65.100.99 其他杀虫剂和农用化工产品 标准查询与下载

T/HNP 001-2024 农药烟剂产品安全生产技术规范

（一）基础部分（第1～3章） 对标准的使用范围、所涉及规范性引用文件和相关的术语与定义进行规定。 （二）基本要求（第4章） 农药烟剂产品生产的基本要求主要包括： 组织机构和职责。主要对企业安全生产责任制、人员岗位职责、负责人职责等给出要求。 管理制度。要求企业制定安全生产相关的基本制度，并在生产人员中贯彻落实。 风险辨识及管控。要求企业建立安全风险辨识管理制度、风险评估管理制度、风险应对管控制度，以保障确保风险来临时具备足够的应对能力。 生产工艺操作规程。要求农药生产企业制定自身的生产工艺操作规程，以保证生产过程的标准化和规范化。 文件和记录管理。要求企业建立完善的记录管理制度，以保证生产、管理过程中相关证据、记录的完善，对溯源管理和监督检查起到支撑作用。 人员培训。要求企业对农药烟剂生产管理人员、操作人员进行培训，保证其具备足够的知识和能力。 现场管理。要求企业对生产现场做好管理，各项安全措施都应配备齐全，日常管理正常开展。 （三）设施设备（第5章） 规定了农药烟剂生产应基本的基本生产设备、包装设备和检验设备生产设施。 （四）生产作业要求（第6章） 对作业环境、条件和人员防护作出要求，要求企业生产厂间的安全设施设备齐全，警示、提示合规，生产员工防护齐全。 对生产操作作出规定安全注意事项做出要求，按照将常见的11个生产阶段的安全注意事项进行说明。 对应急管理处置进行规范，要求企业制定应急处置预案，出现事故时严格按照预案开展应急工作。 对废弃物的处理进行规范。 （五）证实方法（第7章） 规定了检验农药烟剂产品是否按照本文件要求进行安全生产时应检查的文件、制度、记录、信息等。

Specification for safety technology in production of smoke generator pesticides

T/ZNX 030-2023 农药产品碳足迹评价规范

7 数据获取 农药产品生产企业在进行碳足迹评价数据收集时，要根据实际情况按标准对GHG排放和清除核算、生命周期各阶段的数据收集规则、质量要求、分配原则、取舍准则的要求收集，以提高本文件的可操作性。 7.1数据质量要求  数据质量要求应符合国家相关规定，数据收集类目可参考附录D。农药产品碳足迹评价过程中使用的数据应满足以下要求： 完整性：应涵盖对评价农药产品系统有实质性贡献的所有GHG的排放与清除； 代表性：使用对评价农药产品而言具有时间、地理及技术针对性的数据； 准确性：避免非必要偏差和导致不确定度增加的任何操作； 延续性：数据在时间上具备延续性，使用最近至少一年的数据，不足一年取全部。 优先使用初级数据，若无法获取初级数据，可使用次级数据，并进行书面记录，解释数据来源和使用理由。 7.2数据抽样  1)若某单元过程输入的同一数据来自多个源头，宜选择具有代表性、权威性和保守性的数据样本进行GHG排放与清除数据的核算。抽样数据应满足7.1规定的数据质量要求。 2)若单一原材料来自多个供应商时，宜收集所有供应商的初级数据。若收集所有初级数据存在困难，则宜收集供应原材料数量50%以上的或具有代表性供应商的初级数据，其加权平均值可作为无法取得数据的供应商的次级数据。 3)若产品运输路线不止一条，宜收集所有路线的初级数据。若收集所有初级数据存在困难，则宜收集销售量占总销售量50%以上的或具有代表性的主要销售点的运输路线，其加权平均值可作为无法取得数据的路线的次级数据。 7.3数据收集要求  在确定农药产品碳足迹评价过程中活动水平数据、排放因子所使用的初级活动水平数据还是次级数据时，对不同活动水平和排放因子要求不同，详见附录附录E。 7.4分配原则 若所评价农药产品的生产系统不是单一的产品系统，有共生产品的产出，则其GHG的排放量必须进行分配，分配程序及分配方法遵循如下原则： （1）GHG分配应根据GB/T 24040—2008 及 GB/T 24044—2008 中规定的分配程序。 （2）对包含多个产品或循环体系的系统，宜避免分配。若分配无法避免，考虑以下方面： a.优先使用物理关系进行分配； b.若无法建立物理关系，宜根据经济价值或其它关系进行分配，且应提供所使用分配关系的依据及计算说明。 注：物理关系包括数量、质量、工时等有明显关联关系。 7.5取舍原则 7.5.1 基本要求 不应将对农药产品碳足迹有实质性贡献的GHG排放与清除排除在外。应量化至少95%与功能单位相关的生命周期内预计会产生的GHG排放与清除量，即GHG排放或清除量小于所评价产品GHG总排放或清除量估测值1%的可予以舍去，但累计不应超过5%。 7.5.2 毒害物质 农药产品生产过程中涉及较多的有毒有害物质，取舍准则不适用于这类物质，农药产品碳足迹评价应包含所有有毒有害的材料和物质。 7.5.3 记录保留 在农药产品碳足迹评价过程中舍去的GHG排放与清除应有书面记录。所选择的取舍准则对评价结果产生的影响应在评价报告中做出解释。

Carbon footprint evaluation specifications for pesticide products

T/HEBQIA 146-2023 2-氯-5-氯甲基噻唑

本文件规定了2-氯-5-氯甲基噻唑的要求、试验方法、检验规则、标志、标签、包装、运输和贮存。

2-Chloro-5-chloromethylthiazole

T/CAPDA 030-2022 杀虫单副产工业盐-氯化钠

本文件规定了杀虫单副产工业盐-氯化钠的产品分类、技术要求、试验方法、检验规则、使用和 包装、标识、运输、储存。 本文件适用于杀虫单副产工业盐-氯化钠的质量控制。

Thiosultap-monosodium Byproduct Industrial Salt of Sodium Chloride

T/CCPIA 199-2022 0.01％24-表芸苔素内酯可溶液剂

本文件规定了0.01％24-表芸苔素内酯可溶液剂的技术要求、试验方法、检验规则、验收和质量保证期以及标志、标签、包装、储运。

0.01% 24-epibrassinolide soluble concentrate

T/CCPIA 202-2022 农药中间体 双甘膦

本文件规定了双甘膦的技术要求、试验方法、检验规则、验收以及标志、标签、包装、储运。

N-(phosphonomethyl)iminodiacetic acid

DB14/T 2345-2021 土壤熏蒸防治设施蔬菜土传病虫害技术规程

本标准规定了土壤化学熏蒸防治设施蔬菜土传病虫害的术语和定义、防治药剂、防治技术、熏蒸后管理和档案管理。 本标准适用于为控制设施蔬菜土传病虫害而进行的土壤熏蒸处理。

Technical regulations for soil fumigation control facility vegetable soil borne diseases and insect pests

ASTM E2043-99(2021) 用热重分析法测定农业佐剂溶液中不挥发物质的标准试验方法

1.1 This test method covers the determination of the nonvolatile matter of agricultural tank mix adjuvant solutions by thermogravimetry. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Nonvolatile Matter of Agricultural Adjuvant Solutions by Thermogravimetry

