33.180.30 光纤放大器 标准查询与下载

BS EN 61290-3-3:2014 光学放大器.试验方法.信号功率与总ASE功率比

Optical amplifiers. Test methods. Noise figure parameters. Signal power to total ASE power ratio

EN 61290-3-3:2014 光放大器 测试方法 第 3-3 部分：噪声系数参数 信号功率与总 ASE 功率之比

IEC 61290-3-3:2013 applies to all commercially available single channel optical amplifiers (OAs), including OAs using optically pumped fibres (OFAs) based on either rare-earth doped fibres or on the Raman effect, semiconductor optical amplifier modules (SOA modules) and planar optical waveguide amplifiers (POWAs). More specifically, it applies to single channel OAs placed before optical receivers, where there are no optical bandpass filtering elements placed between the OA and the receiver. The object of this part of IEC 61290-3 is to establish uniform requirements for accurate and reliable measurement of the ratio of the signal output power to the total ASE power generated by the OA in the optical bandwidth of the receiver. This quantity is a measure of the spontaneous-spontaneous beat noise at the receiver, and is correlated to the spontaneous-spontaneous noise factor of the OA, Fsp-sp, as defined in IEC 61290-3 and IEC 61291-1. Keywords: single channel optical amplifiers (OAs), semiconductor optical amplifier modules (SOA modules), planar optical waveguide amplifiers (POWAs), measurement of the ratio of the signal output power to the total ASE power generated by the OA in the optical bandwidth of the receiver

Optical amplifiers - Test methods - Part 3-3: Noise figure parameters - Signal power to total ASE power ratio

GSO IEC 61291-6-1:2013 光放大器 第6-1部分：接口 命令集

IEC 61291-6-1:2008 describes the optical amplifier command set (OACS) for use in communicating with and controlling intelligent optical amplifiers. These amplifiers can receive and possibly respond to such commands by using resident firmware or may be optical amplifiers controlled by a microprocessor. This standard addresses the structure and content of the command set to control optical amplifiers. It does not cover the physical or hardware interface, which is assumed to exist for communication of this command set to the optical amplifier.

Optical amplifiers - Part 6-1: Interfaces - Command set

JIS C 6122-4-2:2013 光纤放大器 试验方法 第4-2部分 瞬态参数 使用宽带源法测量增益参数

Optical amplifiers -- Test methods -- Part 4-2: Transient parameters -- Measurement of gain parameters using broadband source method

JIS C 6122-4-1:2013 光学放大器.试验方法.第4-1部分:瞬态参数.使用双波长法测量增益参数

Optical amplifiers.Test methods.Part 4-1: Transient parameters.Measurement of gain parameters using two-wavelength method

JIS C 6121-6-1:2013 光学放大器.第6-1部分:接口.指令集

Optical amplifiers -- Part 6-1: Interfaces -- Command set

IEC TR 61292-9:2013 光放大器第9部分:半导体光放大器

Optical amplifiers - Part 9: Semiconductor optical amplifiers (SOAs)

IEC 61290-3-3:2013 光放大器. 试验方法. 第3-3部分: 噪声指数参数. 信号功率与总ASE功率比

Optical amplifiers - Test methods - Part 3-3: Noise figure parameters - Signal power to total ASE power ratio

BS EN 62343:2013 动态模块. 总则和指引

Dynamic modules. General and guidance

GSO IEC 62343-1-2:2013 动态单元 第1-2部分：标准性能规格 用于受控环境（C 类）的带编织带的动态色散补偿装置

This part of IEC 62343 contains the minimum initialisation test and measurement requirements and severities, which an optical dynamic chromatic dispersion compensator (DCDC) shall satisfy in order to be categorised as meeting the requirements of DCDC used in controlled environments. The requirements cover optical dynamic chromatic dispersion compensators for Category C – Controlled environments.

