47.020.50 甲板设备和装置 标准查询与下载

ISO/FDIS 5694 船舶和海洋技术 甲板覆盖物

Ships and marine technology — Deck covering

ISO/PRF 9519:2023 船舶和航海技术 单梯级和狗步梯梯级

Ships and marine technology — Single rungs and rungs for dog-step ladders

ISO/DIS 9519 船舶和海洋技术 单梯级和狗梯梯级

Ships and marine technology — Single rungs and rungs for dog-step ladders

ISO 4864:2023 船舶和航海技术 自升式装置上的升降系统设备 一般要求

Ships and marine technology — Jacking system appliances on self-elevating unit — General requirements

ISO 4862:2023 船舶和海洋技术 耙吸式挖泥船绞车

Ships and marine technology — Winches for trailing suction hopper dredger

BS ISO 4857:2023 船舶和海洋技术 锚机和绞车的测试程序和方法

1   Scope This document specifies procedures and methods for the factory acceptance test for the complete set of windlass and winch system, which is performed after the equipment is assembled. The test methods and procedures specified in this document apply to windlasses and winches.

Ships and marine technology. Test procedures and methods for windlasses and winches

BS ISO 4853:2023 船舶和海洋技术 A型架发射和回收系统

1   Scope This document specifies the design, operation, performance and acceptance test of A-frame launch and recovery systems (hereinafter referred to as “ A-frame LARS ”) for underwater applications excluding lifesaving appliances. This document is applicable to the design, manufacturing, testing and acceptance of A-frame LARS for underwater applications excluding lifesaving appliances.

Ships and marine technology. A-frame launch and recovery system

ASTM F2935-23 巴拿马系泊铸钢楔块标准规范

1.1 This specification covers the principal dimensions and materials of chocks installed in ships to comply with the regulations of the Panama Canal. 1.2 Chocks can be used with either wire rope or fiber and synthetic ropes. 1.3 Chocks are for mounting directly on a deck, seat (foundation) or for mounting in a bulwark. 1.4 To meet Panama Canal Company regulations the radius of contact surfaces of lines must be 180 mm. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chocks, Panama, Mooring Cast Steel

ASTM F2936-23 铸钢船舶系泊用楔块标准规范

1.1 This specification covers the principal dimensions and materials of closed chocks for installation on ships used for mooring. 1.2 Chocks can be used with either wire rope or fiber and synthetic ropes. 1.3 Chocks are for mounting directly on a deck, seat (foundation), or for mounting in a bulwark. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chocks, Ship Mooring, Cast Steel

ISO/FDIS 4864 船舶与航海技术《自升式平台上的升降系统装置》通用要求

Ships and marine technology — Jacking system appliances on self-elevating unit — General requirements

ISO/FDIS 4861 船舶与海洋技术 打桩驳船绞车

Ships and marine technology — Piling barge winches

ISO/PRF 4857 船舶与航海技术—起锚机和绞车的试验程序和方法

Ships and marine technology — Test procedures and methods for windlasses and winches

ISO 4857:2023 船舶和海洋技术 锚机和绞车的测试程序和方法

This document specifies procedures and methods for the factory acceptance test for the complete set of windlass and winch system, which is performed after the equipment is assembled. The test methods and procedures specified in this document apply to windlasses and winches.

Ships and marine technology — Test procedures and methods for windlasses and winches

ISO 5528:2023 船舶及航海技术 深海液压绞车设备

This document specifies requirements for the design, manufacture, operation, safety, performance, acceptance tests and designation system of deep-sea hydraulic winch equipment (hereafter referred to as “winch equipment”). The deep-sea hydraulic winch equipment are intended to be used for large load deep-sea operations in depths of 3000 m to 11000 m.

Ships and marine technology — Deep-sea hydraulic winch equipment

ISO 4853:2023 船舶和海洋技术 A 型架发射和回收系统

This document specifies the design, operation, performance and acceptance test of A-frame launch and recovery systems (hereinafter referred to as “A-frame LARS”) for underwater applications excluding lifesaving appliances. This document is applicable to the design, manufacturing, testing and acceptance of A-frame LARS for underwater applications excluding lifesaving appliances.

Ships and marine technology — A-frame launch and recovery system

ISO/PRF 24681 船舶和海洋技术 纤维增强塑料格栅

Ships and marine technology — Fibre-reinforced plastic gratings

ISO/PRF 5528 船舶与海洋技术—深海液压绞车设备

Ships and marine technology — Deep-sea hydraulic winch equipment

ISO/FDIS 4862 船舶与海洋技术 绞吸式绞吸式挖泥船

Ships and marine technology — Winches for trailing suction hopper dredger

ISO 24681:2023 船舶和海洋技术 纤维增强塑料格栅

This document specifies the structure, technical requirements and test methods of gratings for fibre- reinforced plastics (FRP) in the marine industry. It also defines terms related to FRP gratings. This document is applicable to the design, manufacture and inspection of self-support FRP gratings used for pedestrian pathways and platforms on ships or offshore platforms.

Ships and marine technology — Fibre-reinforced plastic gratings

ISO/DIS 5489 船舶与航海技术 登船梯

Ships and marine technology — Embarkation ladders