75.080;75.100 标准查询与下载

KS M 2418-2006 石油产品和润滑剂的、碳、氢、氮的仪器分析试验方法

1 이 규격은 석유 제품 및 윤활제의 시험실 시료 중 탄소, 수소 및 질소의 기기 분석 방

Standard test method for instrumental determination of carbon, hydrogen, and nitrogen in petroleum products and lubricants

GOST R 52532-2006 基础油.采用气相色谱法测定N-甲基吡咯烷酮

Base oils. Gas chromatographic method for determination of N-methylpyrrolidone

GOST R 52559-2006 机油.采用冷启动模拟器测定5鳦至35鳦时表观粘度的方法

Engine oils. Method for determination of apparent viscosity at temperatures between -5 °C and -35 °C using the cold-cranking simulator

DS/EN 12766-3:2005 石油产品和用过的油 多氯联苯和相关产品的测定 第3部分：使用电子 ca 的气相色谱法（GC）测定和定量多氯三联苯（PCT）和多氯苄基甲苯（PCBT）的含量

This document specifies a method of test for the determination of polychlorinated terphenyls (PCT) and polychlorinated benzyl toluenes (PCBT) in petroleum products and related materials by means of a specified gas chromatographic separation procedure. Followiing the gas chromatographic separation, quantification procedures are described for PCT Aroclor 5442, PCT Aroclor 5460 and PCBT (Ugilec 141). This document is applicable to unused, used and treated (e.g. dechlorinated) petroleum products including synthetic lubricating oils, to petroleum products and synthetic lubricating oils suitably recovered from other materials (e.g. from waste materials) and to mi

Petroleum products and used oils - Determination of PCBs and related products - Part 3: Determination and quantification of polychlorinated terphenyls (PCT) and polychlorinated benzyl toluenes (PCBT) content by gas chromatography (GC) using an electron ca

NF T60-184-3*NF EN 12766-3:2005 石油产品和用过的油.PCB和相关产品的测定.第3部分:用电子俘获探测器的气相色谱法测定和量化多氯三联苯(PCT)和多氯甲苯((PCBT)含量

Petroleum products and used oils - Determination of PCBs and related products - Part 3 : determination and quantification of polychlorinated terphenyls (PCT) and polychlorinated benzyl toluenes (PCBT) content by gas chromatography (GC) using an electron c

DIN EN 12766-3:2005 石油产品和用过的油.多氯联苯和相关产品的测定.第3部分:用电子俘获探测器的气相色谱法测定多氯三联苯(PCT)和多氯甲苯((PCBT)含量

Petroleum products and used oils - Determination of PCBs and related products - Part 3: Determination and quantification of polychlorinated terphenyls (PCT) and polychlorinated benzyl toluenes (PCBT) content by gas chromatography (GC) using an electron ca

