共找到 146 条与 铝矿 相关的标准,共 10 页
Aluminium ores-Preparation of pre-dried test samples
Determination of available aluminum and active silicon content in bauxite trihydrate by inductively coupled plasma atomic emission spectrometry
Smelter grade alumina. Specifications
This International Standard sets out requirements for the sampling of aluminium ores from moving streams and stationary situations, including stopped-belt sampling, to provide gross samples for sample preparation. Stopped-belt sampling is the reference method for collecting ore samples against which other sampling procedures may be compared. Sampling from moving streams is the preferred method. Sampling from stationary situations should only be considered when sampling from moving streams is not possible. The procedures described in this International Standard for sampling from stationary situations merely minimize some of the sampling errors. Although this International Standard is intended to cover all aluminium ore sampling from moving streams, the procedures recommended may not be applicable in cases of extreme segregation, for example very wet ore due to its sticky nature, or very dry ore due to generation of dust. In such cases it may be necessary to revert to stopped-belt sampling.
Aluminium ores -- Sampling procedures
This International Standard specifies a BPHA spectrophoto-metric method for the determination of the vanadium content of aluminium ores. It is applicable to ores containing between 0,005 % (m/m) and 0,4 % (m/m) of vanadium pentoxide.
Aluminium ores - Determination of vanadium content -- BPHA spectrophotometric method
This International Standard specifies a method for the determination of the moisture content of aluminium ores. It applies to the samples taken from bulk aluminium ores, e.g. shipments and stockpiles. Annex A specifies a method to be used when it is difficult to carry out sieving, crushing and dividing owing to the sample being adhesive or excessively wet. In this case the sample may be pre-dried until preparation can be conducted without any trouble and the pre-dried moisture content of a consignment can be determined by the procedure specified in annex A. Annex B specifies methods of correction for sprayed water and/or rainfall. In the event of the consignment being subjected to rainfall and/or sprayed water to control dust emission, then the moisture content of the consignment can be corrected for this added water in accordance with annex B.
Aluminium ores -- Determination of the moisture content of bulk material
Scope is not provided for this standard
Aluminium ores -- Determination of aluminium content -- EDTA titrimetric method
Scope is not provided for this standard
Aluminium ores -- Experimental determination of the heterogeneity of distribution of a lot
Scope is not provided for this standard
Aluminium ores -- Determination of iron content -- Titrimetric method
Scope is not provided for this standard
Aluminium ores -- Preparation of samples
Scope is not provided for this standard
Aluminium ores -- Experimental methods for checking the bias of sampling
Scope is not provided for this standard
Aluminium ores -- Determination of titanium content -- 4,4'-Diantipyrylmethane spectrophotometric method
Scope is not provided for this standard
Aluminium ores -- Determination of total iron content -- Titanium trichloride reduction method
Scope is not provided for this standard
Aluminium ores -- Experimental methods for checking the precision of sampling
Scope is not provided for this standard
Aluminium ores -- Determination of total silicon content -- Combined gravimetric and spectrophotometric method
1.1 This test method covers the determination of silica in fluorspar in concentrations from 0.5 % to 10 %. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Determination of Silica in Fluorspar by Silico-Molybdate Visible Spectrophotometry
The method ist applicable to all aluminium ores having loss of mass values in the range of 10 to 30 %. Specifies principle, reagents, apparatus, sampling and samples, procedure, expression of results and test report.
Aluminium ores — Determination of loss of mass at 1 075 degrees C — Gravimetric method
이 표준은 알루미늄 광석의 총 규소 분석 방법에 대한 무게 분석법과 흡광 광도법에 대하여
Aluminium ores-Determination of total silicon content-Combined gravimetric and spectrophotometric method
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号