49.025.20 铝 标准查询与下载

SAE AMS4049L-2010 铝合金,片材和板材,铝衣合金,5.6Zn-2.5Mg-1.6Cu-0.23Cr (铝衣合金7075;-T6片材 -T651板材),溶解和沉淀热处理

This specification covers an aluminum alloy in the form of sheet and plate, clad on two sides. These products have been used typically for structural use, including machined parts subject to excessive warpage during machining. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking; SAE ARP 823 recommends practices to minimize such conditions.

Aluminum Alloy, Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet - T651 Plate) Solution and Precipitation Heat Treated (UNS A97075)

SAE AMS4045K-2010 铝合金薄板及中厚板5.6Zn 2.5Mg 1.6Cu 0.23Cr 7075:(T6片,T651板)解决方案和降水热治疗

This specification covers an aluminum alloy in the form of sheet and plate. These products have been used typically for structural components, including machined parts subject to excessive warpage during maching, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking; ARP823 recommends practices to minimize such conditions.

Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated (UNS A97075)

SAE AMS4044M-2010 铝合金薄板及中厚板5.6Zn2.5Mg1.6Cu0.23Cr煅烧(7075-0)或指定时,由于制造(7075-F)

This specification covers an aluminum alloy in the form of sheet and plate supplied in the annealed (0) condition.When specified, product may be supplied in the "as fabricated" (F) temper. These products have been used typically for formed structural parts which will be subsequently heat treated, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after heat treatment; ARP823 recommends practices to minimize such conditions.

Aluminum Alloy, Sheet and Plate 5.6Zn 2.5Mg 1.6Cu 0.23Cr Annealed (7075-0) or when specified, As Fabricated (7075-F)

SAE AMS4209C-2010 铝合金板材,Alclad6.0Cu0.40Zr(2004-F)的轧制

This specification covers an aluminum alloy in the form of sheet. this product has been used typically for parts requiring a high degree of formability (superplasticity) and response to heat treatment, but usage is not limited to such applications.

Aluminum Alloy Sheet, Alclad 6.0Cu - 0.40Zr - (2004-F) As Rolled (UNS A82004)

SAE AMS7912C-2010 铝铍合金,型材38Al62Be煅烧

This specification covers an aluminum-beryllium alloy in the form of bars, rods, tubing, and shapes consolidated from powder by extrusion. These extrusions have been used typically for parts requiring high thermal conductivity, low density, and high modulus of elasticity, but usage is not limited to such applications.

Aluminum-Beryllium Alloy, Extrusions 38Al 62Be Annealed

SAE AMS7911C-2010 经过热等静压压和热处理的预成型38Al62Be铝铍

This specification covers aluminum and beryllium powders consolidated by hot isostatic pressing (HIP) into the form of bar, rod, tubing, and shapes. These performs have been used typically for parts requiring high thermal conductivity, low density, and high modulus of elasticity, but usage is not limited to such applications.

Aluminum Beryllium, Preforms Hot Isostatic Pressed and Heat Treated 38Al 62Be

SAE AMS4096C-2010 退火的阿尔克莱德包铝(Alclad)铝合金薄板和板材6.3Cu-0.30Mn-0.18Zr-0.10V-0.06Ti(阿尔克莱德包铝(Alclad)2219-0)

This specification covers an aluminum alloy in the form of sheet and plate. This specification has been used typically for parts requiring high strength up to 600 °F (315 °F). These products are also well suited for cryogenic applications and where welding and maximum corrosion resistance are required, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after heat treatment; ARP 823 recommends practices to minimize such conditions.

Aluminum Alloy Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (Alclad 2219-O) Annealed (UNS A92219)

SAE AMS4290L-2010 模铸铝合金压铸件9.5Si-0.50Mg,(360.0-F)

This specification covers an aluminum alloy in the form of die castings. These castings have been used typically for components requiring moderate strength at room temperature, but usage is not limited to such applications.

Aluminum Alloy, Die Castings 9.5Si - 0.50Mg (360.0-F) As Cast

SAE AMS4291H-2010 铝合金压模铸件8.5Si-3.5Cu (A380.0-F)铸态

This specification covers an aluminum alloy in the form of die castings. These castings have been used typically for components of intricate shape, but not having thin sections, but usage is not limited to such applications. This alloy has good casting characteristics by cold-chamber die casting and fair resistance to corrosion.

Aluminum Alloy, Die Castings 8.5Si - 3.5Cu (A380.0-F) As Cast (UNS A13800)

SAE AMS4208C-2010 轧制铝合金薄板材6.0Cu-0.40Zr,(2004-F)

This specification covers an aluminum alloy in the form of sheet. This produce has been used typically for parts requiring a high degree of formability (superplasticity) and response to heat treatment, but usage is not limited to such applications.

