65.060.35 灌溉和排放设备 标准查询与下载

T/SAAMM 1015-2023 扁平双色滴头技术规范

本文件规定了扁平双色滴头的结构、材料、试验条件、技术要求、试验方法、检验规则、包装、标志、运输和贮存等方面的内容。 本文件适用于扁平双色滴头的制造、检验及使用。

Technical specification for flat two-color emitter

T/SAAMM 1021-2023 水肥智能控制系统

本文件规定了水肥智能控制系统的术语和定义、技术要求、检验方法及标志、包装运输和贮存。 本文件适用于水肥智能控制系统。

Water and fertilizer intelligent control system

T/SAAMM 1016-2023 滴头用压力补偿硅胶片

本文件规定了滴头用压力补偿硅胶片的技术要求、试验方法、检验规则以及包装、标志、贮存和运输等内容。 本文件适用于采用连续挤出硫化法生产的硅橡胶原生片、二次硫化后，经冲裁制成的滴头用压力补偿硅胶片的生产、检验及使用。

Pressure compensated silicon film for emitters

DB41/T 2416-2023 高标准农田智慧灌溉技术规程

High standard farmland intelligent irrigation technical regulations

ASTM F2648/F2648M-23 用于土地排水应用的 50 米至 1500 毫米 [2 英寸至 60 英寸] 环形波纹壁聚乙烯（PE）管道和管件的标准规范

1.1  This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 50 mm to 1500 mm [2 in. to 60 in.]. 1.2  The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads. Note 1:  Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based on diameter limitations within the respective standards. Note 2:  Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer applications. 1.3  This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1 ). 1.4  This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5 . 1.5  Units— The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for 50 mm to 1500 mm [2 in. to 60 in.] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

DB42/T 2019-2023 虾稻共作灌溉与排水技术规范

Shrimp and Rice Co-cropping Irrigation and Drainage Technical Specifications

BS ISO 24649:2022+A1:2023 农业灌溉设备 手动和液压操作的塑料阀门

1   Scope This document specifies the general requirements and test methods for manually operated and hydraulically operated plastics valves intended for use in agricultural irrigation systems. It is applicable to manually operated and hydraulically operated plastics valves (as indicated in Table A.2) of nominal sizes DN 8 (1/4") to DN 200 (8").

Agricultural irrigation equipment. Manually and hydraulically operated plastics valves

ISO/CD 7673-1 农业灌溉 第1部分：核心概念、过程和对象

Agricultural Irrigation — Part 1: Core Concepts, Processes, and Objects

ISO/CD 7673-3 农业灌溉 第3部分：灌溉系统操作

Agricultural Irrigation — Part 3: Irrigation System Operations

ISO 24649:2022/Amd 1:2023 农业灌溉设备.手动和液压操作塑料阀 修改件1

Agricultural irrigation equipment — Manually and hydraulically operated plastics valves — Amendment 1

BS ISO 24120-2:2023 农业灌溉设备 加压灌溉系统实施指南 滴灌

1   Scope This document provides a guideline for the implementation of pressurized drip irrigation systems. It is applicable to both small-scale family agriculture and large-scale commercial agriculture, in open fields or within enclosed growing structures (e.g. greenhouse, net house). This document is intended for the use of agriculture ministries, agronomists, irrigation planners, farmers and other end-users.

Agricultural irrigation equipment. Guideline on the implementation of pressurized irrigation systems - Drip irrigation

BS ISO 16399:2023 农业灌溉设备 灌溉水表

1   Scope This document specifies the requirements and certification procedures for water meters , irrespective of the design technologies used to meter the actual volume of cold water or heated water flowing through a fully charged closed conduit. These water meters incorporate devices, which indicate the integrated volume. It applies to water meters intended for irrigation use (herein after referred to as water meters ), regardless of the water quality used for this purpose. This document also applies to water meters based on electrical or electronic principles and to water meters based on mechanical principles, incorporating electronic devices used to meter the actual volume flow of cold water. It provides metrological requirements for electronic ancillary devices when they are subject to metrological control. NOTE Clean water meters are different from irrigation water meters . This document is based on clean water meters standards but, it is important to develop a specific standard for irrigation water meters indicating their specific requirements.

Agricultural irrigation equipment. Meters for irrigation water

ISO 16399:2023 灌溉用水表

This document specifies the requirements and certification procedures for water meters, irrespective of the design technologies used to meter the actual volume of cold water or heated water flowing through a fully charged closed conduit. These water meters incorporate devices, which indicate the integrated volume. It applies to water meters intended for irrigation use (herein after referred to as water meters), regardless of the water quality used for this purpose. This document also applies to water meters based on electrical or electronic principles and to water meters based on mechanical principles, incorporating electronic devices used to meter the actual volume flow of cold water. It provides metrological requirements for electronic ancillary devices when they are subject to metrological control. NOTE Clean water meters are different from irrigation water meters. This document is based on clean water meters standards but, it is important to develop a specific standard for irrigation water meters indicating their specific requirements.

Agricultural irrigation equipment — Meters for irrigation water

ISO 24120-2:2023 农业灌溉设备.加压灌溉系统实施指南.第2部分：滴灌

Agricultural irrigation equipment — Guideline on the implementation of pressurized irrigation systems — Part 2: Drip irrigation

KS B ISO 12374-2022 农业灌溉电力驱动或控制灌溉机的接线和设备

Agricultural irrigation Wiring and equipment for electrically driven or controlled irrigation machines

T/SHDSGY 173-2022 花卉养殖温、湿度自动化控制系统

本文件规定了花卉养殖温、湿度自动化控制系统的术语和定义、工作原理、系统框架、系统功能、要求、安装和验收。 本文件适用于花卉养殖温、湿度自动化控制系统的实施。

Automatic control system of temperature and humidity in flower breeding

KS B 7952-2022 农业灌溉设备.营养液供应商.一般要求

Agricultural irrigation equipment — Nutrient solution supplier — General requirements

T/SAAMM 1004-2022 抗堵塞地埋滴头 技术规范

本文件规定了抗堵塞地埋滴头技术要求及试验条件、试验方法、检验规则、包装、标志、运输和贮存等内容。

Anti-clogging buried dripper technical specification

BS ISO 24120-1:2022 农业灌溉设备 加压灌溉系统实施指南 灌溉的一般原则

Agricultural irrigation equipment. Guideline on the implementation of pressurized irrigation systems - General principles of irrigation

DB43/T 2420-2022 园圃微灌系统建设技术规范

Technical specification for construction of garden micro-irrigation system