49.025.20 铝 标准查询与下载

SAE AMS4471-2012 熔模铸造,溶解和沉积热处理4.6Cu 3.4Ti 1.4B 0.75Ag 0.27Mg (A205.0/TiB2/3p-T7P)铸造铝合金复合材料

This specification covers a dilute aluminum/TiB2 metal matrix composite in the form of investment castings.

Cast Aluminum Alloy Composite 4.6Cu 3.4Ti 1.4B 0.75Ag 0.27Mg (A205.0/TiB2/3p-T7P) Investment Cast, Solution and Precipitation Heat Treated

SAE AMS4194D-2012 溶解热处理和冷加工铝衣合金,4.4Cu 1.5Mg 0.60Mn,铝合金片材和板材

This specification covers an aluminum alloy in the form of alclad sheet and plate supplied in the -T361 temper. These products have been used typically for high strength parts requiring higher yield strength than is afforded by naturally aged tempers of this alloy and maximum corrosion resistance and whose fabrication does not involve welding, but usage is not limited to such applications.

Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024 -T361 Sheet/Plate with 1?% Alclad) Solution Heat Treated, 6% Cold Worked and Naturally Aged (UNS A82024)

SAE AMS4040N-2012 退火铝衣合金4.4Cu 1.5Mg 0.60Mn (2024 -O and 1-1/2% 铝衣合金)铝合金片材和板材

This specification covers an aluminum alloy in the form of sheet and plate clad on both sides with a different aluminum alloy. These products have been used typically for formed structural parts which will be subsequently heat treated, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after heat treatment; ARP 823 recommends practices to minimize such conditions.

Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024-O with 1 ?% Alclad); Annealed (UNS A82024)

SAE AMS4041R-2012 溶解热处理,冷加工和自然老化的带铝衣合金的铝合金薄板和板材,4.4Cu 1.5Mg 0.60Mn (2024 -T3薄板/-T351 板材带1-1/2%铝衣合金)

This specification covers an aluminum alloy in the form of alclad sheet and plate supplied in the -T3/-T351 temper. These products have been used typically for high strength parts requiring higher yield strength than is afforded by naturally aged tempers of this alloy and maximum corrosion resistance and whose fabrication does not involve welding, but usage is not limited to such applications.

Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024, -T3 Sheet/-T351 Plate with 1?% Alclad) Solution Heat Treated, Cold Worked and Naturally Aged (UNS A82024)

SAE AMS4122L-2012 5.6Zn 2.5Mg 1.6Cu 0.23Cr(7075-T6,7075-T651)溶液和沉淀热处理轧制或冷精整铝合金棒材,杆材和线材

This specification covers an aluminum alloy in the form of rolled or cold finished bars, rods, and wire, and of flash welded rings. These products have been used typically for parts requiring high strength where limited formability is acceptable. Certain design and processing procedures may cause these products to be susceptible to stress-corrosion cracking; SAE ARP 823 recommends practices to minimize such conditions.

Aluminum Alloy, Bars, Rods, and Wire Rolled or Cold Finished, and Rings, 5.6Zn 2.5Mg 1.6Cu 0.23Cr (7075-T6, 7075-T651) Solution and Precipitation Heat Treated

SAE AMS4101E-2012 溶解热处理拉伸沉淀热处理铝合金板4.4Cu 1.5Mg 0.60Mn (2124-T851)

This specification covers an aluminum alloy in the form of plate. This plate has been used typically for parts requiring a high level of mechanical properties up to 300 °F (149 °C), but usage is not limited to such applications.

Aluminum Alloy, Plate 4.4Cu 1.5Mg 0.60Mn (2124-T851) Solution Heat Treated, Stretched, and Precipitation Heat Treated

SAE AMS4186D-2012 在焊接,或当指定条件下,退火(7075-0)轧制或冷轧制5.6Zn 2.5Mg 1.6Cu 0.23Cr (7075-F)铝合金棒,条和线材

This specification covers an aluminum alloy in the form of bars, rods, and wire in the as fabricated (F) temper. When specified, product shall be supplied in the annealed (O) condition. These products have been typically used for parts requiring forming and as stock for flash welded rings which are to be subsequently solution and precipitation heat treated, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after solution and precipitation heat treatment; ARP 823 recommends practices to minimize such conditions.

