49.035 航空航天制造用零部件 标准查询与下载
共找到 2326 条与 航空航天制造用零部件 相关的标准，共 156 页
This International Standard specifies the characteristics of fork-ends for rolling bearings, in either low alloy steel or corrosion-resistant steel, for aircraft control wire rope.
Aerospace -- Fork-ends, in steel, threaded, for rolling bearings, for aircraft control wire rope -- Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the characteristics of fork-ends for rolling bearings in corrosion-resistant steel swaged on aircraft control wire rope.
Aerospace -- Fork-ends, in corrosion-resistant steel, swaged on aircraft control wire rope for rolling bearings -- Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the possible combinations and lengths of preformed flexible steel wire ropes for aircraft controls equipped with two end-fittings swaged on each end of the cable and the corresponding designations.
Aerospace -- Aircraft control wire rope assemblies -- Dimensions and end-fitting combinations
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
1.1 This International Standard provides a design for quick-release couplings with involute spline drive, intended primarily for aircraft engine/gearbox accessories which require to be removed whilst the engine/gearbox is in service. 1.2 This International Standard comprises — clauses 3 to 12 : Design notes and recommendations; — figure 1/tables 1a) to 1e) : Accessory flanges up to spigot reference 250; — figure 2/tables 2a) to 2d) : Engine/gearbox pads up to spigot reference 250; — figure 3/tables 3a) to 3e) : Accessory flanges above spigot reference 250; — figure 4/tables 4a) to 4e) : Engine/gearbox pads above spigot reference 250; — figure 5/tables 5a) and 5b) : Coupling clamps; — figure 6/tables 6a) and 6b) : Selected involute splines. 1.3 Items subject to agreement between engine/gearbox manufacturer and accessory manufacturer are listed in an annex.
Aircraft -- Accessory drives and mounting pads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the characteristics of eye-ends in corrosion-resistant steel swaged on aircraft control wire rope.
Aerospace -- Eye-ends, in corrosion-resistant steel, swaged on aircraft control wire rope -- Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the requirements for sealed or shielded ball bearings for use in aircraft control cable pulleys conforming to ISO 7939 within the temperature range from - 55 to + 120 °C.
Aircraft -- Ball bearings for control cable pulleys -- Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the characteristics of locking clips in corrosion-resistant steel for aircraft control wire rope turnbuckles.
Aerospace -- Locking clips, in corrosion-resistant steel, for aircraft control wire rope turnbuckles -- Dimensions
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the characteristics, inspections and test methods as well as the quality assurance requirements for aircraft control wire rope assemblies equipped with swaged end fittings. This International Standard is applicable to control wire rope assemblies as defined in ISO 9762.
Aerospace -- Aircraft control wire rope assemblies -- Technical specification
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This part of ISO 2020 specifies the requirements which shall be satisfied by preformed flexible steel wire ropes for aircraft controls. The wire ropes shall be capable of operation within the temperature range of − 54 °C to +121 °C.
Aerospace -- Preformed flexible steel wire rope for aircraft controls -- Part 1: Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the characteristics of ball-ends in corrosion-resistant steel swaged on aircraft control wire rope.
Aerospace -- Ball-ends, in corrosion-resistant steel, swaged on aircraft control wire rope -- Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This part of ISO 8399 establishes the design criteria for accessory drives and mounting flanges with quick attach/detach provisions primarily intended for use in aircraft gearboxes or engine accessories. NOTE — Some design criteria are subject to agreement between the engine/gearbox manufacturer and the accessory manufacturer (see clause 10).
Aerospace -- Accessory drives and mounting flanges (Metric series) -- Part 1: Design criteria
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the characteristics of eye-ends, in either low alloy steel or corrosion-resistant steel, intended for the turnbarrels of aircraft control wire rope.
Aerospace -- Eye-ends, in steel, threaded, for aircraft control wire rope -- Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
This International Standard specifies the characteristics of double-shank ball-ends in corrosion-resistant steel swaged on aircraft control wire rope.
Aerospace -- Double-shank ball-ends, in corrosion-resistiant steel, swaged on aircraft control wire rope -- Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2016-12-22
- 实施
Aerospace series - Bushes, flanged in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series; German and English version EN 4535-2:2016
- ICS
- 49.035
- CCS
- V22
- 发布
- 2016-12
- 实施
Aerospace series - Bushes, plain in aluminium alloy with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series; German and English version EN 4534-2:2016
- ICS
- 49.035
- CCS
- V22
- 发布
- 2016-12
- 实施
Aerospace－Airframe ball bearings, single-row,rigid, diameter series 8 and 9－Metric series
- ICS
- 49.035
- CCS
- 发布
- 20161129
- 实施
- 20161129
Aerospace－Airframe spherical roller bearings, single-row,self-aligning, diameter series 3 and 4－Metric series
- ICS
- 49.035
- CCS
- 发布
- 20161129
- 实施
- 20161129
Aerospace－Airframe ball bearings, double-row,self-aligning, diameter series 2－Metric series
- ICS
- 49.035
- CCS
- 发布
- 20161129
- 实施
- 20161129
Aerospace－Accessory drives and mounting flanges(Metric series)－Part 2：Dimensions
- ICS
- 49.035
- CCS
- 发布
- 20161129
- 实施
- 20161129
Aerospace－Airframe needle track roller,stud type, single-row, sealed－Metric series
- ICS
- 49.035
- CCS
- 发布
- 20161129
- 实施
- 20161129
