49.025.20 铝 标准查询与下载

SAE AMS4161H-2013 溶解热处理和自然老化铝合金挤压制品1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T4)

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing.

Aluminum Alloy, Extrusions 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged

DIN EN 2089:2013 航空航天系列. AL-P2014A-T6或T62铝合金. 薄板材和带材. 0.4 ≤ a ≤ 6 mm; 德文和英文版本EN 2089-2005

Aerospace series - Aluminium alloy AL-P2014A-T6 or T62 - Sheet and strip - 0,4 mm a 6 mm; German and English version EN 2089:2005

SAE AMS4469-2013 溶解热处理,并通过拉伸和老化应力消除无缝拉伸1.8 Cu 1.0 Mg 0.8 Si 0.20 Cr铝合金管件(2013-T4511)

This specification covers an aluminum alloy in the form of seamless, drawn tubing.

Aluminum Alloy Tubing, Seamless, Drawn 1.8 Cu 1.0 Mg 0.8 Si 0.20 Cr Solution Heat Treated, Stress Relieved by Stretching, and Aged (2013-T4511)

SAE AMS4236C-2013 溶解热处理和天然老化4.6Cu 0.35Mn 0.25Mg 0.22Ti (A206.0-T4)铝合金铸件

This specification covers an aluminum alloy in the form of sand, investment, permanent mold, and composite mold castings. Primarily for components requiring high strength combined with good ductility and impact strength. Certain design and processing procedures may cause these castings to become susceptible to stress-corrosion cracking.

Aluminum Alloy Castings 4.6Cu 0.35Mn 0.25Mg 0.22Ti (A206.0-T4) Solution Heat Treated and Naturally Aged

SAE AMS2771E-2013 铝合金铸件的热处理

The specification covers the engineering requirements for heat treatment of aluminum alloy castings and for parts machined from castings.

Heat Treatment of Aluminum Alloy Castings

SAE AMS4132G-2013 冲模和手工溶解和沉淀热处理铝合金锻件,轧制环和锻坯2.3Cu 1.6Mg 1.1Fe 1.0Ni 0.18Si 0.07Ti (2618-T61)

This specification covers an aluminum alloy in the form of die forgings, hand forgings, rolled rings, and forging stock. These products have been used typically for rotating parts operating in service up to 450 °F (232 °C) and other parts operating up to 600 °F (316 °C) at low stresses, but usage is not limited to such applications.

Aluminum Alloy, Die and Hand Forgings, Rolled Rings, and Forging Stock 2.3Cu 1.6Mg 1.1Fe 1.0Ni 0.18Si 0.07Ti (2618-T61) Solution and Precipitation Heat Treated

SAE AMS4459A-2013 伸长1至3%和老化的溶解热处理,应力消除镁合金挤制加工2.7Cu 1.8Li 0.7Zn 0.3Mn 0.3Mg 0.08Zr (2099-T81)

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles (shapes) produced with cross sectional area of 22.5 square inches (145 cm2) maximum and a circumscribing circle diameter (circle size) of 17.4 inches (44.2 cm) maximum.

Aluminum Alloy, Extrusion 2.7Cu 1.8Li 0.7Zn 0.3Mn 0.3Mg 0.08Zr (2099-T81) Solution Heat Treated, Stress Relived by Stretching 1 to 3% and Aged

SAE AMS7488F-2013 闪焊铝和铝合金环材

This specification covers flash welded rings made of aluminum and aluminum alloys. These products have been used typically for parts such as flangers and rings, but usage is not limited to such applications.

Rings, Flash Welded Aluminum and Aluminum Alloys

SAE AMS4016M-2013 应变硬化四分之一硬度和稳定的镁合金薄板和板材,2.5Mg 0.25Cr (5052-H32)

This specification covers an aluminum alloy in the form of sheet and plate. These products have been used typically for parts requiring moderate strength, good formability, good welding and resistance spot welding characteristics, and good resistance to corrosion, but usage is not limited to such applications.

Aluminum Alloy, Sheet and Plate, 2.5Mg 0.25Cr (5052-H32), Strain Hardened, Quarter-Hard, and Stabilized

SAE AMS4413A-2012 3.5Cu 1.0Li 0.40Mg 0.35Mn 0.45Ag 0.12Zr (2050-T84)溶液热处理、应力释放和人工老化的铝合金厚板材

This specification covers an aluminum-lithium alloy in the form of plate. This plate has been used typically for parts where low density is needed in combination with a high level of mechanical properties and very good resistance to stress-corrosion cracking, but usage is not limited to such applications.

Aluminum Alloy, Plate 3.5 Cu 1.0Li 0.40Mg 0.35Mn 0.45Ag 0.12Zr (2050-T84) Solution Heat Treated, Stress Relieved, and Artificially Aged

SAE AMS4470A-2012 经过热溶解处理、消除应力和过老化的的7.5Zn 1.6Cu 1.5Mg 0.12Zr铝合金板材(7085-T7451)

This specification covers an aluminum alloy in the form of plate. This product may be used in aerospace applications requiring a high level of mechanical properties and fracture toughness, good resistance to stress-corrosion cracking and resistance to exfoliation corrosion, but usage is not limited to such applications.

