49.030.50 垫圈和其他锁紧元件 标准查询与下载
共找到 486 条与 垫圈和其他锁紧元件 相关的标准，共 33 页
Padded suspension grip clamp with lightening hole (8087)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
本标准规定了带减轻孔双媒栓侧面固定夹紧卡短的结构、尺寸要求。 本标准适用于导管.电费的安装与固定。
Double bolt side fixed grip clamp with lightening hole (8086)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Double bolt side fixed grip clamp with lightening hole (8085)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Double bolt side fixed grip clamp with lightening hole (8084)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Double bolt side fixed grip clamp with lightening hole (8083)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
本标准规定了带减轻孔单蝶栓侧面固定夹紧卡短的结构、尺寸要求。 本标准适用于导管电缆的安装与固定。
Single bolt side fixed grip clamp with lightening hole (8082)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Single bolt side fixed grip clamp with lightening hole (8081)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Single bolt side fixed grip clamp with lightening hole (8080)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Single bolt side fixed grip clamp with lightening hole (8079)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Padded grip clamp with lightening hole (8078)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Padded grip clamp with lightening hole (8077)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Padded grip clamp with lightening hole (8076)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
Padded grip clamp with lightening hole (8075)
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-02-24
- 实施
- 2003-02-24
This standard prescribes test methods, defect definitions, acceptance criteria, and illustrations for assessing the solderability of electronic component leads, terminations,solid wire, stranded wire, lugs, and tabs. This standard is intended for use by b
Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2003-02-01
- 实施
This standard specifies the characteristics, qualification and acceptance requirements for spring tension clips forThe support of electrical harnesses, in alloy steel for aerospace applications.It is applicable whenever referenced.
Aerospace series - Clips, spring tension - Technical specification
- ICS
- 49.030.50
- CCS
- 发布
- 2003-02-01
- 实施
This standard specifies the characteristics of spring tension clips forThe support of electrical harnesses, in FE-PA3903 for aerospace applications.Maximum operating temperature:250 ℃
Aerospace series - Clips, spring tension, in alloy steel FE-PA3903
- ICS
- 49.030.50
- CCS
- 发布
- 2003-02-01
- 实施
(R) LOCK, ROD END, IMPROVED STRENGTH, NAS LUG FSC 5340TABLE 1 - LOCK DIMENSIONSTABLE 2 - WASHER DASH NUMBERS
(R) LOCK, ROD END, IMPROVED STRENGTH, NAS LUG FSC 5340
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2003-01-01
- 实施
This International Standard specifies the characteristics of chamfered washers with counterbore — in alloy steel and cadmium plated, classification 900 MPa/235 ℃; or — in corrosion-resistant steel and passivated, classification 900 MPa/450 ℃. This International Standard is applicable to washers used with ISO 9219 bolts, diameter code 080 to 250, ISO 9216 nuts and ISO 1234 split pins in the assembly of ISO 7939 pulleys. It is also applicable to washers used in the assembly of airframe rolling bearings or spherical bearings. note: 1) Minimum tensile strength of the material at ambient temperature. 2) Maximum temperature, determined by the surface treatment, that the bolt can withstand Without continuous change in its original characteristics after return to ambient temperature.
Aerospace - Washers, chamfered, with counterbore, for pulleys, in alloy steel and cadmium plated or in corrosion-resistant steel and passivated - Dimensions and masses
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2002-12
- 实施
This International Standard specifies the characteristics of flat washers — in alloy steel and cadmium plated, classification 900 MPa/235 ℃; or — in corrosion-resistant steel and passivated, classification 900 MPa/450 ℃. This International Standard is applicable to washers used with ISO 9219 bolts, diameter codes 050 and 060, ISO 9216 nuts and ISO 1234 split pins in the assembly of ISO 7939 pulleys. It is also applicable to washers used in the assembly of airframe rolling bearings or spherical bearings. note: 1) Minimum tensile strength of the material at ambient temperature. 2) Maximum temperature, determined by the surface treatment, that the bolt can withstand without continuous change in its original characteristics after return to ambient temperature.
Aerospace - Washers, flat, for pulleys, in alloy steel and cadmium plated or in corrosion-resistant steel and passivated - Dimensions and masses
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2002-12
- 实施