Aluminum Alloy Bars, Rods, and Wire, Rolled or Cold Finished, 5.6Zn 2.5Mg 1.6Cu 0.23Cr (7075-F) As Fabricated, or when specified, Annealed (7075-0)

SAE AMS4456-2012 溶解热处理压力应力消除和过旧的铝合金手持锻件8.0Zn 1.0Cu 1.6Mg 0.12Zr (7037-T7452)

This specification covers an aluminum alloy in the form of hand forgings 11 inches (280 mm) and under in nominal thickness, and of forging stock.

Aluminum Alloy, Hand Forgings 8.0Zn 1.0Cu 1.6Mg 0.12Zr (7037-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged

SAE AMS4405A-2012 溶液热处理和自然老化的铝合金包铝的薄板(6156-T4) 1.0Si 0.90Cu 0.60Mn 0.90Mg

This specification covers an aluminum alloy procured in the form of sheet Alclad on both sides. These products have been used typically for formed structural parts requiring good formability in T4 temper and ability to develop improved resistance to fatigue crack growth and high toughness with moderate strength when aged to T62 temper, but usage is not limited to such applications.

Aluminum Alloy, Alclad Sheet (6156-T4) 1.0Si 0.90Cu 0.60Mn 0.90Mg Solution Heat Treated and Naturally Aged

SAE AMS-QQ-A-367D-2012 铝合金锻件

This specification covers aluminum alloy die forgings and hand forgings.

Aluminum Alloy Forgings

SAE AMS4459-2012 铝合金，挤压 2.7Cu 1.8Li 0.7Zn 0.3Mn 0.3Mg 0.08Zr（2099-T81）固溶热处理，通过拉伸 1% 至 3% 和时效消除应力

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles (shapes) produced with cross sectional area of 22.5 square inches (145 cm2) maximum and a circumscribing circle diameter (circle size) of 17.4 inches (44.2 cm) maximum.

Aluminum Alloy, Extrusion 2.7Cu 1.8Li 0.7Zn 0.3Mn 0.3Mg 0.08Zr (2099-T81) Solution Heat Treated, Stress Relived by Stretching 1 to 3% and Aged

SAE AMS4229F-2012 高强度铝合金铸件4.5Cu 0.70Ag 0.30Mn 0.25Mg 0.25Ti (A201.0-T7),热处理和应用解决方案

This specification covers an aluminum alloy in the form of sand, permanent mold, and composite mold castings. These castings have been used typically for components requiring a combination of high strength and moderate ductility at both room and elevated temperatures, but usage is not limited to such applications.

Aluminum Alloy Castings, High Strength 4.5Cu 0.70Ag 0.30Mn 0.25Mg 0.25Ti (A201.0-T7) Solution Heat Treated and Overaged

SAE AMS4163E-2012 固溶处理并通过拉伸和矫正消除应力的6.3Cu-0.30Mn-0.18Zr-0.10V-0.06Ti(2219-T3511)铝合金挤压件

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing. These extrusions have been used typically for structural parts requiring high strength up to 500 °F (260 °C) after proper precipitation heat treatment, but usage is not limited to such applications and which may require welding during fabrication. Certain design and fabricating procedures may cause material in the specified condition to be susceptible to stress-corrosion cracking; SAE ARP 823 recommends practices to minimize such conditions.

