31.220.10 插头和插座装置、连接器 标准查询与下载

GSO IEC 60512-4-1:2015 电子设备连接器 测试和测量 第4-1部分：电压应力测试 测试 4a：耐压

This part of IEC 60512, when required by the detail specification, is used for testing connectors of electronic equipment within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to determine the ability of a component to withstand specified test voltages applied in a specified manner. NOTE Standard conditions of testing are defined in Part 1 of this standard.

Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof

GSO IEC 60130-17:2015 频率低于 3 MHz 的连接器 第17部分：允许多向配合的互连设备的详细规范 用于可充电电池

This part of IEC 60130 is a connector detail specification for a battery interconnection system for portable computers, cellular telephones and other electronic devices requiring power not to exceed 50 V d.c. SELV (Safety Extra Low Voltage).

Connectors for frequencies below 3 MHz - Part 17: Detailspecification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries

GSO IEC 60512-15-5:2015 电子设备的连接 测试和测量 第15-5部分：连接（机械）测试 测试 15e：插入时的接触调整和电缆摇摆

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this document is to detail a standard test method to verify the capability of the contact retention system to withstand dynamic mechanical loading of the contacts that tends to dislodge them.

Connectors for electronic equipment - Tests and measurements - Part 15-5: Connector tests (mechanical) - Test 15e: Contact retention in insert, cable nutation

GSO IEC 60512-11-10:2015 电子设备连接器 测试和测量 第11-10部分：气候测试 测试 11j：寒冷

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to be stored and/or to function in a specified manner under specified conditions of cold.

Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold

GSO IEC 60512-11-9:2015 电子设备连接 测试和测量 第11-9部分：气候测试 测试 11(i)：干热

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to be stored and/or to function in a specified manner under specified conditions of dry heat.

Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat

GSO IEC 60512-16-1:2015 电子设备的连接 测试和测量 第16-1部分：触点和端子的机械测试 测试 16a：探针损坏

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the effectiveness of the elastic system of contacts to resist damage from the insertion of a specified test probe. Although this test is intended for cylindrical contacts, the use for contacts with other geometries is not excluded. In which case, the detail specification should contain sufficient detail, given under the Clause 5 f), to enable the test to be done.

Connectors for electronic equipment - Tests and measurements - Part 16-1: Mechanical tests on contacts and terminations - Test 16a: Probe damage

GSO IEC 61076-2-101:2015 电子设备连接器 产品要求 第2-101部分：圆形连接器 M12 螺钉锁定连接器的详细规范

This part of IEC 61076 describes M12 circular connectors typically used for industrial process measurement and control. These connectors consist of fixed and free connectors either rewireable or non-rewireable, with screw-locking. The connectors with glass to metal seal are fixed connectors only which consist of fixed glass to metal sealed styles with rewireable male contacts and are intermateable with corresponding free connectors according to this International Standard. Male connectors have round contacts ∅ 0,6 mm, ∅ 0,76 mm, ∅ 0,8 mm and ∅ 1,0 mm. The different codings prevent the mating of these coded male or female connectors to any other interfaces and cross-mating between the different codings. NOTE M12 is the dimension of the thread of the screw-locking mechanism of these circular connectors.

Connectors for electronic equipment - Product requirements - Part 2-101: Circular connectors - Detail specification for M12 connectors with screw-locking

GSO IEC 60512-14-6:2015 电子设备的连接 测试和测量 第14-6部分：泄漏测试 测试 14f：接口泄漏防护

This part of IEC 60512, when required by the detail specification, is used for testing connectors. It may also be used for similar devices when specified in a detail specification. It is particularly, but not exclusively, suitable for connectors with removable contacts. The object of this document is to detail a standard test method to assess the effectiveness of the interfacial sealing of a connector against ingress of water by exposure to low pressure whilst immersed in a salt solution. It is intended to assess the effectiveness of the interfacial sealing means of connectors. Further, if any wires or contacts are not fitted, it assesses the sealing of one cavity of a connector from another.

Connectors for electronic equipment - Tests and measurements - Part 14-6: Sealing tests - Test 14f: Interfacial sealing

GSO IEC 60512-11-4:2015 电子设备连接器 测试和测量 第11-4部分：气候测试 测试 11d：温度快速变化

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand rapid change of temperature in air such as might occur during storage, transportation and use.

Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature

GSO IEC 60512-6-2:2015 电子设备连接 测试和测量 零件编号 (6-2)：动态应力测试 测试 6B：冲击

1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand specified severities of bump.