BS EN 12766-3:2004 石油产品和废油 PCB 及相关产品的测定 多氯三联苯的测定和定量

This document specifies a method of test for the determination of polychlorinated terphenyls (PCT) and polychlorinated benzyl toluenes (PCBT) in petroleum products and related materials by means of a specified gas chromatographic separation procedure. Following the gas chromatographic separation, quantification procedures are described for PCT Aroclor 5442, PCT Aroclor 5460 and PCBT (Ugilec 141). This document is applicable to unused, used and treated (e.g. dechlorinated) petroleum products including synthetic lubricating oils, to petroleum products and synthetic lubricating oils suitably recovered from other materials (e.g. from waste materials) and to mixtures of vegetable oils. NOTE 1 This document has been developed as an extension of EN 12766 Parts 1 and 2 to provide a method of determining the total PCB content in accordance with Articles 2, 3 and 4 of EC Directive 96/59/EC [1]. The total PCB content is calculated by summation of PCB content, determined according to EN 12766-2, and PCTs and PCBTs according to this document. The three classes of materials measured in this standard can be quantified if they occur at concentrations greater than given in Table 1. NOTE 2 In order to simplify and rationalize the analytical operations required for an effective, fast and economic inventory of equipment containing liquids classified as PCBs (as defined by Directive 96/59/EC [1]), it is recommended firstly to determine, using an appropriate screening method, the total chlorine content (in mg/kg). Examples for analytical procedures to determine total chlorine content in fresh, used, or treated insulating oils are: i) pre-dosed colorometric kits to measure 25 mg/kg or 50 mg/kg total chlorine (ref: US EPA SW-846 Method 9079); ii) electrochemical methods in the range 2 mg/kg to 2 000 mg/kg of total chlorine (ref: DEXSIL L-2000 DXC - US EPA SW-846 Method 9079 and US EPA SW-846 Method 9078); iii) wavelength dispersive X-ray fluorescence; or iv) oxidative microcoulometry or other scientifically validated analytical methods. From the total chlorine measured for a specific sample, a theoretical maximum equivalent PCB content can be calculated. When this maximum equivalent PCB content is significantly lower than the limit prescribed by Directive 96/59/EC [1] (50 mg/kg total PCBs) or by local standards (e.g. 25 mg/kg total PCBs), the sample may be considered as "PCB-free". NOTE 3 When the total chlorine content in a sample is higher than the limits described above, it becomes necessary to proceed with gas chromatographic analysis in accordance with this document using the total chlorine content as: i) a guide to establish the level of dilution necessary to operate within the linear range of the ECD detector (EN 12766-1:2000, 10.3.2); ii) a method of calculating the ratio between total chlorine content and total PCB for quality control purposes; iii) a method for the classification of the hazard posed by the oil (e.g. at the end of its life cycle, for regeneration, use as fuel and/or disposal in accordance with local regulations). NOTE 4 For the purposes of this document, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction and the volume fraction. WARNING —The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Petroleum products and used oils. Determination of PCBs and related products. Determination and quantification of polychlorinated terphenyls (PCT) and polychlorinated benzyl toluenes (PCBT) content by gas chromatography (GC) using an electron capture d...

DIN EN ISO 2719:2003 闪点的测定.宾-马氏闭口杯闪点测定法

This standard specifies a method for the determination of flash point using Pensky-Martens closed cup method.

Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2002); German version EN ISO 2719:2002

JIS K 2501:2003 石油产品及润滑剂.中和数值的测定

この規格は，石油製品及び潤滑油の中和価を指示薬滴定法，.電位差滴定法及び指示薬光度滴定法によって，測定する方法について規定する。

Petroleum products and lublicants -- Determination of neutralization number

NF T60-184-2*NF EN 12766-2:2002 石油产品和用过的油.多氯联苯及相关产品的测定.第2部分:多氯联苯(PCB)含量计算

Petroleum products and used oils - Determination of PCBs and related products - Part 2 : calculation of polychlorinated biphenyl (PCB) content.

DIN ISO 6614:2002 石油产品.石油和合成流体的脱水性能测定 (ISO 6614:1994)

The document specifies a method for measuring the ability of petroleum oils or synthetic fluids to separate from water.

Petroleum products - Determination of water separability of petroleum oils and synthetic fluids (ISO 6614:1994)

DIN EN 12766-2:2001 石油产品和用过的油.多氯联苯和相关产品测定.第2部分:多氯联苯(PCB)含量计算

This standard specifies a calculation procedure for total PCB content (Method A) and a calculation for the PCB content based on six congeners (Method B). The basis for this quantification is taken from part 1 of this standard, in which all necessary experimental procedures are described for the specific analysis of unused, used and treated (e.g. dechlorinated) petroleum products including synthetic lubricating oils and to petroleum products and synthetic lubricating oils suitably recovered from other materials, e.g. from waste materials.#,,#

Petroleum products and used oils - Determination of PCBs and related products - Part 2: Calculation of polychlorinated biphenyl (PCB) content; German version EN 12766-2:2001

DS/EN 12766-2:2001 石油产品和废油 多氯联苯和相关产品的测定 第2部分：多氯联苯（PCB）含量的计算

This standard specifies two calculation procedures (""method A"" and ""method B"") for PCB content. The basis for this quantification is taken from the chromatographic results of EN 12766-1, in which all necessary experimental procedures are described for the specific analysis of unused, used and treated (e.g. dechlorinated) petroleum products including synthetic lubricating oils and mixtures of vegetable oils.

Petroleum products and used oils - Determination of PCBs and related products - Part 2: Calculation of polychlorinated biphenyl (PCB) content

BS EN 12766-2:2001 石油及其产品的试验方法 石油产品和废油 PCB 及相关产品的测定 多氯联苯（PCB）含量的计算

Identical with IP 462.2:2001.