Aluminum Alloy Sheet 6.0Cu - 0.40Zr - (2004-F) As Rolled (UNS A92004)

SAE AMS4458-2010 (2.7 Cu 1.8 Li 0.7 Zn)2099-T86固溶处理、冷处理和人工老化的铝合金板

This specification covers an aluminum alloy in the form of plate. This plate has been used typically for parts requiring strength similar to that of 7050-T7451, good resistance to stress corrosion cracking, and having 7.1% lower nominal density, but usage is not limited to such applications.

Aluminum Alloy, Plate (2.7 Cu - 1.8 Li - 0.7 Zn) 2099-T86 Solution Heat Treated, Cold Worked and Artificially Aged

SAE AMS4100E-2010 溶解和沉积热处理5.7Zn 2.2Mg 1.6Cu 0.22Cr(铝衣合金 7475-T761)铝合金,铝衣合金片材

This specification covers an aluminum alloy in the form of alclad sheet. This sheet has been used typically for structural applications requiring material with high strength and resistance to exfoliation-corrosion, moderate fatigue strength, and high fracture toughness, but usage is not limited to such applications.

Aluminum Alloy, Alclad, Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (Alclad 7475-T761) Solution and Precipitation Heat Treated (UNS A87475)

SAE AMS4219F-2010 7.0Si 0.55Mg, 0.12Ti 0.06Be (A357.0 T6)溶解和沉淀热处理的铝合金铸件

This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings. These castings have been used typically for parts, such as hydraulic pump or structural components, requiring high strength, but usage is not limited to such applications.

Aluminum Alloy Castings 7.0Si 0.55Mg, 0.12Ti 0.06Be (A357.0 T6) Solution and Precipitation Heat Treated

SAE AMS4313D-2010 6.3Cu 0.30Mn 0.18Zr 0.10V 0.06Ti (2219-T351, 2219-T352)溶解热处理和机械应力释放的铝合金轧制或锻造环材

This specification covers an aluminum alloy in the form of rolled or forged rings. These rings have been used typically for structural applications requiring good fusion weldability, a combination of good strength and resistance to stress-corrosion cracking, and for parts requiring good stability during machining, but usage is not limited to such applications. Certain design and fabrication procedures may cause these products to become susceptible to stress-corrosion cracking; ARP 823 recommends practices to minimize such conditions. Rings covered by this specification are classified by type of mechanical stress relief as follows: Type 1 - Stress relieved by stretching (2219T351); Type 2 - Stress relieved by compression (2219T352). Either type may be supplied, unless a specific type is ordered.

Aluminum Alloy, Rolled or Forged Rings 6.3Cu 0.30Mn 0.18Zr 0.10V 0.06Ti (2219-T351, 2219-T352) Solution Heat Treated and Mechanically Stress Relieved

SAE AMS4218J-2010 7.0Si 0.35Mg(A356.0-T6P)(原T6P回火)溶解和沉淀热处理的铝合金铸件

This specification covers an aluminum alloy in the form of sand, permanent mold, composite mold, and investment castings. These castings have been used typically for components requiring low weight, moderate strength, and soundness, but usage is not limited to such applications.

Aluminum Alloy Castings 7.0Si 0.35Mg (A356.0-T6P) (Formerly T6P Temper) Solution and Precipitation Heat Treated

KS W ISO 8076-2009 铝及铝合金飞机的阳极氧化膜

Aerospace process－Anodic treatment of aluminium alloys－Chromic acid process 40 V DC, undyed coating

SAE AMS4182G-2009 退火5.0Mg 0.12Mn 0.12Cr (5056-0)铝合金线材

This specification covers an aluminum alloy in the form of wire. This wire has been used typically for the manufacture of screen for reinforcement of, and to provide electrical conductivity through, rubber gaskets, but usage is not limited to such applications.

Aluminum Alloy, Wire 5.0Mg 0.12Mn 0.12Cr (5056-0) Annealed

SAE AMS4261F-2009 沉积热处理7.0Si 0.30Mg, (356.0-T51),铝合金铸件

This specification covers an aluminum alloy in the form of investment castings. These castings have been used typically for small, intricate parts cast to approximately final dimensions, but usage is not limited to such applications.

Aluminum Alloy, Castings, Investment 7.0Si 0.30Mg, (356.0-T51), Precipitation Heat Treated

SAE AMS4080N-2009 退火1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-0)铝合金拉制无缝管道系统

This specification covers an aluminum alloy in the form of drawn seamless tubing. This tubing has been used typically for parts, such as conduits and low-pressure fluid lines, where moderate strength, ductility, and good weldability are required, but usage is not limited to such applications.

Aluminum Alloy, Drawn Seamless Tubing 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-0) Annealed

SAE AMS4241D-2009 枝晶叉间隔(DAS)控制的溶液和沉淀热处理的7.0Si 0.58Mg 0.15Ti 0.06Be(D357.0-T6)铝合金铸件

This specification covers an aluminum alloy in the form of sand castings. These castings have been used typically for structural aircraft components requiring DAS quality control, but usage is not limited to such applications.

Aluminum Alloy Castings 7.0Si 0.58Mg 0.15Ti 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated Dendrite Arm Spacing (DAS) Controlled