Connectors for electronic equipment - Tests and measurements - Part 6-2: Dynamic stress tests - Test 6b: Bump

GSO IEC 60512-16-11:2015 电子设备的连接 测试和测量 第16-11部分：触点和端子的机械测试 测试 16k：无焊护套连接的断裂强度

This part of IEC 60512, when required by the detail specification, is used for testing electomechanical components within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to determine ability of a component to resist forces that might strip a wrapped connection from its post along the axis of the post. Such wrapped connections are described in IEC 60352-1. NOTE This test is considered as destructive to specimens used.

Connectors for electronic equipment - Tests and measurements - Part 16-11: Mechanical tests on contacts and terminations - Test 16k: Stripping force, solderless wrapped connections

GSO IEC 60512-11-11:2015 电子设备连接 测试和测量 第11部分 11：气候测试 测试 11(k)：低气压

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to be stored and/or to function in a specified manner under specified conditions of low air pressure, for example high altitude.

Connectors for electronic equipment - Tests and measurements - Part 11-11: Climatic tests - Test 11k: Low air pressure

GSO IEC 60512-1-1:2015 电子设备连接器 测试和测量 第1-1部分：一般检查 测试 1a：目视检查

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method for the visual examination of electromechanical components

Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination

GSO IEC 60512-6-1:2015 电子设备连接 测试和测量 零件编号 (6-1)：动态应力测试 测试 6a：加速 稳态

1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand specified severities of acceleration.

Connectors for electronic equipment - Tests and measurements - Part 6-1: Dynamic stress tests - Test 6a: Acceleration, steady state

GSO IEC 60130-6:2015 频率低于 3 MHz 的连接器 第6部分：带刀片触点的微型矩形多极连接器

This Recommendation covers a range of rectangular multipole connectors with blade contacts, with either solder type terminations or solderless terminations of the wrap type.

Connectors for frequencies below 3 MHz - Part 6: Rectangular miniature multipole connectors with blade contacts

GSO IEC 60512-11-14:2015 电子设备连接 测试和测量 第11-14部分：气候测试 测试 11p：单流气体腐蚀测试

This part of IEC 60512, when required by the detail specification, is used for testing of connectors for electronic equipment. This test may also be used for similar components when specified in a detail specification. The object of this test is to define a standard test method, Test 11p, to assess the effects of controlled corrosion in industrial atmospheres, in a specified concentration of polluted gas(es).

Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests - Test 11p: Flowing single gas corrosion test

GSO IEC 60512-12-4:2015 电子设备连接器 测试和测量 第12-4部分：焊接测试 测试 12d：耐焊接热、焊浴法

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the ability of a connector to withstand the heating stresses produced by a mass soldering operation.

Connectors for electronic equipment - Tests and measurements - Part 12-4: Soldering tests - Test 12d: Resistance to soldering heat, solder bath method

GSO IEC 60512-6-4:2015 电子设备连接 测试和测量 第6-4部分：动态应力测试 测试 6d：振动（正弦）

This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to withstand specified severities of sinusoidal vibration.

Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)

GSO IEC 60512-11-3:2015 电子设备连接 测试和测量 第11-3部分：气候测试 测试 11c：湿热 稳定状态

1.1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing electromechanical components within the scope of IEC technical committee 48. This test may also be used for similar devices when specified in a detail specification. The object of this test is to define a standard test method to assess the ability of components to be stored and/or to function in a specified manner under conditions of high relative humidity.

Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state

GSO IEC 61076-3-116:2015 电子设备连接器 产品要求 第3-116部分：矩形连接器 用于与八路屏蔽和无护套连接器一起使用的保护外壳的详细规范 频率高达 600 MHz 适用于包含电源链接口的工业环境

This part of IEC 61076 covers protective housings for upgrading existing 8-way shielded and unshielded connectors utilizing the interface described in IEC 60603-7-2, IEC 60603-7-3, IEC 60603-7-4, IEC 60603-7-5, and IEC 60603-7-7 to IP65 and IP67 ratings, according to IEC 60529, for use in industrial environments. The housings cover a variety of different locking mechanisms according to this International Standard and a variety of different mounting configurations and termination types which are detailed in IEC 60603-7. Common mating configuration for all variants are defined in IEC 60603-7. The mating dimensions for the housings under Clause 3 allow the mating conditions under IEC 60603-7 to be fulfilled. The fully assembled variants (connectors) described in this standard incorporate fixed and free connectors which are fully compliant with IEC 60603-7.

Connectors for electronic equipment - Product requirements - Part 3-116: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments