71.080.20 卤代烃 标准查询与下载

KS M 1664-2013 工业用四氯化碳

Carbon tetrachloride for industrial use

KS M ISO 3427:2013 气态卤代烃（液化气） 取样

Gaseous halogenated hydrocarbons(liquefied gases) ? Taking of a sample

KS M 4825-2013 4-羟基-1-萘磺酸钠 [内维尔和温特斯酸（钠盐）]

SODIUM 4 HYDROXY-1-NAPHTHALENE SULFONATE [NEVILLE AND WINTHERS ACID(SODIUM SALT)]

KS M 4823-2013 有机中间体的通用测试方法

GENERAL TESTING METHODS FOR ORGANIC INTERMEDIATES

KS M ISO 3363:2012 工业用氟氯代烃.酸度的测定.滴定法

이 표준은 산업용 염화플루오린계 탄화수소의 산도 정량에 관한 적정법에 대하여 규정한다.

Fluorochlorinated hydrocarbons for industrial use－Determination of acidity－Titrimetric method

ASTM D5837-12 高效液相色谱（HPLC）电绝缘液中呋喃化合物的标准测试方法

Furanic compounds are generated by the degradation of cellulosic materials used in the solid insulation systems of electrical equipment. Furanic compounds which are oil soluble to an appreciable degree will migrate into the insulating liquid. High concentrations or unusual increases in the concentrations of furanic compounds in oil may indicate cellulose degradation from aging or incipient fault conditions. Testing for furanic compounds may be used to complement dissolved gas in oil analysis as performed in accordance with Test Method D3612. 1.1 This test method covers the determination in electrical insulating liquids of products of the degradation of cellulosic materials such as paper, pressboard, and cotton materials typically found as insulating materials in electrical equipment. These degradation products are substituted furan derivatives, commonly referred to as furanic compounds or furans. This test method allows either liquid/liquid or solid phase extraction (SPE) of the furanic compounds from the sample matrix followed by analysis for specific furanic compounds by HPLC or direct injection for analysis of specific furanic compounds by HPLC. 1.2 The individual furanic compounds that may be identified and quantified include the following: 5-hydroxymethyl-2-furaldehyde furfuryl alcohol 2-furaldehyde 2-acetylfuran 5-methyl-2-furaldehyde 1.3 The direct injection method generally has a higher limit of detection, especially for furfuryl alcohol. Greater interference for furfuryl alcohol may be expected when using the direct injection method as opposed to extraction methods. 1.4 This test method has been used to successfully test for furanic compounds in mineral insulating oil, silicone fluid, high fire point electrical insulating oils of mineral origin, askarels, and perchloroethylene-based dielectric fluids. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Furanic Compounds in Electrical Insulating Liquids by High-Performance Liquid Chromatography (HPLC)

ASTM D2109-01(2011) 卤化有机溶剂及其混合物中不挥发物质的标准试验方法

Standard Test Methods for Nonvolatile Matter in Halogenated Organic
Solvents and Their Admixtures

ASTM D4755-95(2010) 卤化有机溶剂及其混合物中游离卤素的标准试验方法

Standard Test Method for Free Halogens in Halogenated Organic Solvents and Their Admixtures

ASTM D3448-10 三氯三氟代乙烷的特殊水性电导率的标准试验方法

This test method allows for the determination of ionizable contaminants (expressed in terms of ppb of HCl) in trichlorotrifluoroethane via measurement of specific aqueous conductance. This test method can be used for establishing manufacturing and purchasing specifications.1.1 This test method covers the determination of aqueous conductivity due to ionizable contaminants extracted from trichlorotrifluoroethane. The value of 1.9 μS/cm as maximum specific aqueous conductance corresponds to 0.1 ppm of chloride ion (100 ppb). It was calculated by putting the solvent specification of 0.1 ppm chloride into the equation of the subject method to find C2 − C1 equals 19.08. The specific conductance due to contaminants from the solvent was then calculated as follows:

Standard Test Method for Specific Aqueous Conductance of Trichlorotrifluoroethane

ASTM D1901-10 卤化有机溶剂及其添加剂的相对蒸发时间的标准试验方法

This test method gives valid comparisons of the evaporation rates of the subject materials. These comparisons are required for the determination of the suitability of a proposed material for specific cleaning applications.1.1 This test method covers the measurement of the relative evaporation time of halogenated organic solvents and their admixtures. This test method is not applicable in the presence of excessive drafts or high-velocity air currents. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Relative Evaporation Time of Halogenated Organic Solvents and Their Admixtures

ASTM D4995-10 1,1,2-三氯-1,2,2-三氟乙烷溶剂的电子和脱脂等级的标准规范

1.1 This specification establishes the requirements for three grades of trichlorotrifluoroethane solvent: 1.1.1 Type I electronic or ultra-clean grade, 1.1.2 Type II standard or vapor-degreasing grade, and 1.1.3 Type IIA general purpose, packaged in a pressurized container grade. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specifications for Electronic and Degreasing Grades of 1,1,2-Trichloro 1,2,2,-Trifluoroethane Solvent

KS M 1320-2009 1、1、1、2-四氟乙烷(HFC-134a)

이 표준은 산업용 1,1,1,2-테트라플루오로에테인(HFC-134a)에 대하여 규정한다.

1,1,1,2-Tetrafluoroethane(HFC-134a)

KS M 1320-2009(2019) 1,1,1,2-四氟乙烷（HFC-134a）

1,1,1,2-Tetrafluoroethane(HFC-134a)

KS M 1958-2009 工业用四氯化碳试验方法

Carbon tetrachloride for industrial use－Methods of test

KS M 1964-2009 工业用三氯乙烯试验方法

Trichloroethylene for industrial use－Methods of test

KS M 1513-2008(2018) 三氯乙烯

Tricloroethylene for industrial use

KS M 1513-2008(2023) 工业用三氯乙烯

Tricloroethylene for industrial use

KS M 1513-2008 三氯乙烯

이 표준은 산업용 트라이클로로 에틸렌(이하, 트라이클로로 에틸렌이라 한다.)에 대하여 규정

Tricloroethylene for industrial use

KS M 1649-2008 丁醇

이 표준은 산업용 부탄올(이하, 부탄올이라 한다.)에 대하여 규정한다.

Butanol

KS M 4821-2008(2014) 苯胺

Aniline