43.080.10 卡车和挂车 标准查询与下载
共找到 265 条与 卡车和挂车 相关的标准，共 18 页
Rear underrun protection for trucks and trailers
- ICS
- 43.080.10
- CCS
- 发布
- 2016-11-15
- 实施
This European Standard applies to body structures on commercial vehicles and on trailers. This European Standard sets out basic minimum requirements for standard vehicle bodies (side walls, front and rear walls) and for reinforced vehicle bodies and specifies appropriate tests. This European Standard applies to all commercial vehicles which are related by design and body type to the body structures described below. Forces applied according to the test requirements described below can be invoked for load securing purposes. The floor of the vehicle is a part of the sub frame. As long as the floor strength is not defined, the manufacturer should give the necessary information. Testing of the axle load on the floor should be carried out analogous to EN 283. The result should be marked in locations according to chapter 6. This European Standard does not apply to vans according to ISO 27956.
Securing of cargo on road vehicles - Body structure of commercial vehicles - Minimum requirements
- ICS
- 43.080.10
- CCS
- T09
- 发布
- 2016-11
- 实施
BS EN 16972. Road vehicles. Carrying vehicles for swap bodies class C, swap tanks class C and 20' ISO containers. Interface dimensions
- ICS
- 43.080.10
- CCS
- 发布
- 2016-02-22
- 实施
- 2016-02-22
This Specification Covers the Minimum Technical Requirements for the design, construction, inspection and testing of the Fuel Road Tanker (covering Vehicle, Chassis and its Super Structure etc.) intended for transportation of all petroleum products including all grades of gasoline such as Gasoline (UN 1203), Gas oil (UN 1202) and Kerosene (UN 1223) & Euro IV Products across Kuwait.
Fuel road tanker for transportation of petroleum products
- ICS
- 43.080.10
- CCS
- 发布
- 2015-12-21
- 实施
This SAE Recommended Practice covers the design and application of a 120 VAC single phase engine based auxiliary power unit or GENSET. This document is intended to provide design direction for the single phase nominal 120 VAC as it interfaces within the truck architecture providing power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off.
Auxiliary Power Unit Electrical Interface Requirements for Class Eight Trucks
- ICS
- 43.080.10
- CCS
- 发布
- 2015-12-01
- 实施
- 2015-12-24
Tank trucks - Grounding plate - Dimensions
- ICS
- 43.080.10
- CCS
- T58
- 发布
- 2015-12
- 实施
Road tankers - Dipstick assembly - Mating dimensions
- ICS
- 43.080.10
- CCS
- T58
- 发布
- 2015-10
- 实施
LPG equipment and accessories - Inspection and testing of LPG road tankers
- ICS
- 43.080.10
- CCS
- 发布
- 2015-03-16
- 实施
- 2015-03-16
LPG equipment and accessories - Inspection and testing of LPG road tankers; German version EN 14334:2014
- ICS
- 43.080.10
- CCS
- T58;E98
- 发布
- 2015-01
- 实施
Automobile vehicles for transportation of food liquids. Technical requirements and test methods
- ICS
- 43.080.10
- CCS
- T43
- 发布
- 2015
- 实施
- 2017-04-01
LPG equipment and accessories. Inspection and testing of LPG road tankers
- ICS
- 43.080.10
- CCS
- T58
- 发布
- 2014-11-30
- 实施
- 2014-11-30
This European Standard specifies minimum requirements for the inspection and testing of the LPG road tanker, which includes its pressure vessel, accessories and vehicle LPG equipment. This European Standard does not specify requirements for the initial inspection (after manufacture) of a pressure vessel, see EN 12493, or for service equipment on the road tanker, see EN 12252. This European Standard does not apply to compartmented road tankers. NOTE 1 There is no upper size limit for the pressure vessel as this will be determined by the gross vehicle weight limitation. NOTE 2 For inspection and testing requirements of equipment other than the pressure vessel, accessories and vehicle LPG equipment, see applicable regulations.
LPG equipment and accessories - Inspection and testing of LPG road tankers
- ICS
- 43.080.10
- CCS
- T58
- 发布
- 2014-11
- 实施
LPG equipment and accessories - Equipping of LPG road tankers
- ICS
- 43.080.10
- CCS
- 发布
- 2014-07-31
- 实施
- 2014-07-31
LPG equipment and accessories - Equipping of LPG road tankers; German version EN 12252:2014
- ICS
- 43.080.10
- CCS
- E98
- 发布
- 2014-07-01
- 实施
This SAE Standard outlines the requirements for a preformed thermosetting hose intended for use in heavy-duty vehicle engines, such as air cleaner to carburetor hose, where it is exposed to normal heat and splash of motor oil.
General Requirement for Preformed Hoses for Air Induction on Heavy-Duty Engines
- ICS
- 43.080.10
- CCS
- J93
- 发布
- 2014-06-04
- 实施
This SAE Standard includes spur gear and direct drive type hand-cranked winches as used on boat trailers. This does not include brake type winches as used in boat lift, davit, or industrial applications.
Hand Winches-Boat Trailer Type
- ICS
- 43.080.10
- CCS
- U10
- 发布
- 2014-06-02
- 实施
LPG equipment and accessories. Equipping of LPG road tankers
- ICS
- 43.080.10
- CCS
- T58
- 发布
- 2014-04-30
- 实施
- 2014-04-30