T/CCPIA 097-2021 农药中间体 2-氯-5-氯甲基噻唑

本文件规定了2-氯-5-氯甲基噻唑的要求、试验方法、验收、验收期以及标志、标签、包装、储运。 

Pesticide intermediate 2-chloro-5-chloromethylthiazole

T/CCPIA 098-2021 农药中间体 3-甲基-4-硝基亚胺-1,3,5-噁二嗪

本文件规定了3-甲基-4-硝基亚胺-1,3,5-噁二嗪的要求、试验方法、检验规则、验收期以及标志、标签、包装、储运。

Pesticides intermediate 3-methyl-4-nitroimino-perhydro-1,3,5-oxadiazine

T/CCPIA 096-2021 农药中间体 3-(氨甲基)四氢呋喃

本文件规定了3-(氨甲基)四氢呋喃的要求、试验方法、检验规则、验收期以及标志、标签、包装、储运。

Pesticides intermediate 3-（Aminomethyl）tetrahydrofuran

T/CCPIA 095-2021 农药中间体 N-氰基乙亚胺酸乙酯

本文件规定了N-氰基乙亚胺酸乙酯的要求、试验方法、检验规则、验收期以及标志、标签、包装、储运。 

Pesticides intermediate N-cyanoethanimidic acid ethyl ester

ASTM E2044-99(2019) 液体农业喷雾混合物扩散的标准试验方法

1.1 This test method covers the visual evaluation of the relative spread radius of liquid spray mixture droplets. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Spreading of Liquid Agricultural Spray Mixtures

ASTM E1163-10(2019) 估计大鼠急性口服毒性的标准试验方法

1.1 This test method determines the lethality (LD50 value, slope and 95 % confidence interval (CI)) and signs of acute toxicity from a material using a limited number of rats. The technique used in this test method is referred to as the “Stagewise, Adaptive Dose Method.”2 This test method is an alternative to the classical LD50 test and is applicable to both liquids and solids. 1.2 This test method is not recommended for test materials which typically produce deaths beyond two days postdosing. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Estimating Acute Oral Toxicity in Rats

ASTM E645-18 用于冷却水系统的杀菌剂的评估标准实践

1.1 This practice outlines a procedure for evaluating the efficacy of microbicides (algicides, bactericides, and fungicides) that will be used for controlling microbial growth in cooling water systems. The microbicides will be evaluated using simulated or real cooling tower water against (1) microbes from cooling water, (2) microbes in microbiological deposits (biofilms) from operating cooling systems, or (3) microorganisms known to contaminate cooling water systems, or a combination thereof. This practice should be performed by individuals familiar with microbiological techniques. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Evaluation of Microbicides Used in Cooling Water Systems

DB6169/T 123.1-2018 解淀粉芽孢杆菌生物防治技术规程第1部分：苹果花脸病

Technical Regulations for Biological Control of Bacillus Amyloliquefaciens Part 1: Apple Face Disease

DB6169/T 123.2-2018 解淀粉芽孢杆菌生物防治技术规程第2部分：猕猴桃溃疡病

Technical regulations for biological control of Bacillus amyloliquefaciens Part 2: Kiwi canker

DB32/T 2582-2013 设施蔬菜土壤化学消毒剂使用技术规程

Technical regulations for the use of chemical disinfectants for vegetable soil in facilities

ASTM E645-13 用于冷却水系统的杀菌剂的评估标准实践

5.1 This practice determines potentially effective microbicides for use in cooling water systems using cooling water and deposits/biofilm obtained from the field. The addition of deposits/biofilms addresses the need to include the major source of microorganisms in cooling water systems. Even with this addition, laboratory results may not be totally predictive of microbicidal effectiveness in the field. This is because conditions in the field affecting microbicide effectiveness are difficult to mimic in the laboratory. These conditions that affect microbicide efficacy include blow-down rate, addition of makeup water, water hardness, hydrocarbon leaks, pH, sediment loading, dissolved solids, microbes in slime (biofilms), and deposits (salts, iron minerals, organics, and so forth) on surfaces. An additional factor is the difficulty in enumerating all microbes in the water due to the lack of adequate recovery media. Guidelines that address formation of and testing for surface-attached microbes (biofilms) may be found in Guide E1427, while a guideline for unconventional measurement of microbes is found in Guide E1326. 1.1 This practice outlines a procedure for evaluating the efficacy of microbicides (algicides, bactericides, and fungicides) that will be used for controlling microbial growth in cooling water systems. The microbicides will be evaluated using simulated or real cooling tower water against (1) microbes from cooling water, (2) microbes in microbiological deposits (biofilms) from operating cooling systems, or (3) microorganisms known to contaminate cooling water systems, or a combination thereof. This practice should be performed by individuals familiar with microbiological techniques. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Evaluation of Microbicides Used in Cooling Water Systems

DB52/T 784-2012 茶假眼小绿叶蝉监测与无害化治理技术规程

Technical regulations for monitoring and harmless treatment of tea leafhoppers with false eyes