49.030.50 垫圈和其他锁紧元件 标准查询与下载
共找到 486 条与 垫圈和其他锁紧元件 相关的标准，共 33 页
This standard specifies the characteristics of heat resisting steel, countersunk, load spreading washers for use in aerospace applications at temperatures not exceeding 650 °C. They are intended primarily for use under the head of bolts with strength classification up to 1 250 MPa. They are used to provide sufficient bearing area to prevent indentation of parent metals with low compressive strength at operating temperatures, thus ensuring no relaxation in the bolt load occurs.
Aerospace series - Washers countersunk, load spreading - Heat resisting steel
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2008-05-01
- 实施
This standard specifies the characteristics of threaded, self-locking rings, in FE-PA2601, silver plated, metric, chiefly used for axial location of bearing outer rings. Maximum test temperature of the parts: 450 °C. NOTE These parts are designed to be used with 4H6H internal threads.
Aerospace series - Rings, threaded, self-locking, in heat resisting steel FE-PA92HT (A286), silver plated
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2008-04-30
- 实施
- 2008-04-30
This standard specifies the characteristics of threaded, self-locking rings, in FE-PA2601, silver plated, metric, chiefly used for axial location of bearing outer rings. Maximum test temperature of the parts:450 ℃. NOTEThese parts are designed to be used with 4H6H internal threads.
Aerospace series - Rings, threaded, self-locking, in heat resisting steel FE-PA92HT (A286), silver plated
- ICS
- 49.030.50
- CCS
- 发布
- 2008-04-01
- 实施
This standard specifies the characteristics of threaded, self-locking rings, in FE-PA2601, silver plated, metric, chiefly used for axial location of bearing outer rings. Maximum test temperature of the parts: 450 °C. NOTE These parts are designed to be used with 4H6H internal threads.
Aerospace series - Rings, threaded, self-locking, in heat resisting steel FE-PA92HT (A286), silver plated
- ICS
- 49.030.50
- CCS
- 发布
- 2008-04
- 实施
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subjec
Cable Pull-Out Test Procedure for Electrical Connectors To be published as ANSI/EIA/ECA-364-38C
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2007-07-18
- 实施
his standard establishes the test procedures and test sequences for evaluating compliant contact terminations. The test sequences defined herein shall be considered generic. Unless otherwise specified in the referencing document, this standard applies to
Test Methology for Assessing the Performance of Compliant Contact Terminations Used as Free Standing Contacts or in Electrical Connections and Sockets To be published as ANSI/EIA/ECA-364-1002
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2007-06-12
- 实施
This standard defines the terms, abbreviations, and definitions used in the sales and installation of vehicle aftermarket audio and security equipment. The standard adds continuity to mobile electronics installation information, enables easier data collection, and ensures consistency of information to installers.
Mobile Electronics Wiring Designations for Audio, and Vehicle Security/Convenience
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2007-04-01
- 实施
This standard was developed under the auspices of the Consumer Electronics Association (CEA) Technology & Standards R4.8 DTV Interface Subcommittee. Other scanning structures for analog component interfaces are set forth in separate standards, identified by CEA-770.X notation.
Standard Definition TV Analog Component Video Interface
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2007-04-01
- 实施
Temperature Life With or Without Electrical Load Test Procedure for Electrical Connectors and Sockets To be published as ANSI/EIA/ECA-364-17C
Temperature Life With or Without Electrical Load Test Procedure for Electrical Connectors and Sockets To be published as ANSI/EIA/ECA-364-17C
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2007-02-09
- 实施
Solder Wicking (Wave Solder Technique) Test Procedure for Electrical Connectors and Sockets To be published as ABSI/EIA/ECA-364-71C
Solder Wicking (Wave Solder Technique) Test Procedure for Electrical Connectors and Sockets To be published as ABSI/EIA/ECA-364-71C
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2007-02-05
- 实施
This standard was developed under the auspices of the Consumer Electronics Association (CEA) R6 Mobile Electronics Committee.
Digital Audiobook File Format and Player Requirements
- ICS
- 49.030.50
- CCS
- L23
- 发布
- 2007-02-01
- 实施
The standard specifies the characteristics of tab washers for flight control rods. These tab washers are intended to immobilise the rod end in relation to the rod body, whilst allowing a positional adjustment of 1/2 a turn.#,,#
Aerospace series - Washers, tab in corrosion resisting steel, cadmium plated, for flight control rods - Dimensions; German and English version EN 2328:2006
- ICS
- 49.030.50
- CCS
- V22
- 发布
- 2007-02
- 实施
Aerospace series - Washers, lock, with radial serrations in alloy steel, cadmium plated, for flight control rods - Dimensions; German and English version EN 2327:2006
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2007-02
- 实施
The document defines the dimensions of grooves for axial mounting, external type, retaining rings.
Aerospace series - Groove dimensions for axial mounting external type retaining rings; German and English version EN 3426:2006
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2007-02
- 实施
The document defines the dimensions of grooves for axial mounting, internal type, retaining rings.
Aerospace series - Groove dimensions for axial mounting internal type retaining rings; German and English version EN 3425:2006
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2007-02
- 实施
This standard specifies the characteristics of lock washers in corrosion resisting steel, cadmium plated, with radial serrations primarily intended for flight control rods. These lock washers are intended to immobilise the rod end in relation to the rod body, whilst allowing a precise positional adjustment.#,,#
Aerospace series - Washers, lock, with radial serrations in corrosion resisting steel, cadmium plated for flight control rods - Dimensions; German and English version EN 2596:2006
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2007-01
- 实施
The document defines the dimensions of grooves for radial mounting retaining rings.
Aerospace series - Groove dimensions for radial mounting retaining rings; German and English version EN 3427:2006
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2007-01
- 实施
This specification specifies the characteristics, qualification and acceptance requirements for tension-/sheartype 100?countersunk normal head or protruding head close tolerance lockbolts in titanium alloy TI-P64001, anodized or with aluminium pigmented coating and collars in titanium TI-P99002 or aluminium alloy 2024, metric series, for use as permanent attachment fasteners in shear applications.
Aerospace series - Lockbolts, 100° countersunk normal head or protruding head, tension-/sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating - Collars in titanium TI-P99002 or aluminium alloy 2024 - Metric
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2007-01
- 实施
This standard specifies the characteristics of sheet metal spring retainers in corosion resisting steel, passivated, for use with self-locking barrel nuts EN 4591.
Aerospace series - Retainers, spring, sheet metal, for self-locking barrel nuts, in corrosion resisting steel, passivated; German and English version EN 4590:2005
- ICS
- 49.030.50
- CCS
- V20
- 发布
- 2007-01
- 实施
Aerospace series - Washers, tab in corrosion resisting steel for flight control rods - Dimensions
- ICS
- 49.030.50
- CCS
- 发布
- 2006-12-16
- 实施
- 2006-12-16
