共找到 486 条与 垫圈和其他锁紧元件 相关的标准,共 33 页
This standard establishes test methods for the measurement of the EMI shielding effectiveness of electrical connectors over the frequency range of 1.0 GHz to 10.0 GHz using the mode-stirred technique. The procedure applies to both circular and rectangular
TP-66A EMI Shielding Effectiveness Test Procedure for Electrical Connectors
This standard applies to rectangular cable to board connectors having the following characteristics
Detail Specification for Shielded Rectangular Connectors for Universal Serial Bus Plus Power Connectors Series"B"
This standard establishes test methods to determine the magnitude of porosity as well as other surface defects inherent in application of gold contact finishes.
TP-53B Nitric Acid Vapor Test, Gold Finish Test Procedure for Electrical Connectors and Sockets
This standard applies to rectangular cable to board connectors having the following characteristics: shielded; 8 position; rectangular-shaped mating interface; 2.5 mm pitch spacing on a double row connector; for discrete wire to board appl
Detail Specification for Shielded Rectangular Connectors for Universal Serial Bus Plus Power Connectors Series"A"
This standard specifies the characteristics of flat washers, large diameter, in steel, cadmium plated, for maximum operating temperature 235 °C.
Washers, flat, large diameter, in steel, cadmium plated
This standard specifies the characteristics of flat steel washers, cadmium plated, for maximum operating temperature 235 ℃, for aerospace applications. They are intended for use primarily underneath nuts, for use underneath bolt heads the compatibility shall be checked.
Washers, flat, in steel, cadmium plated
This standard specifies the characteristics of flat steel washers, cadmium plated, for maximum operating temperature 235 °C, for aerospace applications. They are intended for use primarily underneath nuts, for use underneath bolt heads the compatibility shall be checked.
Aerospace series - Washers, flat, in steel, cadmium plated
This standard specifies the characteristics of flat washers, large diameter, in steel, cadmium plated, for maximum operating temperature 235°C.
Aerospace series - Washers, flat, large diameter, in steel, cadmium plated
The document specifies the characteristics of flat steel washers, cadmium plated, for maximum operating temperature 235 ? for aerospace applications. They are intended for use primarily underneath nuts, for use underneath bolt heads the compatibility shall be checked.#,,#
Aerospace series - Washers, flat, in steel, cadmium plated; German version EN 2138:1999
The document specifies the characteristics of flat washers, large diameter, in steel, cadmium plated, for maximum operating temperature 235 ?
Aerospace series - Washers, flat, large diameter, in steel, cadmium plated; German version EN 2913:1999
This Standard applies to a family of connectors having the following characteristics
Detail Specification for Trapezoidal Connectors with Nonremovable Ribbon Cable Contacts on 1.27mm Pitch Double Row Used with Single Connector Attachments (SCA2)
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subjec
TP-38B Cable Pull-Out Test Procedure for Electrical Connectors
This sectional specification is applicable to connectors of use in direct current and analog applications for frequencies below 3 MHz and in digital applications requiring higher data rate frequencies.
Sectional Specification for Rectangular/Trapezoidal Connectors of Certified Quality
This standard specifies the characteristics of flat temperature 235 0C, for aerospace applications.steel washers, cadmium plated, for maximum operatin.
Aerospace series - Washers, flat, in steel, cadmium plated
This portion of the conformance standard specifies tests to determine conformance of a Node's Application Layer to EIA-600. Part One of this standard provides an overview of the conformance philosophy. The reader is urged to review that material before attempting to use the details provided in this part.
Node Application Layer Conformance Specification
This detail specification was fonnuiated for the purpose of providing a document setting forth engineering requirements, quality requirements and application guidelines as necessary for optimum use of rectangular and trapezoidal c~nnectors, of certified q
Blank Detail Specification for Rectangular/Trapezoidal Connectors of Certified Quality
This International Standard specifies the diameters of lockwire. This International Standard is applicable to the compilation of aerospace product standards.
Lockwire. Diameters
Application of this insert bond evaluation procedure is limited to qualification or periodic inspection testing and generally is a test group of its own. This standard provides a technique for evaluating the strength of a bond between one or more componen
TP-79 Insert Bond Strength Test Procedure for Electrical Connectors
This standard establishes a test method to ascertain the abiliq of fully wir-3 connector assemblies to resist the effects of dry dust (fuie sand) laden atmosphere.
TP-50A Dust (Fine Sand) Test Procedure for Electrical Connectors
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号