47.020.99 有关造船和海上构筑物的其他标准 标准查询与下载

T/CHIDA 03-2023 耙头智能感知系统技术要求

本文件规定了智能耙头感知系统的组成、接口、功能和性能。 本文件适用于耙吸挖泥船智能耙头感知系统的设计、制造、改造和验收。

Technical requirements for draghead intelligent sense system

T/CHIDA 06-2023 绞吸挖泥船绞刀

本文件规定了绞吸挖泥船绞刀的技术要求、试验方法、检验、标志、包装、运输、贮存等。 本文件适用于吸管内径大于500mm的绞吸挖泥船绞刀的设计、制造和检验，修理可参照执行。

Cutter head of cutter suction dredger

ISO 24452:2023 船舶和海洋技术.极地水中使用的个人和团体生存工具包

Ships and marine technology — Personal and group survival kit for use in polar water

JT/T 1468-2023 耙吸挖泥船耙臂随动架技术要求

本标准适用于耙吸挖泥船随动架的设计、制造。

Technical requirements for rake arm follower frame of rake suction dredger

ISO 23668:2022 船舶和海洋技术.海洋环境保护.船上pH连续监测方法

This document specifies the performance requirements and the test procedures for a pH meter used for continuous on-board monitoring using combination electrodes. The pH meter applies to measuring the pH of the following water for on-board consumption and research purposes: a) natural seawater and freshwater, b) freshwater produced from freshwater generators, c) the used process water for running machinery on-board ships. This document also specifies the method for evaluating performance, calibration, and maintenance of a pH meter used for continuous on-board monitoring.

Ships and marine technology — Marine environment protection — Continuous on-board pH monitoring method

BS ISO 11711-2:2022 船舶和海洋技术 水生公害物种 压载水样品采集和处理

Ships and marine technology. Aquatic nuisance species - Ballast water sample collection and handling

KS V ISO 15370-2022 客船低位照明 布置

Low-location lighting on passenger ships－Arrangement

KS V ISO 20858-2022 海港设施安全评估和安全计划制定

Maritime port facility security assessments and security plan development

KS V 0425-2022 燃油系统

Fuel oil system

ISO 11711-2:2022 船舶和海上技术.水生滋扰物种.第2部分:压载水样品的收集和处理

This document provides requirements and recommendations to ballas t water sampling teams or other concerned parties on the selection and use of sampling apparatus to collect and process ballast water discharge samples aboard a ship from sample ports installed in accordance with ISO 11711-1. It includes an overview of the sampling process, and a discussion on the design and maintenance of sample probes, the necessary sample flow rates, the sample collection devices that incorporate sample flow control to maintain representative sampling conditions, and the handling of samples for subsequent analyses. This document primarily addresses the collection of ballas t water discharge samples . However, it can also be applied to uptake samples with consideration of appropriate sample volumes given anticipated organism concentrations in ambient (as opposed to treated) waters. NO TE While this document is focused on ins tallations aboard a ship, it can be used for land-based facilities .

Ships and marine technology — Aquatic nuisance species — Part 2: Ballast water sample collection and handling

T/CSA 078-2022 船舶舱外可见光通信系统技术要求

本文件规定了基于LED的船舶舱外可见光通信系统的技术要求和试验方法。 本文件适用于基于LED的船舶舱外可见光通信系统，应用场景包括但不限于船舶间通信和船舶与信号塔通信。本文件可用于指导船舶舱外可见光通信系统的搭建，并为相关设备的开发和使用提供技术参考。

Technical requirements for visible light communication systems outside ships

T/CSA 079-2022 船舶内部基于LED照明应用的光通信系统技术要求

本文件规定了船舶内部基于LED照明应用的光通信系统的技术要求和试验方法。 本文件适用于船舶内部环境下，由部分照明用LED发射的可见光（频谱波段380 nm～780 nm）和非照明用LED发射的红外光（频谱波段780 nm～1 mm）作为信息载体的通信技术。本文件可用于指导船舶内部基于照明应用的光通信系统的搭建，并为相关设备的开发和使用提供技术参考。

Technical requirements for optical communication systems based on LED lighting applications in ships

KS A ISO 28001-2022 供应链安全管理体系 实施供应链安全的最佳实践、评估和计划 要求和指南

Security management systems for the supply chain－Best practices for implementing supply chain security, assessments and plans－Requirements and guidance

KS A ISO 28003-2022 供应链安全管理体系 对提供供应链安全管理体系审核和认证的机构的要求

Security management systems for the supply chain－Requirements for bodies providing audit and certification of supply chain security management systems

JT/T 1451-2022 绞吸挖泥船桥架升降系统设计技术要求

本标准适用于绞吸挖泥船桥架升降系统的设计、制造。

Design technical requirements for bridge lifting system of cutter suction dredger

BS EN IEC 63269:2022 海上导航和无线电通信设备和系统 海上幸存者定位装置（人员落水装置）最低要求、测试方法和所需的测试结果

This document specifies the minimum requirements for aspects related to operation, construction, documentation, methods of testing and required test results for ITU-R M.2135 defined by IMO and in accordance with ITU-R M.493 Class-M. This document consists of three modules where the first module, Module A, covers general requirements and aspects. Further Module B covers AIS technologies and Module C covers DSC technologies that are required within MOB equipment. This document incorporates the technical characteristics included in applicable ITU recommendations. Where applicable, it also takes into account the ITU Radio Regulations. This document takes into account other associated IEC International Standards and existing national standards, as applicable. This document defines the requirements for coexistence of AIS and DSC technology incorporated within a single equipment. Only when the equipment complies with the three Modules can it be categorised as AMRD Group A equipment and be entitled to operate on channel AIS 1, channel AIS 2 and channel 70.

Maritime navigation and radiocommunication equipment and systems. Maritime survivor locating devices (man overboard devices). Minimum requirements, methods of testing and required test results

ISO 21070:2017/Amd 1:2022 船舶和海上技术.海洋环境保护.船上垃圾的管理和处理.修改件1:垃圾分类的更新

Ships and marine technology — Marine environment protection — Management and handling of shipboard garbage — Amendment 1: Updates to classification of garbage

ASTM F765-93(2022) 船锚链野猫的标准规范

1.1 This specification covers wildcats as used in windlasses to haul in and pay out anchor chain on board ships. An associated chain stopper is used to secure the chain while the ship is anchored, or the anchor is housed. 1.2 Wildcats are of the five whelp type for use with stud link anchor chain conforming to the American Bureau of Shipping Grades 1, 2, and 3. Wildcat dimensions are provided for chains in integral 1⁄8-in. (3-mm) steps, ranging in size from 3⁄4 to 41⁄8 in. (19 to 104 mm). Wildcat dimensions for chains in intermediate 1⁄16-in. (1.5-mm) steps are not provided, but wildcats in these sizes are permitted within the scope of this specification. 1.3 Wildcats are configured to pass detachable links oriented parallel or perpendicular to the wildcat shaft centerline. 1.4 The values stated in inch-pound units are to be regarded as the standard. This specification is for use with anchor chain that is measured in inch-pound units. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Wildcats, Ship Anchor Chain

EN ISO 24656:2022 海上风电结构的阴极保护

This document specifies the requirements for the external and internal cathodic protection for offshore wind farm structures. It is applicable for structures and appurtenances in contact with seawater or seabed environments. This document addresses: — design and implementation of cathodic protection systems for new steel structures; — assessment of residual life of existing cathodic protection systems; — design and implementation of retrofit cathodic protection systems for improvement of the protection level or for life extension of the protection; — inspection and performance monitoring of cathodic protection systems installed on existing structures, and — guidance on cathodic protection of reinforced concrete structures.

Cathodic protection of offshore wind structures (ISO 24656:2022)

KS V 3990-2022 住舱驾驶室的窗户清洗喷嘴

Window washing nozzles for wheelhouse in accommodation