Methods of test for petroleum and its products. Petroleum products and used oils. Determination of PCBs and related products. Calculation of polychlorinated biphenyl (PCB) content

DIN EN 12766-1:2000 石油产品和用过的油.多氯联苯和相关产品的测定.第1部分:使用电子俘获检测器(ECD)的气相色谱法(GC)分离和测定所选多氯联苯的衍生物

Petroleum products and used oils - Determination of PCBs and related products - Part 1: Separation and determination of selected PCB congeners by gas chromatography (GC) using an electron capture detector (ECD); German version EN 12766-1:2000

BS EN 12766-1:2000 石油及其产品的测试方法 石油产品和废油 PCB 及相关产品的测定 使用电子捕获检测器(ECD)通过气相色谱(GC)分离和测定选定的 PCB 同系物

Identical with IP 462/2001.

Methods of test for petroleum and its products. Petroleum products and used oils. Determination of PCBs and related products. Separation and determination of selected PCB congeners by gas chromatography (GC) using an electron capture detector (ECD)

NP EN 22719-2000 石油产品和润滑油．闪点的测定（Pensky-Martens）彭斯克-马丁闭口杯法（ISO 2719-1988）

A presente Norma destina-se a fixar um processo de, usando o equipamento Pensky-Martens de vaso fechado, determinar o ponto de inflama??o de combustíveis líquidos, líquidos com sólidos em suspens?o, óleos lubrificantes, líquidos que tendem a formar uma película superficial nas condi??es do ensaio e outros líquidos. Os pontos de inflama??o e combust?o em vaso aberto, podem ser determinados pela ISO 2592:1973, os pontos de inflama??o de tintas, vernizes e óleos de secagem podem ser determinados pela ISO 1523:1983. ISO 2592:1973, Petroleum products. Determination of flash and fire points. Cleveland open cup method. ISO 1523:1983, Paints, varnishes, petroleum and related products. Determination of flashpoint. Closed cup equilibrium method NOTA 1: O método descrito nesta Norma pode ser usado para a detec??o da contamina??o de óleos lubrificantes por fracas quantidades de matérias voláteis, o que também muitas vezes ocorre em óleos de transformadores devido a cis?es moleculares parciais. Contudo, a mais baixa temperatura à qual estes produtos s?o capazes de produzir atmosferas inflamáveis pode ser inferior à determinada por este método. (Veja-se também a sec??o 6, segundo parágrafo e a nota de 7.3). NOTA 2: Esta Norma deverá ser usada para medir e definir o comportamento de materiais, produtos ou sistemas em presen?a do calor e chama, sob condi??es laboratoriais controladas. Em condi??es reais de incêndio, a reac??o ao calor e chama poderá ser diferente.

Petroleum products and lubricants Determination of flash point Pensky-Martens closed cup method(ISO 2719-1988)

DS/EN 12766-1:2000 石油产品和废油 多氯联苯和相关产品的测定 第1部分：使用电子捕获检测器（ECD）通过气相色谱（GC）分离和测定选定的多氯联苯同系物

This European Standard specifies a method to determine the concentration of up to 12 individual or defined unresolved small groups of polychlorinated biphenyl (PCB) congeners in petroleum products and related materials by means of a specified gaschromatographic separation procedure. The gas chromatographic separation is valid for the different quantification procedures described in Part 2 of this European Standard.

Petroleum products and used oils - Determination of PCBs and related products - Part 1: Separation and determination of selected PCB congeners by gas chromatography (GC) using an electron capture detector (ECD)

GOST R 51634-2000 自动拖拉机用机油.一般技术要求

Настоящий стандарт распространяется на группу однородной продукции - автотракторные моторные масла и устанавливает показатели качества,

Motor oils for autotractors. General technical requirements

ISO 6618:1999/Cor 1:1999 石油产品和润滑剂.酸和中和碱值的测定.颜色指示剂滴定法.技术勘误1

This standard is Petroleum products and lubricants - Determination of acid or base number - Coulour-indicator titration method; Technical Corrigendum 1

Petroleum products and lubricants - Determination of acid or base number - Coulour-indicator titration method; Technical Corrigendum 1