47.020.60 船舶和海上构筑物用电气设备 标准查询与下载

ASTM F1836M-15(2019) 填料管 尼龙和包装组件的标准规格（公制）

1.1 This specification covers the general requirements for nylon stuffing tubes and packing assemblies. Nylon stuffing tubes are intended for making electric cable penetrations in marine shipboard enclosures for electrical equipment. The following types are suitable for both thin-wall enclosures up to 5 mm (3⁄16 in.) thick and thick-wall enclosures, bulkheads, and decks of 5 to 19 mm (3⁄16 to 3⁄4 in.) thick. 1.2 This specification does not cover metal stuffing tubes. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Stuffing Tubes, Nylon, and Packing Assemblies (Metric)

T/CEC 198-2019 低压岸电连接系统（LVSC系统）用插头插座和船用耦合器

本标准规定了岸电设备连接接口的技术要求、 试验检测方法、 功能定义、 结构及尺寸。 本标准适用于岸电设备连接接口， 其额定电压不超过1000V(AC）， 频率50Hz/60 Hz，额定电流不超过350A。

Plug sockets and marine couplers for low-voltage shore connection systems (LVSC systems)

T/CEC 199-2019 船岸连接电缆管理系统技术条件

本标准规定了船岸连接电缆管理系统的一般要求、技术要求、试验方法、检验规则、标志、包装和运输。 本标准适用于沿海和内河新建、改造港口码头的船岸连接电缆管理系统，低压传输电压为400V 450V、高压传输电压为6kV～11kV。

Specifications for ship-shore connection cable management system

IEC 61892-5:2019 移动和固定海上单位 - 电气安装 - 第5部分:移动单元

Mobile and fixed offshore units - Electrical installations - Part 5: Mobile units

IEC 61892-7:2019 移动和固定海上单位 - 电气安装 - 第7部分:危险区域

Mobile and fixed offshore units - Electrical installations - Part 7: Hazardous areas

IEC 61892-1:2019 移动式和固定式海上装置.电气装置.第1部分:一般要求和条件

Mobile and fixed offshore units - Electrical installations - Part 1: General requirements and conditions

IEC 61892-6:2019 移动和固定海上设备 - 电气安装 - 第6部分:安装

Mobile and fixed offshore units - Electrical installations - Part 6: Installation

IEC 61892-1:2019 RLV 移动式和固定式海上装置.电气装置.第1部分:一般要求和条件

Mobile and fixed offshore units - Electrical installations - Part 1: General requirements and conditions

IEC 61892-3:2019 移动和固定海上设备 - 电气设备 - 第3部分:设备

"This part of IEC 61892 is applicable to electrical equipment in mobile and fixed offshore units including pipeline@ pumping or ""pigging"" stations@ compressor stations and single buoy moorings@ used in the offshore petroleum industry for drilling@ production@ accommodation@ processing@ storage and offloading purposes. It applies to all installations@ whether permanent@ temporary@ transportable or hand-held@ to AC installations and DC installations without any voltage level limitation. Referenced equipment standards may give voltage level limitations. This document specifies requirements such as those concerning ?C enclosures@ with regard to material@ marking (nameplates and labels)@ ventilation@ earthing@ EMC and short-circuit rating of components@ and ?C specific requirements related to use in an offshore unit@ such as ? generators and motors@ ? transformers@ ? switchgear and control gear assemblies@ ? instrumentation of power sources@ ? semiconductor converters@ ? secondary cells and batteries@ ? luminaires@ ? communication equipment@ ? control and instrumentation@ and ? accessories for accommodation and similar areas. This document does not apply to ?C fixed equipment for medical purposes@ ?C electrical installations of tankers@ and ?C control of ignition sources other than those created by electrical equipment. NOTE 1 For medical rooms@ IEC 60364-7-710 provides specific requirements. Requirements for tankers are given in IEC 60092-502. NOTE 2 Specific requirements in relation to electrical equipment in hazardous areas are given in IEC 61892-7. NOTE 3 Guidance on protection of non-electrical equipment can be found in ISO 80079-36@ ISO 80079-37 and IMO 2009 MODU Code@ 6.7."

Mobile and fixed offshore units - Electrical installations - Part 3: Equipment

IEC 61892-2:2019 移动和固定海上单位 - 电气安装 - 第2部分:系统设计

"This part of IEC 61892 is applicable to system design of electrical installations and equipment in mobile and fixed offshore units including pipeline@ pumping or ""pigging"" stations@ compressor stations and single buoy moorings@ used in the offshore petroleum industry for drilling@ production@ accommodation@ processing@ storage and offloading purposes. It applies to all installations@ whether permanent@ temporary@ transportable or hand-held@ to AC installations and DC installations@ without any voltage level limitation. Referenced equipment standards may give voltage level limitations. This document specifies requirements such as those concerning ?C sources of electrical power for manned and unmanned units@ ?C system earthing@ both for low-voltage and high-voltage installations@ ?C interface for electric transmission systems with power supplied from shore@ between interconnected offshore units@ and with power supplied by offshore units to subsea installations@ ?C distribution systems@ ?C cables and wiring systems@ ?C system studies and calculations@ ?C protection against electrical faults@ ?C lighting@ ?C energy control@ monitoring and alarm systems@ and ?C turret/swivel. This document gives information and guidance on topics such as ?C applicable examples of HVDC VSC technology@ and ?C guidelines for illumination level. This document does not apply to ?C fixed equipment for medical purposes@ ?C electrical installations of tankers@ and ?C control of ignition sources other than those created by electrical equipment. NOTE 1 For medical rooms@ IEC 60364-7-710 provides specific requirements. Requirements for tankers are given in IEC 60092-502. NOTE 2 Guidance on protection of non-electrical equipment can be found in ISO 80079-36@ ISO 80079-37 and IMO 2009 MODU Code@ 6.7."

Mobile and fixed offshore units - Electrical installations - Part 2: System design

IEC/IEEE 80005-1-2019 端口中的实用连接 - 第1部分:高压岸连接（HVSC）系统 - 一般要求

Utility connections in port — Part 1: High voltage shore connection (HVSC) systems — General requirements

IEC/IEEE 80005-1-2019 RLV 港口公用设施连接.第1部分:高压岸上连接（HVSC）系统.一般要求

Utility connections in port - Part 1: High voltage shore connection (HVSC) systems - General requirements

IEC/IEEE 80005-1:2019 RLV 港口公用设施连接.第1部分:高压岸上连接（HVSC）系统.一般要求

Utility connections in port - Part 1: High voltage shore connection (HVSC) systems - General requirements

ASTM F2044-09(2019)e1 液位指示设备 电气标准规范

1.1 This specification covers the requirements for electrical liquid level indicating equipment for shipboard low pressure and high pressure tanks containing freshwater, feed water, potable water, seawater, wastewater, diesel fuel, lubricating oil, contaminated oil, refrigerants, JP fuels, and various other fluids. Application includes compensating tanks in which the equipment must locate the interface. 1.2 Each liquid level indicating equipment typically consists of the following components: (a) One or more sensing devices; (b) Flexible interconnections, if needed; (c) Primary indicator panel assembly; (d) Auxiliary indicator panel assembly, when required; and (e) Portable indicator panel assembly, when required. 1.3 Special requirements for naval shipboard applications are included in the Supplementary Requirements section to this specification. 1.4 The values stated in SI units are to be regarded as standard. Inch-pound units are provided for information only and are not considered standard. Where information is to be specified, it shall be stated in SI units. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Liquid Level Indicating Equipment, Electrical

KS V IEC PAS 63108-2019 船舶电气装置一次直流配电系统设计架构

Electrical installations in ships — Primary DC distribution — System design architecture

KS V IEC PAS 63108:2019 船舶电气装置一次直流配电系统设计架构

Electrical installations in ships — Primary DC distribution — System design architecture

ASTM F681-82(2018) 使用分支连接的标准做法

Standard Practice for Use of Branch Connections

ASTM F1669M-12(2018) 船用电力系统绝缘监视器标准规范[公制]

1.1 This specification covers two (2) types of electrical system insulation monitoring devices. 1.1.1 Type I is an AC device intended as a permanently installed unit for use in the detection of ohmic insulation faults to ground in active AC ungrounded electrical systems up to 1000 VAC, having DC components up to 1500 VDC. 1.1.2 Type II is a DC device intended as a permanently installed unit for use in the detection of ohmic insulation faults to ground in DC ungrounded electrical systems up to 1500 VDC. 1.2 Limitations—This specification does not cover devices that are intended for operation in AC ungrounded systems without DC components. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are included for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test methods portion, Section 7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Insulation Monitors for Shipboard Electrical Systems [Metric]

IEC 60092:2024 SER 船舶电气装置-所有零件

Electrical installations in ships - ALL PARTS

KS V 8018-2017 船用电器水密试验方法

Method of watertight testing for marine electric appliances