Aluminum Alloy, Plate (7085-T7451) 7.5Zn 1.6Cu 1.5Mg 0.12Zr Solution Heat Treated, Stress-Relieved, and Overaged

SAE AMS4083L-2012 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T6)溶解和沉淀析出热处理液压无缝拉拔铝合金圆管

This specification covers an aluminum alloy in the form of seamless round tubing. This tubing has been used typically for parts operating under high pressure, such as hydraulic systems and fuel and oil lines, but usage is not limited to such applications.

Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T6) Solution and Precipitation Heat Treated

SAE AMS4232C-2012 溶液热处理、冷加工及沉淀热处理的铝合金挤压型材2.7Cu 2.2Li 0.12Zr (2090-T86)

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles. These extrusions have been used typically for parts in structural applications requiring strength similar to 7050-T6 alloy with good exfoliation resistance and with a lower density of approximately 7.8%, but usage is not limited to such applications.

Aluminum Alloy Extrusion 2.7Cu 2.2Li 0.12Zr (2090-T86) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated

SAE AMS4474-2012 溶液热处理、冷加工和人工老化的铝合金薄板材4.0Cu 1.0Li 0.40Mg 0.35Ag 0.13Zr (2195-T8)

This specification covers an aluminum alloy in the form of sheet and plate.

Aluminum Alloy, sheet 4.0Cu 1.0Li 0.40Mg 0.35Ag 0.13Zr (2195-T8) Solution Heat Treated, Cold Worked, and Artificially Aged

SAE AMS4416A-2012 2.9Cu-1.7Li-0.4Mg-0.4Ag-0.10Zr溶解热处理,使用拉伸和人工老化应力释放的铝合金挤压轮廓(2196-T8511)

This specification covers an aluminum-lithium alloy in the form of extruded profiles. These extrusions have been used typically for machined parts requiring dimensional stability during machining processes, and high strength, but usage is not limited to such applications. Certain processing procedures may cause this product to become susceptible to stress-corrosion cracking; ARP823 recommends practices to minimize such conditions.

Aluminum Alloy, Extruded Profiles (2196-T8511) 2.9Cu 1.7Li 0.4Ag 0.10Zr Solution Heat Treated, Stress Relieved by Stretching and Artificially Aged

SAE AMS4124E-2012 溶解热处理,拉伸和过旧进行应力消除的5.6Zn 2.5Mg 1.6Cu 0.23Cr (7075-T73, T7351)铝合金轧制或冷磨光棒材,杆材和线材

This specification covers an aluminum alloy in the form of rolled or cold finished bars, rods, and wire. These products have been used typically for machined parts subject to excessive warpage during machining due to residual stresses and for parts requiring high strength and resistance to stress-corrosion cracking and whose fabrication does not involve forming or welding, but usage is not limited to such applications.

Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 5.6Zn 2.5Mg 1.6Cu 0.23Cr (7075-T73, T7351), Solution Heat Treated, Stress Relieved by Stretching, and Overaged

SAE AMS-A-22771C-2012 热处理铝合金锻件

This specification has previously been widely used and may be required for production or processing of existing designs in the future. The Aerospace Materials Division, however, does not recommend this specification for future use in new designs. This specification covers the requirements for heat treated aluminum alloy die forgings, hand forgings, and ring forgings, produced under additional mechanical property control to ensure known mechanical properties for parts used in aerospace critical applications. This specification also covers the requirements for forgings furnished in the F or 01 conditions which will ultimately be used in the heat treated condition.

Aluminum Alloy Forgings, Heat Treated

SAE AMS4002-2012 通过拉伸和老化(2013-T6511)的无缝拔制1.8Cu 1.0Mg 0.8Si 0.20Cr 熔解热应力消除铝合金管道系统

This specification covers an aluminum alloy in the form of seamless, drawn tubing.

Aluminum Alloy Tubing, Seamless, Drawn 1.8Cu 1.0Mg 0.8Si 0.20Cr Solution Heat Treated, Stress-Relieved by Stretching, and Aged (2013-T6511)

SAE AMS2368C-2012 锻件和锻坯除外的锻造钛原材料的样品和测试

This specification provides a standard set of procedures for sampling and testing to meet the requirements of material specifications for wrought titanium and titanium alloy products except forgings and forging stock. It is applicable to the extent specified in a material specification.

Sampling and Testing of Wrought Titanium Raw Material Except Forgings and Forging Stock

SAE AMS4482-2012 溶解和沉淀热处理4.6Cu 3.4Ti 1.4B 0.75Ag 0.27Mg (A205.0/TiB2/3p-T7P)铸造铝合金复合材料砂铸件

This specification covers a dilute aluminum/TiB2 metal matix composite in the form of sand castings.

Cast Aluminum Alloy Composite 4.6 Cu - 3.4Ti - 1.4B - 0.75Ag - 0.27Mg (A205.0/TiB2/3p-T7P) Sand Cast, Solution and Precipitation Heat Treated