纺织玻璃纤维材料标准-分析测试百科网

KS L ISO 5025-2018 加固产品 - 织物 - 宽度和长度的确定

Reinforcement products — Woven fabrics — Determination of width and length

ICS: 59.100.10
CCS
发布: 2018-12-31
实施

KS L ISO 3375-2018(2023) 纺织玻璃粗纱硬度的测定

Textile glass — Determination of stiffness of rovings

ICS: 59.100.10
CCS
发布: 2018-12-31
实施

KS L ISO 1887-2018 纺织玻璃 - 可燃物质含量的测定

Textile glass — Determination of combustible-matter content

ICS: 59.100.10
CCS
发布: 2018-12-31
实施

T/ZZB 0654-2018 风电增强基材用玻璃纤维织物

本标准规定了风电基材用玻璃纤维织物的术语和定义、产品分类、基本要求、技术要求、应用要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。本标准适用于以玻璃纤维为主要原料，以涤纶丝缝编而形成的玻璃纤维经编织物，该织物主要作为增强材料用于风电叶片的基材，如风电叶片的主梁、壳体和腹板及根部等叶片主要组成部位。

Glass fabric for wind power reinforced materials

ICS: 59.100.10
CCS: C175
发布: 2018-10-26
实施: 2019-02-28

T/ZZB 0540-2018 公路工程用短切玄武岩纤维

本标准规定了公路工程用短切玄武岩纤维的术语和定义、分类、标记和规格尺寸、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺等。本标准适用于公路工程用短切玄武岩纤维（以下简称短切玄武岩纤维）。

Chopped basalt fiber for highway engineering

ICS: 59.100.10
CCS: C178
发布: 2018-09-14
实施: 2019-03-14

ASTM E2098/E2098M-13(2018) 确定玻璃纤维增强网的拉伸断裂强度的标准测试方法用于PB外墙外保温和表面处理系统（EIFS）暴露于氢氧化钠溶液

1.1 This test method covers procedures for determining the breaking force of glass fiber mesh following their conditioning in an alkali solution. The method is applicable to glass fiber mesh used in Class PB Exterior Insulation and Finish Systems (EIFS) with base coats that contain portland cement as an ingredient. 1.2 Breaking force is expressed both as force per unit width of mesh and as a percentage of the breaking force of the mesh that has not been exposed to alkali conditioning. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Tensile Breaking Strength of Glass Fiber Reinforcing Mesh for Use in Class PB Exterior Insulation and Finish Systems (EIFS), after Exposure to a Sodium Hydroxide S

ICS: 59.100.10
CCS
发布: 2018-09-01
实施

ASTM D578/D578M-18 玻璃纤维束标准规范

1.1 This specification covers the requirements for continuous fiber and staple fiber glass strands, including single, plied and multiple wound. It also covers textured glass fiber yarns. This specification is intended to assist ultimate users by designating the general nomenclature for the strand products that age generally manufactured in the glass fiber industry. 1.2 Glass fibers are produced having various compositions. General applications are identified by means of a letter designation. The letter designation represents a family of glasses that have provided acceptable performance to the end-user in the intended application. For example, the composition limits stated for E-Glass in this specification representing the glass fiber family for general and most electrical applications is designated by the letter E. Military specifications, such as, MIL-R-60346, recognize the composition limits described in this specification as meeting the respective requirements for E-Glass strands used in reinforced plastic structure applications. 1.3 Glass fiber strands have a variety of general uses under specific conditions, such as high physical or chemical stress, high moisture, high temperature, or electrical environments. Property requirements under specific conditions are agreed upon between the purchaser and the supplier. Electrical property requirements vary with specific end-use applications. For printed circuit board applications, other requirements may be needed such as the use of Institute for Interconnecting and Packaging Electronic Circuits (IPC) Specification EG 4412 A for finished fabric woven from E-Glass for printed circuit boards, or Specification MIL-P-13949 for printed wiring boards applicable to glass fabric base. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This specification is one of a series to provide a substitute for Military Specifications: MIL-Y-1140 Yarn, Cord, Sleeving, Cloth and Tape-Glass; and MIL-C-9084 Cloth, Glass Finished for Resin Laminates. 1.6 Additional ASTM specifications in this series have been drafted and appear in current editions of the Annual Book of ASTM Standards. These include finished glass fabrics, unfinished glass fabrics, glass tapes, glass sleevings, glass cords, glass sewing threads, and finished laminates made from finished glass fabrics. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Glass Fiber Strands

ICS: 59.100.10
CCS
发布: 2018-07-01
实施

ASTM D2343-17 用于增强塑料的玻璃纤维股线纱线和粗纱的拉伸性能的标准试验方法

1.1 This test method covers the determination of the comparative tensile properties of glass fiber strands, yarns, and rovings in the form of impregnated rod test specimens when tested under defined conditions of pretreatment, temperature, humidity, and tension testing machine speed. This test method is applicable to continuous filament, glass fiber materials that have been coated with a resin compatible sizing. This method is intended for use in quality control and R & D, and is not intended to be used to develop composites design data. NOTE 1—This method is technically equivalent to the short method described in ISO 9163. NOTE 2—Prime consideration should be given to the use of a polymeric binder that produces specimens that yield the highest consistent values for the glass fiber material under test. Tensile properties vary with specimen preparation, resin impregnation system, and speed and environment of testing. Consider these factors where precise comparative results are desired. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics

ICS: 59.100.10
CCS
发布: 2017-12-01
实施

ISO 5025:2017 增强制品.机织物.宽度和长度的测定

This document specifies a method for determining the width and length of a woven-fabric reinforcement in the form of a roll1) .

Reinforcement products - Woven fabrics - Determination of width and length

ICS: 59.100.10
CCS: W50
发布: 2017-11-01
实施

ISO 2797:2017 纺织玻璃纤维.粗纱.基本规范

This document establishes a basis for a specification for textile glass rovings, whether direct rovings or assembled rovings.

Textile glass - Rovings - Basis for a specification

ICS: 59.100.10
CCS: W50
发布: 2017-11-01
实施

ISO 3616:2001/Amd 1:2017 纺织玻璃纤维短切原丝和连续长丝毡平均厚度、负载下厚度和压缩后恢复率的测定修改件1

Textile glass — Chopped-strand and continuous-filament mats — Determination of average thickness, thickness under load and recovery after compression — Amendment 1

ICS: 59.100.10
CCS
发布: 2017-08-14
实施