Aluminum Alloy, Extrusions 6.3Cu 0.30Mn 0.18Zr 0.10V 0.06Ti (2219-T3511) Solution Heat Treated and Stress-Relieved by Stretching, and Straightened

SAE AMS4248C-2012 通过加压释放应力和沉淀热处理的1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T652)溶液热处理铝合金手工铸件和卷形环材

This specification covers an aluminum alloy in the form of hand forgings and rolled rings. These products have been used typically for complex shaped parts requiring moderate strength and good forgeability of the alloy and where stability is required during machining, but usage is not limited to such applications. Corrosion resistance of this alloy is superior to that of aluminum alloys having copper as the principal alloying element.

Aluminum Alloy, Hand Forgings and Rolled Rings 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T652) Solution Heat Treated, Stress Relief by Compression, and Precipitation Heat Treated

SAE AMS4463-2012 固溶热处理的,消除应力的和过老化的含8.0Zn 2.3Cu 2.0Mg 0.12Zr的铝合金板材(7255-T7751)

This specification covers an aluminum ally in the form of plate. This product has typically been used for parts requiring a high level of mechanical properties and moderate exfoliation corrosion resistance, but usage is not limited to such applications.

Aluminum Alloy, Plate (7255-T7751) 8.0Zn 2.3Cu 2.0Mg 0.12Zr Solution Heat Treated, Stress Relieved and Overaged

SAE AMS4134F-2012 4.4Cu 0.85Si 0.80Mn 0.50Mg 2014-T4型溶液热处理的铝合金冲摸锻件

This specification covers an aluminum alloy in the form of die forgings and forging stock. These forgings have been used typically for parts, such as pipe fittings, requiring strength similar to that of parts machined from AMS 4118 bars, but usage is not limited to such applications. Higher strength can be obtained by precipitation hardening to the T6 temper.

Aluminum Alloy, Die Forgings 4.4Cu 0.85Si 0.80Mn 0.50Mg, (2014-T4) Solution Heat Treated

SAE AMS4461-2012 退火的含4.4Cu 1.5Mg 0.60Mn(镀铝的2024-0薄板和板材)的镀铝铝合金薄板和板材.或加工制品(2024-F)(若有规定)

this specification covers an aluminum alloy in the form of sheet and plate supplied in the annealed (O) condition. When specified, product shall be supplied in the "as fabricated" (F) temper.

Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu 1.5Mg 0.60Mn (Alclad 2024-O, Sheet and Plate) Annealed; or when specified, As Fabricated (2024-F)

SAE AMS4029L-2012 溶液沉淀热处理的铝合金薄板材和厚板材(2014;T6型薄板材和T651型厚板材)

This specification covers an aluminum alloy in the form of sheet and plate. These products are used typically for structural parts of good strength, but usage is not limited to such applications. Certain design and processing procedures may cause these products to be susceptible to stress-corrosion cracking; ARP823 recommends practices to minimize such conditions.

Aluminum Alloy, Sheet and Plate (2014; -T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated

SAE AMS4207C-2012 溶液和沉淀热处理的铝合金包铝片材5.7Zn 2.2Mg 1.6Cu 0.22Cr (7454-T61)

This specification covers an aluminum alloy in the form of sheet. This sheet has been used typically for structural applications requiring a combination of high strength, moderate fatigue strength, and high fracture toughness, but usage is not limited to such applications.

Aluminum Alloy Sheet, Alclad, 5.7Zn 2.2Mg 1.6Cu 0.22Cr (7454-T61) Solution and Precipitation Heat Treated

SAE AMS4317A-2012 溶液热处理和老化的铝合金挤制棒材、杆材和型材5.6Zn 2.5Mg 1.6Cu 0.23Cr 7075-T76(51X)

This specification covers an aluminum alloy in the form of extruded bars, rods, and shapes. This product has been used typically for structural applications requiring material with high strength and resistance to exfoliation-corrosion, but usage is not limited to such applications.

Aluminum Alloy, Extruded Bar, Rod, and Shapes 5.6Zn 2.5Mg 1.6Cu 0.23Cr 7075-T76(51X) Solution Heat Treated and Overaged