47.020.20 船用发动机和推进系统 标准查询与下载

KS V 0411-2019 船舶推进机械输出的术语和定义

Terminology and definition of output ofpropulsion machinery installed in ships

T/ZZB 1474-2019 舷外机

本标准规定了舷外机的术语和定义、结构和分类、基本要求、技术要求、试验方法、检验规则、包装、运输、贮存和质量承诺。 本标准适用于以汽油机为动力，标定功率 7.5 kW～110 kW 的舷外机。 

Outboard engine

CB/Z 811-2019 海洋工程环境模拟与环境载荷预报方法

Ocean Engineering Environmental Simulation and Environmental Load Forecasting Method

ASTM F1338-91(2019) 主要推进中速船用柴油发动机标准指南涵盖性能和最小装配范围

1.1 This guide covers performance and minimum scope of assembly of all medium speed marine diesel engines intended for main propulsion of single or multiple screw propelled marine vessels or for vessels using other than screw propellertype main propulsion. 1.2 This guide is intended to supplement the regulations of legally constituted regulating authorities. In the event of any conflict, which may become apparent after publication of this guide, with such legally constituted regulations, the latter shall take precedence, as may be applicable within the jurisdiction of such authorities and specific to each case, unless such latter regulations are formally waived by proper cognizant authority. 1.3 This guide is not intended to relieve the purchaser of the obligation fully to advise the engine builder of all of the purchaser’s unique operational considerations to allow those considerations to be satisfied. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Main Propulsion Medium Speed Marine Diesel Engines Covering Performance and Minimum Scope of Assembly

KS V 4017-2019 船用螺旋桨定距和调距螺旋桨

Screw type fixed pitch and controllable pitch propellers for ship

KS V 7825-2019 船用柴油机的进气阀和排气阀

Inlet valves and exhaust valves for marine diesel engines

KS V 7228-2019 船用平面和圆柱形视镜

Flat and cylindrical sight glasses for marine use

KS V 7831-2019 缸径230mm以下小型船用发动机气缸套

Cylinder liners for small size marine engines with cylinder bore 230 mm or less

BS ISO 20233-2:2019 船舶和海洋技术 船舶设计中螺旋桨空化噪声评估模型试验方法噪声源定位

What is ISO 20233-2 -  Noise source localization  about?    ISO 20233-2  is the second part of the  ISO 20233  series of standards that   specifies a model test method for propeller cavitation noise evaluation in ship design, focusing mainly on noise source localization. The procedure comprises the model test set-up, noise measurements, data processing and source localization. The target noise source being propeller cavitation,  ISO 20233-2  describes the test set-up and conditions to reproduce the cavitation patterns of the ship, which is the same as in  ISO 20233-1 . The noise measurements are performed using a hydrophone array for the source localization. Therefore, the instrumentation of the hydrophone array is also addressed, as well as a suitable array signal processing of the measured data. Finally, a method to visualize and interpret the results is presented.

Ships and marine technology. Model test method for propeller cavitation noise evaluation in ship design - Noise source localization

ISO 20233-2:2019 船舶和海上技术.船舶设计中螺旋桨空化噪声评估的模型试验方法.第2部分:噪声源定位

This document specifies a model test method for propeller cavitation noise evaluation in ship design, focusing mainly on the noise source localization. The procedure comprises the model test set-up, noise measurements, data processing and source localization. The target noise source being propeller cavitation, this document describes the test set-up and conditions to reproduce the cavitation patterns of the ship, which is the same as in ISO 20233-1. The noise measurements are performed using a hydrophone array for the source localizations. Therefore, the instrumentation of the hydrophone array is also addressed, as well as a suitable array signal processing of the measured data. Finally, a method to visualize and to interpret the results is presented.

Ships and marine technology — Model test method for propeller cavitation noise evaluation in ship design — Part 2: Noise source localization

ASTM F1134-15(2019) 船用电动机和发电机绝缘电阻监视器的标准规范

1.1 This specification covers monitoring devices (monitors) for the automatic detection and signaling of low insulation resistance values in idle electrical motors or generators, or both. 1.2 Monitors are intended for permanent installation in both existing or new panels and controller enclosures designed for marine application. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Insulation Resistance Monitor for Shipboard Electrical Motors and Generators

BS ISO 20083-3:2019 船舶和海洋技术 通过测量轴扭曲确定船舶推进系统的轴功率 弹性振动法

What is ISO 20083-3 -  Shaft power of   ship propulsion systems  about?    ISO 20083-3  is the third part of the  ISO 20083  series of standards that   specifies a procedure to determine the shaft power of engine ships, by measuring the   shaft distortion using an elastic vibration type device.  ISO 20083-3  gives the principles of the measurement, the components of the device and the calculation method.  ISO 20083-3  also describes the factors for determining the measuring accuracy and specifies the on-board documentation for the device.   ...

Ships and marine technology. Determination of the shaft power of ship propulsion systems by measuring the shaft distorsion - Elastic vibration method

BS ISO 20083-2:2019 船舶和海洋技术 通过测量轴畸变确定船舶推进系统的轴功率 光学反射法

What is ISO 20083-2 -  Shaft power of   ship propulsion systems  about?    ISO 20083-2  is the second part of the  ISO 20083  series of standards that   specifies a procedure to determine the shaft power of engine ships, by measuring the shaft distortion using an optical reflection type device.    ISO 20083-2  gives the principles of the measurement, the components of the device, and the calculation method.  ISO 20083-2  also describes the factors for determining the measuring accuracy, including the calibration procedure, and specifies the on-board documentation for the device.

Ships and marine technology. Determination of the shaft power of ship propulsion systems by measuring the shaft distorsion - Optical reflection method

ISO 20083-3:2019 船舶和航海技术.通过测量轴变形测定船舶推进系统的轴功率.第3部分:弹性振动法

This document specifies a procedure to determine the shaft power of engine ships, by measuring the shaft distortion using an elastic vibration type device. It gives the principles of the measurement, the components of the device and the calculation method. It also describes the factors for determining the measuring accuracy and specifies the on-board documentation for the device.

Ships and marine technology — Determination of the shaft power of ship propulsion systems by measuring the shaft distorsion — Part 3: Elastic vibration method

ISO 20083-2:2019 船舶和航海技术.通过测量轴变形测定船舶推进系统的轴功率.第2部分:光学反射法

This document specifies a procedure to determine the shaft power of engine ships, by measuring the shaft distortion using an optical reflection type device. It gives the principles of the measurement, the components of the device and the calculation method. It also describes the factors for determining the measuring accuracy, including the calibration procedure, and specifies the on-board documentation for the device.

Ships and marine technology — Determination of the shaft power of ship propulsion systems by measuring the shaft distorsion — Part 2: Optical reflection method

CB/T 3892-2019 救生艇轴系技术条件

Lifeboat Shafting Specifications

ASTM F1718-01(2019) 旋转正排量蒸馏燃料泵的标准规范

1.1 This specification covers the requirements applicable to the design and construction of rotary positive displacement distillate fuel pumps for shipboard use. 1.2 Lineal dimensions and units of force in this specification are expressed as inches and pounds respectively. A companion metric standard is in the process of preparation. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

KS V 0420-2019 船用主机和发电机润滑油系统

Main and generator engine lubricating oil system for marine use

ASTM F2361-18 船用低压（1000 VAC或以下）交流电动机订购的标准指南—；不超过500马力的电动机

1.1 This guide covers the required basic ordering information for low voltage (1000 VAC or less) general-purpose, commercial, universal, small-, and medium-sized alternating current electric motors for shipboard use, up to and including motors of 500 hp. 1.2 The electric motors covered by this guide are generalpurpose (GP) motors intended to drive common shipboard mechanical machinery such as fans, blowers, centrifugal and screw pumps. 1.3 This guide is not intended to be used to order specialpurpose (SP) motors or definite-purpose motors (for example, cryogenic service) or motors for use in hazardous (classified) locations as defined by the National Electrical Code (NFPA 70). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower

ASTM F2798-09(2018) 用于船舶应用的带油浸马达的无密封润滑油泵的标准规范

1.1 This specification defines the requirements applicable to design, construction and testing of sealless, rotary positive displacement pumps with oil-through motors for ship lubricating oil service. The complete pump and motor assembly is referred to as canned lube oil pump (CLP). This specification applies to CLPs pumping oil with a SAE rating of 20–50. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications