71.080.90 酚 标准查询与下载

KS I 9245-2019 涂料和染料中氯酚的测定

Determination of chlorophenols in paints and dyes

DB22/T 256-2018 工业对叔丁基苯酚含量的测定 大口径毛细管柱气相色谱法

Determination of industrial p-tert-butylphenol content by gas chromatography with large bore capillary column

DB22/T 262-2018 工业2,6-二叔丁基苯酚含量的测定 大口径毛细管柱气相色谱法

Determination of industrial 2,6-di-tert-butylphenol content by gas chromatography with large bore capillary column

DB22/T 264-2018 工业间对甲酚含量的测定 大口径毛细管柱气相色谱法

Determination of p-cresol content in industry by gas chromatography with large bore capillary column

DB22/T 263-2018 工业2,4-二叔丁基苯酚含量的测定 大口径毛细管柱气相色谱法

Determination of industrial 2,4-di-tert-butylphenol content by gas chromatography with large bore capillary column

HG/T 5274-2017 4-氯-3,5-二甲基苯酚

4-Chloro-3,5-dimethylphenol

YB/T 5082-2016 粗酚 灼烧残渣的测定方法

本标准规定了重量法测定灼烧残渣量。 本标准适用于从煤焦油、含酚污水制取的粗酚灼烧残渣的测定。

Crude phenol.The mothod for determination of residue after ignition

ASTM D2439-16 精制苯酚的标准规范

1.1 This specification covers refined phenol. 1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 Consult current OSHA regulations and supplier’s Safety Data Sheets, and local regulations for all materials listed in this specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Refined Phenol

ASTM D4493-16 双酚A (4.4-双酚A) 凝固点的标准试验方法

5.1 The solidification point of bisphenol A is a direct indication of its purity, although it gives no information as to the nature of any impurities present. 5.2 High purity bisphenol A has a solidification point of approximately 157°C. 5.3 This test method can be used for internal quality control or for setting specifications. 1.1 This test method describes the procedure for determination of the solidification point of bisphenol A (4,4′-isopropylidene diphenol). 1.2 The test method has been found applicable for determination of the solidification point between 150 and 157°C. 1.3 In determining conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.

Standard Test Method for Solidification Point of Bisphenol A(4,4&x2032;-Isopropylidenediphenol)

YB/T 4493-2015 焦化油类产品馏程的测定 自动馏滴法

本标准规定了自动馏滴法测定焦化轻油类馏程的原理、试样的采取、仪器、试验步骤、结果计算、精密度、试验报告等。 本标准适用于焦化轻油类(焦化苯类、酚类、吡啶类、喹啉类等)、粘油类(焦化洗油、蒽油、木材防腐油、炭黑用焦化原料油等)产品馏程的测定。

Coking oil products-determination of distillation rang.Automatism control distil

ASTM D4297-15(2020) 采取样和处理双酚A(4,4&x2032;-异丙基二苯酚)的标准实施规程

3.1 This practice is issued to provide information useful in establishing sampling and handling procedures. It is expected that this information will only be utilized in conjunction with an existing health and safety program and consultation with an appropriate SDS. The information provided herein cannot be used as a substitute for expert safety and medical advice as provided in an appropriate SDS, but rather as a supplement to such advice. 1.1 This practice covers procedures for safely sampling and handling 4,4′-isopropylidinediphenol, commercially known as bisphenol A (BPA), in various solid forms, and as a liquid at elevated temperatures in a manner which represents and preserves product quality. 1.2 Any person sampling or handling this product should have consulted a safety Data Sheet (SDS) for specific first aid instructions and information on the proper equipment to have available for use in the event of personal contact or exposure. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 3, 4, 5, 6, 7 and 8 and an appropriate SDS. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling and Handling Bisphenol A(4,4&x2032; -Isopropylidinediphenol)

