuse conditions) within the equipment; - only equipment installed in normal environments. Hazardous environments, for example in presence of combustible materials, is not to be considered; - only the case of products selected, installed and used according to the manufacturer instructions and installation rules. In addition, the following cases are not considered: - faults addressed by IEC TR 61641; - risks due to smoke emissions; - double faults, i.e. multiple phenomenon, potentially combined.

Low-voltage switchgear and controlgear - Fire risk analysis and risk reduction measures

T/EQTA 002-2021 成套设备元器件安装及配线工艺

近年来，大连市低压成套设备产业发展很快，截至目前，低压成套制造企业有一百多家，为大连市经济发展注入强劲动力。由于低压成套设备制造采用了国际IEC标准等同采用的国家标准（GB7251系列标准），对产品质量要求较高，同时又是列入国家强制产品认证目录中的产品，对产品电气安全质量要求更高，因此对企业生产制造过程的质量控制尤为重要，尤其是成套设备元器件安装及配线工艺的技术要求很高，但是目前国家标准及行业标准、地方标准中并未对成套设备元器件安装及配线工艺提出具体要求和规定，各个企业都是自行制定一些企业内控技术文件加以规范，致使成套设备质量出现差异。 为了使大连市高低压成套设备产品质量更加安全可靠，使各企业生产过程更加规范化、标准化、正规化。大连市电气质量技术协会与大连新诚电控有限公司牵头，组织多家会员单位，研究制定了《成套设备元器件安装及配线工艺》团体标准。 本标准的技术特点，是经过实践和较深入的研究后形成的：  （一） 标准范围  本标准规定了高低压成套设备元器件安装及配线工艺的设备工具材料、工艺准备、工艺过程、工艺要求。 （二）构成原则                              1.适用性：本标准适用于大连市高低压成套设备生产行业的元器件安装及配线工艺  2.前瞻性：跟踪社会发展、科技进步，适度前瞻；  3.相关性：本标准的编写参照GB/T 1.1-2009《标准化工作导则 第1部分：标准的结构和编写》的有关规定。本标准是大连市电气行业系列团体标准之一。本标准的结构、章条编号、编制原则、使用的定义和术语具有统一性； 4.开放性：标准体系是开放的，适应社会发展、科技进步；  5.普适性：标准体系具有一般意义的普遍适用规则。     本标准的制定符合企业生产需求，使生产和产品规范化、标准化、正规化，具有较强的可操作性。

Complete set of equipment components installation and wiring process

GSO IEC 61439-4:2021 低压开关设备和控制设备组件 第4部分：建筑工地组件的特殊要求 (ACS)

IEC 61439-4:2012 defines the specific requirements of ACS as follows: - ASSEMBLIES for which the rated voltage does not exceed 1 000 V in case of a.c. or 1 500 V in case of d.c.; - ASSEMBLIES where the nominal primary voltage and the nominal secondary voltage of transformers incorporated in ACS are within the limits specified above; - ASSEMBLIES intended for use on construction sites, both indoors and outdoors, i.e. temporary places of work to which the public do not generally have access and where building construction, installation, repairs, alteration or demolition of property (buildings) or civil engineering (public works) or excavation or any other similar operations are carried out; - transportable (semi-fixed) or mobile ASSEMBLIES with enclosure. The manufacture and/or assembly may be carried out other than by the original manufacturer. This first edition of IEC 61439-4 cancels and replaces the second edition of IEC 60439-4 (2004), and constitutes a technical revision. This edition includes the following significant technical changes with respect to the last edition of IEC 60439-4: - modification of the title as "Part 4: Particular requirements for assemblies for construction sites (ACS)"; - alignment on IEC 61439-1 regarding the structure and technical content, as applicable; - to allow comparison with tested ACS. This publication is to be read in conjunction with IEC 61439-1:2011.

Low-voltage switchgear and controlgear assemblies - Part 4: Particular requirements for assemblies for construction sites (ACS)

GSO IEC 62683-1:2021 低压开关设备和控制设备 用于信息交换的产品数据和属性 第1部分：目录数据

IEC 62683-1:2017 establishes the reference dictionary of the general description of low-voltage switchgear and controlgear classes based on defined properties. This dictionary is used to facilitate the exchange in electronic format of data describing low-voltage switchgear and controlgear. This document provides clear and unambiguous definitions of a limited number of properties and classes which are mainly used for presentation, selection and identification of products particularly in electronic catalogues. Each property has an unambiguously defined meaning and naming, and, where relevant, a defined value list, a defined format and a defined unit. The intention is not to cover manufacturer-specific features.

Low-voltage switchgear and controlgear - Product data and properties for information exchange - Part 1: Catalogue data

LST EN IEC 60947-5-8:2021 低压开关设备和控制设备 第 5-8 部分：控制电路设备和开关元件 三位置启用开关（IEC 60947-5-8:2020）

Low-voltage switchgear and controlgear - Part 5-8: Control circuit devices and switching elements - Three-position enabling switches (IEC 60947-5-8:2020)

BS EN IEC 61439-1:2021 低压开关设备和控制设备组件 一般规则

Low-voltage switchgear and controlgear assemblies. General rules

DIN CLC IEC/TR 63216:2021 低压开关设备和控制设备. 开关设备和控制设备及其组件的电磁兼容评估(IEC/TR 63216-2019); 德文版 CLC IEC/TR 63216-2020

The purpose of this document is to define homogeneous categories for the electromagnetic environments in order to harmonize as far as practicable all general rules and product standard requirements of electromagnetic compatibility (EMC), applicable to low-voltage switchgear, cont

Low-voltage switchgear and controlgear - Electromagnetic compatibility assessment for switchgear and controlgear and their assemblies (IEC/TR 63216:2019); German version CLC IEC/TR 63216:2020

DIN EN IEC 61439-7:2021 低压开关设备和控制设备组件 第7部分：码头、露营地、集市广场、电动汽车充电站等特定应用的组件（IEC 61439-7:2018 + COR1:2019）；德文版 EN IEC 61439-7:2020

This standard applies for Low-voltage switchgear and controlgear assemblies for specific installations at public sites such as marinas, camping sites, market squares and similar applications and for charging stations for Electrical Vehicles.

Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations (IEC 61439-7:2018 + COR1:2019); German version EN IEC 61439-7:2020

DS/EN IEC 61439-2:2021 低压开关设备和控制设备组合件 第2部分：电力开关设备和控制设备组合件

Low-voltage switchgear and controlgear assemblies – Part 2: Power switchgear and controlgear assemblies

DS/EN IEC 61439-1:2021 低压开关设备和控制设备组合件 第1部分：总则

Low-voltage switchgear and controlgear assemblies – Part 1: General rules