共找到 1885 条与 航空航天制造用材料 相关的标准,共 126 页
MIL-C-440C, dated 17 November 1998, has been reviewed and determined to be valid for use in acquisition
COMPOSITIONS A-3 AND A-4
MIL-B-5687D, dated 21 February 1984, is hereby reinstated as inactive for new design.
BEARINGS, SLEEVE, WASHERS, THRUST, SINTERED, METAL POWDER, OIL-IMPREGNATED, GENERAL SPECIFICATION FOR
MIL-C-45010A, dated 17 November 1998, has been reviewed and determined to be valid for use in acquisition
COMPOSITION C-4
This drawing documents two product assurance class levels consisting of high reliability (device classes Q andM) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.
MICROCIRCUIT, DIGITAL, RADIATION HARDENED, CMOS, NOR GATE, MONOLITHIC SILICON
The contents of this handbook are limited to general, technical, and operational information. Specific operating procedures and equipment requirements are contained in the Aircraft Refueling NATOPS Manual, NAVAIR 00-80T-109. Accounting and stock control procedures are not included in this handbook or in the NATOPS manual. This handbook is for guidance only and cannot be cited as a requirement.
AIRCRAFT REFUELING HANDBOOK FOR NAVY/MARINE CORPS AIRCRAFT
This specification covers the general requirements for solid state aircraft flashers which are used for cycling aircraft position lights on and off. Flashers will have the load current controlled by a transistor, controlled rectifier, magnetic amplifier or equivalent device. Flashers have either single or dual output circuits.
FLASHER, SOLID STATE, AIRCRAFT NAVIGATIONAL LIGHT, GENERAL SPECIFICATION FOR
This drawing describes the requirements for a family of metal card-retainers intended to hold circuit card ssemblies or printed wiring assemblies in their installed positions.
HOLDER, ELECTRICAL CARD, WEDGE RETAINER, 5-PIECE, .225 INCH BY .225 INCH AND .225 INCH BY .260 INCH BODY SIZE
This drawing describes the requirements for a family of metal 5 wedge electrical card holders (hereafter referred to as card retainers) intended to hold circuit card assemblies or printed wiring assemblies in their installed positions.
HOLDER, ELECTRICAL CARD, WEDGE RETAINER, 5-PIECE, .250 INCH BY .260 INCH BODY SIZE
A-A-59211, dated 18 May 1998, has been reviewed and determined to be valid for use in acquisition
PARTS CLEANING CAN, SAFETY, BENCH [Superseded: NAVY RR-P-125 B CANC NOTICE 1, NAVY RR-P-125 B VALID NOTICE 1, NAVY RR-P-125 B, NAVY RR-P-125 A]
A-A-59119, dated 3 December 1997, has been reviewed and determined to be valid for use in acquisition
LAPPING MACHINES, METAL WORKING, HIGH-PRECISION, FLAT SURFACE
This specification covers requirements, examinations and tests for an explosive designated as Explosive Composition A-5.
EXPLOSIVE COMPOSITION A-5 [Use In Lieu Of: ARMY MIL-E-0014970 C CANC NOTICE 1]
A-A-51161B, dated 11 May 1998, has been reviewed and determined to be valid for use in acquisition
HOLDERS, ELECTRODE, SHIELDED METAL, ARC WELDING
A-A-55536, dated 27 November 1998, has been reviewed and determined to be valid for use in acquisition
PIPES AND ELBOWS, AIR CONDITIONING-HEATING [Superseded: DLA MIL-P-551 E CANC NOTICE 1, DLA MIL-P-551 E (2), DLA MIL-P-551 E (1), DLA MIL-P-551 E, DLA MIL-P-551 D, DLA MIL-P-551 C (3), DLA MIL-P-551 C (2), DLA MIL-P-551 C (1), DLA MIL-P-551 C, D
This drawing describes the requirements for a family of metal extractors intended to aid in removing circuit card assemblies or printed wiring assemblies from their installed positions.
EXTRACTOR, ELECTRICAL CARD, METAL
The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.
HASP, HIGH SECURITY, SHROUDED, FOR HIGH AND MEDIUM SECURITY PADLOCK [Superseded: DLA MIL-H-43905 C CANC NOTICE 2, DLA MIL-H-43905 C NOTICE 1, DLA MIL-H-43905 C, DLA MIL-H-43905 B, DLA MIL-H-43905 A, DLA MIL-H-43905]
This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.
MICROCIRCUIT, DIGITAL, RADIATION HARDENED, ADVANCED CMOS, SYNCHRONOUS 4-BIT UP/DOWN BINARY COUNTER, MONOLITHIC SILICON
The margins of this amendment are marked with an asterisk to indicate where changes from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inc\accuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the margin notations and relationship to the last previous amendment.
MICROPHONE, AND MICROPHONE ASSEMBLIES, DYNAMIC GENERAL SPECIFICATION FOR
SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS
SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS
This supplement forms a part of MIL-PRF-32107.
HOSE, AIR DUCT, GENERAL SPECIFICATION FOR
This specification covers textile duct, manufactured of porous fabric, used as air distribution devices in heating, ventilating, and air conditioning systems for Naval surface ship use.
HOSE, AIR DUCT, GENERAL SPECIFICATION FOR
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号