共找到 486 条与 垫圈和其他锁紧元件 相关的标准,共 33 页
이 규격은 풀림 방지 철사의 지름에 대해 규정한 것이다. 이 규격은 항공 우주 생산품 표준
Aerospace-Lockwire-Diameters
Aerospace series - Washers in heat resisting steel
Aerospace series - Washers, bulkhead, in titanium alloy
The document specifies the characteristics of washer, bulkhead in titanium alloy intended for use in aircraft fluid system pipe lines.#,,#
Aerospace series - Washers, bulkhead, in titanium alloy; German version EN 3267:2001
(R) Washer, Key - 270 Deg. Locking, CRES, UNS S32100Figure1 washerTable1 dimensions
(R) Washer, Key - 270 Deg. Locking, CRES, UNS S32100
Standards Proposal No. 3801-A-1, Proposed New TP-96 “Plated Through Hole Integrity Test Procedure for Electrical Connectors” (if approved, to be published as ANSVEIA- 364-96, TP-96).
Plated Through Hole Integrity Test Procedure for Electrical Connectors Comment Period Expires: April 6, 2002; ANSI/EIA-364-96,TP-96
This procedure applies to electrical connectors and sockets with values in the range of 10 nanohenrys to 100 nanohenrys.
TP-69A Inductance Measurement Test Procedure for Electrical Connectors and Sockets (10 nH - 100 nH)
This standard defines the terms, abbreviations, and definitions used in the sales and installation of vehicle aftermarket audio and security equipment. The standard adds continuity to mobile electronics installation information, enables easier data collection, and ensures consistency of information to installers.
Mobile Electronics Wiring Designations for Audio, and Vehicle Security/Convenience
This procedure establishes two methods to determine the magnitude of normal force, at the point of the electrical connection, generated by a contact system at a given deflection within its normal operating levels. This data and its relationship to contact
TP-04A Normal Force Test Procedure for Electrical Connectors
This standard specifies the characteristics for washers, bulkhead, in titanium alloy, for aerospace applications.
Aerospace series - Washers, bulkhead in titanium alloy
This standard enumerates and specifies the main characteristics of incandescent lamps for aerospace applications. It shall be used together with EN 2240-001 and the associated product standards.
Aerospace Series Washers, Lock, with Radial Serrations in Corrosion Resisting Steel, Cadmium Plated for Flight Control Rods Dimensions Edition P 1
This standard defines characteristics for spoken audio content and players to improve the listening experience when used together. This standard is not limited to any particular format for publishing content. Instead, this standard works in conjunction with one or more companion standards that define how these characteristics are implemented in a given format. The first of those companion standards, CEA-2003 addresses audiobook compatibility for the CD-MP3 format.
Audiobook Media and Player Compatibility
This test method applies to compliant pins inserted in printed circuit boards with plated-throughholes (PTH).
TP-96 Plated Through Hole Integrity Test Procedure for Electrical Connectors
This test procedure describes two methods to measure the shielding transfer impedance of mated cable connectors in the frequency range 10kHz to 100MHz, (method A), and a connector located between a bulkhead panel and a shielded cable from 30 MHz to 500 MH
TP-80 Low Frequency Shielding Effectiveness Test Procedure for Electrical Connectors and Sockets [Superseded: ECA SP2426, ECA SP2426-A]
This standard is applicable to modular two-part connectors for printed wiring boards associated with equipment for telecommunication or electronic devices using similar techniques. The standard covers high-density connectors providing modular contact arra
Detail Specification for 2 Millimeter, Two-Part Connectors for Use with Printed Boards and Backplanes [Superseded: ECA SP4644-A]
This standard establishes test methods to determine the ability of mated electrical connectors to resist the effects of ice build-up due to water splashing or brief immersion in water, where water is free to drain off of the connector surfaces.
TP-51A ICE RESISTANCE TEST PROCEDURE FOR ELECTRICAL CONNECTORS
Aerospace series - Washers, flat, large diameter, in steel, cadmium plated
This standard specifies the characteristics for washers, bulkhead, in titanium alloy, for aerospace applications.
Aerospace series - Washers, bulkhead in titanium alloy
This standard specifies the characteristics of washers, in heat resisting steel, for aerospace applications.
Aerospace series - Washers in heat resisting steel
This standard specifies the characteristics of washers, in heat resisting steel, for aerospace applications.
Aerospace series - Washers in heat resisting steel
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号