ASTM D4297-15 双酚A (4,4&x2032; -二酚基丙烷) 取样和搬运的标准实施规程

3.1 This practice is issued to provide information useful in establishing sampling and handling procedures. It is expected that this information will only be utilized in conjunction with an existing health and safety program and consultation with an appropriate SDS. The information provided herein cannot be used as a substitute for expert safety and medical advice as provided in an appropriate SDS, but rather as a supplement to such advice. 1.1 This practice covers procedures for safely sampling and handling 4,4′-isopropylidinediphenol, commercially known as bisphenol A (BPA), in various solid forms, and as a liquid at elevated temperatures in a manner which represents and preserves product quality. 1.2 Any person sampling or handling this product should have consulted a safety Data Sheet (SDS) for specific first aid instructions and information on the proper equipment to have available for use in the event of personal contact or exposure. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 3, 4, 5, 6, 7 and 8 and an appropriate SDS.

Standard Practice for Sampling and Handling Bisphenol A(4,4&x2032; -Isopropylidinediphenol)

ASTM D4789-12 双酚A（4,4'-异丙基二苯酚）溶液颜色的标准试验方法

1.1 This test method describes the procedure for determination of the Platinum-Cobalt Color of bisphenol A (4,4???-Isopropylidenediphenol) dissolved in methanol. 1.2 This test method has been found applicable for the determination of Platinum-Cobalt color of bisphenol A between 20 and 100 color units. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.

Standard Test Method for Solution Color of Bisphenol A (4,4`-Isopropylidenediphenol)

ASTM D4493-12 双酚A（4,4`-异亚丙基双酚）凝固点的标准试验方法

1.1 This test method describes the procedure for determination of the solidification point of bisphenol A (4,4???-isopropylidene diphenol). 1.2 The test method has been found applicable for determination of the solidification point between 150 and 157??C. 1.3 In determining conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.

Standard Test Method for Solidification Point of Bisphenol A (4,4`-Isopropylidenediphenol)

KS M 1671-2010 五氯苯酚(PCP)(工业用)

이 표준은 방부제, 방충제, 살균제의 목적으로 사용되는 펜타클로로페놀(이하 PCP라 한다.

Pentachlorophenol

ASTM D1631-10(2018)e1 碘试剂法测定苯酚及相关材料中水含量的标准试验方法

5.1 This test method is particularly useful for determining small amounts of water in hygroscopic materials. This test method is suitable for setting specifications on materials referenced in the scope. It may also be used as an internal quality control tool and in development or research work. 1.1 This test method covers the determination of water in phenol and related materials such as cresols, xylenols, naphthalene, pyridine, and quinoline. 1.2 This test method has been found applicable to a variety of materials varying in water content from 100 mg/kg to solutions containing a relatively high percent of water. 1.3 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water in Phenol and Related Materials by the Iodine Reagent Method

ASTM D4297-10 双酚 A(4,4''-二酚基丙烷)的采样和搬运

This practice is issued to provide information useful in establishing sampling and handling procedures. It is expected that this information will only be utilized in conjunction with an existing health and safety program and consultation with an appropriate MSDS. The information provided herein cannot be used as a substitute for expert safety and medical advice as provided in an appropriate MSDS, but rather as a supplement to such advice.1.1 This practice covers procedures for safely sampling and handling 4,4′-isopropylidinediphenol, commercially known as bisphenol A (BPA), in various solid forms, and as a liquid at elevated temperatures in a manner which represents and preserves product quality. 1.2 Any person sampling or handling this product should have consulted a Material Safety Data Sheet (MSDS) for specific first aid instructions and information on the proper equipment to have available for use in the event of personal contact or exposure. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.

Standard Practice for Sampling and Handling Bisphenol A (4,4' -Isopropylidinediphenol)

KS M 9245-2008 油漆和颜料中氯酚分析方法

이 표준은 도료, 염료 등의 공업 제품 중 클로로페놀류의 분석 방법을 위한 전처리 및 추출

Determination of chlorophenols in industrial products as paint, dye

JIS K 2437:2008 酚(苯酚、邻甲酚、甲酚和二甲苯酚)

This Standard specifies the phenol, o-cresol, cresols and xylenols used for the industrial material and the like.

Phenols (phenol, o-cresol, cresols and xylenols)

SNI 06-4582-1998 液体苯酚

Liquid phenol