共找到 1356 条与 同轴电缆、波导和其他射频电缆 相关的标准,共 91 页
Coaxial communication cables - Part 9-2: Detail specification for 50-0,4 type RF flexible cables
What is BS IEC 61196 ‑ 1 ‑ 100 - General requirements for coaxial communication cables about? BS IEC 61196 is a series on coaxial communication cables. A coaxial communication cable is a type of electrical cable consisting of an inner conductor surrounded by a concentric conducting shield, with the two separated by a dielectric (insulating material); many coaxial cables also have a protective outer sheath or jacket. BS IEC 61196 ‑ 1 ‑ 100 gives the general requirements and conditions for electrical tests to be performed on coaxial communication cables and applies to IEC 61196-1-1xx (all parts), which specifies electrical test methods for coaxial communication cables. Further test details (for example, temperature, duration) and/or test requirements are given in BS IEC 61196 ‑ 1 ‑ 100 . A table with electrical test methods of the IEC 61196-1-1xx series is given in BS IEC 61196 ‑ 1
Coaxial communication cables - Electrical test methods. General requirements
Coaxial communication cables - Part 1-200: Environmental test methods - General requirements
Coaxial communication cables - Part 1-200: Environmental test methods - General requirements
Radio frequency connectors - Part 1-5: Electrical test methods - Rise time degradation
Specification for the testing of balanced and coaxial information technology cabling - Category 6 cords as specified in ISO/IEC 11801‑1. Blank detail specification
Coaxial communication cables - Part 1-100: Electrical test methods - General requirements
Coaxial communication cables - Part 1-100: Electrical test methods - General requirements
1 Scope This part of IEC 61935 is a blank detail specification describing cords which are compliant with category 6 cabling requirements, as specified in the ISO/IEC 11801‑1 . ISO/IEC 11801 and ISO/IEC 11801 series definitions and specifications referenced by this blank detail specification are currently covered by ISO/IEC 11801‑1. This document is intended to be used in conjunction with IEC 61935‑2, IEC 61156‑1, IEC 61156‑6, IEC 60603‑7‑41 and IEC 60603‑7‑51. The blank detail specification determines the layout and style for detail specifications describing cords with transmission characteristics up to 500 MHz for digital communications. Detail specifications, based on the blank detail specification, can be prepared by a national organization, a manufacturer, or a user. Test configuration applicable to cords is detailed in the IEC 61935‑2.
Specification for the testing of balanced and coaxial information technology cabling - Category 6A cords as specified in ISO/IEC 11801-1. Blank detail specification
Coaxial communication cables - Sectional specification for cables for BCT cabling in accordance with ISO/IEC 11801-4. Indoor drop cables for systems operating at 5 MHz. 6 000 MHz
Specification for the testing of balanced and coaxial information technology cabling - Part 2-21: Category 6 cords as specified in ISO/IEC 11801-1 - Blank detail specification
Specification for the testing of balanced and coaxial information technology cabling - Part 2-22: Category 6A cords as specified in ISO/IEC 11801-1- Blank detail specification
Passive RF and microwave devices, intermodulation level measurement - Part 2: Measurement of passive intermodulation in coaxial cable assemblies
Metallic cables and other passive components test methods. Electromagnetic compatibility (EMC). Extension of the frequency range to higher frequencies for transfer impedance and to lower frequencies for screening attenuation measurements using the triaxia
Metallic cables and other passive components test methods – Part 4-16: Electromagnetic compatibility (EMC) – Extension of the frequency range to higher frequencies for transfer impedance and to lower frequencies for screening attenuation measurements usin
Coaxial communication cables. Blank detail specification for CATV drop cables
Coaxial communication cables. Sectional specification for CATV drop cables
Coaxial communication cables – Part 6: Sectional specification for CATV drop cables
Coaxial communication cables – Part 7: Sectional specification for cables for BCT cabling in accordance with ISO/IEC 11801-4 – Indoor drop cables for systems operating at 5 MHz – 6 000 MHz
Coaxial communication cables – Part 6-1: Blank detail specification for CATV drop cables
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号