49.025.99 其他材料 标准查询与下载

SAE AMS5839B-2009 镍合金焊条59Ni 22Cr 2.0Mo 14W 0.35Al的耐腐蚀和耐热性

This specification covers a corrosion and heat resistant nickel alloy in the form of welding wire. This wire has been used typically as filler metal for gas- metal-arc or gas-tungsten-arc welding of parts fabricated from alloy of similar composition, but usage is not limited to such applications.

Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 59Ni 22Cr 2.0Mo 14W 0.35Al

SAE AMS4845H-2009 锡青铜铸件87.5Cu 10Sn 2Zn铸态,沙子和转筒

This specification covers a tin bronze in the form of sand and centrifugal castings. These casting have been typically for bearing requiring a combination of strength, toughness, and resistance to wear, but usage is not limited to such applications. The alloy has good machinability and corrosion resistance to sea water.

Tin Bronze Castings, Sand and Centrifugal, 87.5Cu 10Sn 2Zn, As Cast

SAE AMS7879E-2009 碳化钨.钴粉的铸造和粉粹

This specification covers tungsten carbide-cobalt in the form of powder. This powder has been used typically for producing plasma spray coatings to provide wear and fretting resistant surfaces, but usage is not limited to such applications.

Tungsten Carbide-Cobalt Powder, Cast and Crushed

SAE AMS5894C-2009 固溶热处理的60Co-28Cr-4.5W-1.15C钴合金棒材,片材及板材

This specification covers a cobalt alloy in the form of sheet and plate up to 1 inch (25 mm) in nominal thickness or round bars up to 3 1/2 inches (89 mm) in nominal diameter. These products have been used typically for parts requiring wear resistance and minimum galling or seizing tendencies at room and elevated temperatures, but usage is not limited to such applications.

Cobalt Alloy, Bars, Sheet, and Plate 60Co 28Cr 4.5W 1.15C Solution Heat Treated

SAE AS5127/1B-2009 航空航天密封剂的双组分合成橡胶化合物用航空航天标准测试方法

This SAE Aerospace Standard (AS) describes test methods to determine the application and performance properties of two-component sealing compounds. It shall be used in conjunction with AS5127 and the applicable AMS material specifications.

Aerospace Standard Test Methods for Aerospace Sealants Two-Component Synthetic Rubber Compounds

SAE AMS7875D-2009 碳化铬+镍铬合金粉末75Cr2C3 + 25(80Ni-20Cr合金)

This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder. This product has been used typically for producing plasma spray coatings to provide wear and fretting resistant surfaces, but usage is not limited to such applications.

Powder, Chromium Carbide Plus Nickel-Chromium Alloy, 75Cr₂C₃ + 25(80Ni-20Cr Alloy)

SAE AMS3025C-2009 聚乙二醇热处理淬火介质

This specification covers two types of polyalkylene glycol in the form of a liquid. This product has been used typically as a quenching medium for solution heat treatment of aluminum alloys to minimize distortion and reduce residual stresses.

Polyalkalene Glycol Heat Treat Quenchant

SAE AMS5759L-2009 52Co-20Cr-10Ni-15W固溶热处理耐腐蚀耐热钴合金条,锻件和环

This specification covers a corrosion and heat resistant cobalt alloy in the form of bars, forgings, flash welded rings, and stock for forging, flash welded rings or heading. These products have been tyically used for parts and requiring high strength up to 1500 °F (816 °C) and oxidation resistance up to 2000 °F (1093 °C), but usage is not limited to such applications.

Cobalt Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 52Co 20Cr 10Ni 15W Solution Heat Treated

SAE AMS4855G-2009 85Cu-5.0Sn-5.0Pb-5.0Zn铸造的加铅红黄铜,砂和离心铸件

This specification covers a leaded red brass alloy in the form of sand and centrifugal castings. These castings have been used typically for parts, such as fittings in fluid conducting lines, where soundness of castings is of prime importance, but usage is not limited to such applications.

Leaded Red Brass, Sand and Centrifugal Castings 85Cu 5.0Sn 5.0Pb 5.0Zn As Cast

SAE AMS4860F-2009 58Cu-39Zn-1.2Fe-1.0Al-0.80Mn铸造的锰青铜,砂和离心铸件

This specification covers a manganese bronze alloy in the form of sand and centrifugal castings. These castings have been used typically for parts requiring strength, toughness, and corrosion resistance, but usage is not limited to such applications.

Manganese Bronze, Sand and Centrifugal Castings 58Cu 39Zn 1.2Fe 1.0Al 0.80Mn As Cast

SAE AMS5887C-2009 54Ni-22Cr-12.5Co-9.0Mo-1.2Al耗材电极或真空感应熔化淬火的耐腐蚀耐高温镍合金条,锻件和环

This specification covers a corrosion and heat resistant nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings. These products have been used typically for parts requiring high strength and resistance to oxidation and corrosion up to 2200 °F (1204 °C) and where such parts may require welding during fabrication, but usage is not limited to such applications.

Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 54Ni 22Cr 12.5Co 9.0Mo 1.2Al Consumable Electrode or Vacuum Induction Melted Annealed

SAE AMS5890E-2009 耐腐蚀耐热镍金属条,锻件和钍弥散强化2.2ThO2消除应力的挤压件

This specification covers thoria-dispersion-strengthened nickel in the form of bars, forgings, extrusions, and stock for forging or extruding. These products have been used typically for parts required to operate in the range 1800 to 2400 °F (982 to 1316 °C), but usage is not limited to such applications. A protective coating is required for operation at such temperatures. Fusion welding of structural members is not recommended but the product can be brazed and resistance welded satisfactorily. Products covered by this specification are radioactive. Applicable rules and regulations pertaining to handling of radioactive material should be observed.

Nickel, Corrosion and Heat Resistant, Bars, Forgings, and Extrusions Thoria Dispersion Strengthened 2.2Th0₂ Stress-Relieved

SAE AMS4533C-2009 溶液和沉淀热处理的98Cu-1.9Be铜铍合金条,棒(TF00,原AT)

This specification covers a copper-beryllium alloy in the form of bars and rods. These products have been used typically for parts requiring a combination of high strength, wear resistance, and corrosion resistance and where thermal conductivity, electrical conductivity and low magnetic susceptibility are important, but usage is not limited to such applications.

Copper-Beryllium Alloy, Bars and Rods 98Cu 1.9Be Solution and Precipitation Heat Treated (TF00, formerly AT)

SAE AMS4590C-2009 78.5Cu-10.5Al-5.1Ni-4.8Fe溶液热处理和淬火(TQ50)镍铝铜马氏体挤压件

This specification covers one type of nickel-aluminum bronze in the form of extruded bars, rods, and tubes. These extrusions have been used typically for parts requiring a combination of high strength and hardness with some ductility and toughness, but usage is not limited to such applications.

Extrusions, Nickel-Aluminum Bronze, Martensitic 78.5Cu 10.5Al 5.1Ni 4.8Fe Solution Heat Treated and Tempered (TQ50)

SAE AMS3753B-2009 空心碳微球体

This specification covers carbon in the form of hollow microspheres. This product has been used typically as a filler material in syntactic foam shapes, but usage is not limited to such applications.

Microspheres, Carbon, Hollow

DIN 65672:2009 航空航天.连续丝纤维增强的非电抗热塑层压板.试验板的制备.德文文本和英文文本

This standard specifies the preparation of laminate test panels from textile fabrics, UD products and non-reactive thermoplastics. From the panels test specimen are taken in accordance with the test standard, the specimens being intended for the determination of the characteristics of continuous filament fibre reinforced thermoplastics and for verifying the laminate and sandwich properties.

Aerospace - Continuous filament fibre reinforced laminates with non-reactive thermoplastics - Preparation of test panels; Text in German and English

SAE AMS5888C-2009 退火的含54Ni-22Cr-12.5Co-9.0Mo-1.2Al 耐腐蚀耐热镍合金板

This specification covers a corrosion and heat resistant nickel alloy in the form of plate. This plate has been used typically for parts requiring a combination of high strength and resistance to oxidation and corrosion up to 2200 °F (1204 °C) and where such parts may require welding during fabrication, but usage is not limited to such applications.

Nickel Alloy, Corrosion and Heat Resistant, Plate 54Ni 22Cr 12.5Co 9.0Mo 1.2Al Annealed

SAE AMS5791C-2009 含56.5Co-25.5Cr-10.5Ni-7.5W的等离子喷涂钴合金粉

This specification covers a cobalt alloy in the form of powder. This product has been used typically for producing plasma spray coatings to provide surfaces resistant to wear, corrosion, and abrasion, but usage is not limited to such applications.

Cobalt Alloy, Powder, Plasma Spray 56.5Co 25.5Cr 10.5Ni 7.5W

SAE AMS5871E-2009 固溶热处理的含21Cr-32.5Ni-0.38Ti-0.38Al-45Fe耐腐蚀和耐热的合金薄板材、带材和厚板材

This specification covers a corrosion and heat resistant iron-nickel-chromium alloy in the form of sheet, strip, and plate. These products have been used typically for low-stressed parts requiring corrosion and oxidation resistance particularly where such parts may require welding during fabrication, but usage is not limited to such applications.

Alloy, Corrosion and Heat Resistant, Sheet, Strip and Plate 21Cr 32.5Ni 0.38Ti 0.38Al 45Fe Solution Heat Treated

SAE AMS2759/9D-2009 钢部件的(烘烤法)氢脆性消除

This specification covers the requirements for embrittlement relief (baking) of heat treated steel parts to remove hydrogen infused during plating and other chemical processing (e.g., stripping, chemical milling, pickling, and etching). This specification is applicable to parts made from carbon, low-alloy, and martensitic stainless steel heat treated to a minimum strength of 180 ksi (1241 MPa) or higher heat treated to a minimum hardness of 40 HRC or equivalent, or harder. It is also applicable to threaded fasteners made from carbon, low-alloy, or martensitic stainless steels heat treated to a minimum strength of 150 ksi (1034 MPa) or 34 HRC or equivalent, parts made from high strength precipitation hardening stainless steels other than A-286, and steel parts which have been case hardened (carburized, nitrided, nitrocarburized, or carbonitrided).

Hydrogen Embrittlement Relief (Baking) of Steel Parts