Dynamic modules - Part 1-2: Performance standards - Dynamic chromatic dispersion compensator with pigtails for use in controlled environments (Category C)

GSO IEC 61290-1-1:2013 光放大器 测试方法 第1-1部分：功率和增益参数 光谱分析仪方法

This International Standard applies to all commercially available optical amplifiers (OAs) and optically amplified modules. It applies to OAs using optically pumped fibers (OFAs based on either rare-earth doped fibers or on the Raman effect), semiconductor OAs (SOAs) and waveguides (POWAs). The object of this standard is to establish uniform requirements for accurate and reliable measurements, by means of the optical spectrum analyzer test method, of the following OA parameters, as defined in IEC 61291-1: a) nominal output signal power; b) gain; c) reverse gain; d) maximum gain; e) maximum gain wavelength; f) maximum gain variation with temperature; g) gain wavelength band; h) gain wavelength variation; i) gain stability; j) polarization-dependent gain; k) large-signal output stability; l) saturation output power; m) maximum input signal power; n) maximum output signal power; o) input power range; p) output power range; q) maximum total output power. NOTE All numerical values followed by (‡) are suggested values for which the measurement is assured. Other values may be acceptable but should be verified. The object of this standard is specifically directed to single-channel amplifiers. For multichannel amplifiers, one should refer to the IEC 61290-10 series.

Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method

DIN EN 62343-1-3:2013 动态模块.第1-3部分:性能标准.动态增益倾斜均衡器(非连接化)(IEC 62343-1-3-2012).德文版本EN 62343-1-3-2013

Dynamic modules - Part 1-3: Performance standards - Dynamic gain tilt equalizer (non-connectorized) (IEC 62343-1-3:2012); German version EN 62343-1-3:2013

DIN IEC/TR 62343-6-2:2013 动态模型.第6-2部分:软件和硬件接口.调查结果(IEC 86C/1124/DTR-2013)

Dynamic modules - Part 6-2: Software and hardware interfaces - Survey results (IEC 86C/1124/DTR:2013)

BS EN 62343-1-3:2013 动态模块.性能标准.动态增益倾斜均衡器(非连接化)

Dynamic modules. Performance standards. Dynamic gain tilt equalizer (non-connectorized)

DIN IEC/TR 61292-9:2013 光放大器 第9部分 半导体光放大器(SOAs)(IEC 86C/1109/CD-2013)

Optical amplifiers - Part 9: Semiconductor optical amplifiers (SOAs) (IEC 86C/1109/CD:2013)

DIN EN 62148-3 Berichtigung 1:2013 光纤有源元件及器件.包装和接口标准.第3部分:SFF 20-针收发器(IEC 62148-3-2010).德文版本EN 62148-3-2011,DIN EN 62148-3:2011-06标准的勘误表.EN 62148-3-2011标准的德文版本CENELEC-Cor.-2011

Fibre optic active components and devices - Package and interface standards - Part 3: SFF 20-pin transceivers (IEC 62148-3:2010); German version EN 62148-3:2011, Corrigendum to DIN EN 62148-3:2011-06; German version CENELEC-Cor. :2011 to EN 62148-3:2011

DIN EN 61291-1:2013 光纤放大器.第1部分:通用规格(IEC 61291-1-2012).德文版本EN 61291-1-2012

Optical amplifiers - Part 1: Generic specification (IEC 61291-1:2012); German version EN 61291-1:2012

NF C93-802-1:2012 光学放大器 - 第1部分: 一般规范

Optical amplifiers - Part 1: generic specification

JIS C 6122-10-4:2012 光纤放大器.试验方法.第10-4部分:多通道参数.用光谱分析仪的内插辐射体减少法

Optical amplifiers -- Test methods -- Part 10-4: Multichannel parameters -- Interpolated source subtraction method using an optical spectrum analyzer

LST EN 61291-1-2012 光放大器 第1部分：通用规范（IEC 61291-1:2012）

Optical amplifiers -- Part 1: Generic specification (IEC 61291-1:2012)