75.180.10 勘探和钻采设备 标准查询与下载

GSO ISO 19901-5:2023 石油和天然气工业 海上结构物的特殊要求 第5部分：重量管理

This document specifies requirements for managing and controlling the weight and centre of gravity (CoG) of offshore facilities by means of mass management during all lifecycle phases including; conceptual design, front end engineering design (FEED), detail engineering, construction and operations. These can be new facilities (greenfield) or modifications to existing facilities (brownfield). Weight management is necessary throughout operations, decommissioning and removal to facilitate structural integrity management (SIM). The provisions of this document are applicable to fixed and floating facilities of all types. Weight management only includes items with static mass. Snow and ice loads are excluded as they are not considered to be part of the facility. Dynamic loads are addressed in ISO 19904-1, ISO 19901-6 and ISO 19901-7. This document specifies: a) requirements for managing and controlling weights and CoGs of assemblies and entire facilities; b) requirements for managing weight and CoG interfaces; c) standardized terminology for weight and CoG estimating and reporting; d) requirements for determining not-to-exceed (NTE) weights and budget weights; e) requirements for weighing and determination of weight and centre of gravity (CoG) of tagged equipment, assemblies, modules and facilities; This document can be used: f) as a basis for costing, scheduling or determining suitable construction method(s) or location(s) and installation strategy; g) as a basis for planning, evaluating and preparing a weight management plan and reporting system; h) as a contract reference; i) as a means of refining the structural analysis or model.

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 5: Weight management

GSO ISO 19903:2023 石油和天然气工业 混凝土海上结构

This document specifies requirements and provides recommendations applicable to fixed, floating and grounded concrete offshore structures for the petroleum and natural gas industries and for structures supporting nationally-important power generation, transmission or distribution facility. This document specifically addresses — the design, construction, transportation and installation of new structures, including requirements for in-service inspection and possible removal of structures, — the assessment of structures in service, and — the assessment of structures for reuse at other locations. This document is intended to cover the engineering processes needed for the major engineering disciplines to establish a facility for offshore operation.

Petroleum and natural gas industries — Concrete offshore structures

GSO ISO 18797-2:2023 石油、石化和天然气工业 立管的涂层和衬里外部腐蚀防护 第2部分：立管维护和现场修复涂层

This document specifies the selection criteria and minimum requirements for protective coating systems for maintenance and field repair of risers exposed to conditions in the splash zone. It is applicable for maintenance requirements and field repairs of riser coatings. This document does not apply to the selection of techniques and materials used to restore integrity of the risers to be coated, nor does it apply to the selection of additional mechanical protective materials that are not part of the coating systems described in this document. New construction shop applied riser coatings are covered in ISO 18797-1. Compatible maintenance and repair coating systems specified in ISO 18797-1 are covered in this document.

Petroleum, petrochemical and natural gas industries — External corrosion protection of risers by coatings and linings — Part 2: Maintenance and field repair coatings for riser pipes

GSO ISO 13354:2023 石油天然气工业 钻井与生产设备 浅层气分流设备

ISO 13354:2014 specifies requirements for the selection of the diverter equipment for rigs used to drill shallow-gas-bearing formations. It covers both onshore and offshore drilling operations, and considers also the auxiliary equipment associated with floating rigs. The specified requirements concern the following diverter equipment: annular sealing devices; vent outlets; diverter valves; diverter piping. ISO 13554:2014 highlights the concerns associated with the selection of a marine floating drilling support. It covers safety issues concerning key rig equipment, and important steps of action required prior to starting the drilling operations. It provides only general guidelines regarding the response to be given to a shallow-gas flow.

Petroleum and natural gas industries — Drilling and production equipment — Shallow gas diverter equipment

GSO ISO 13678:2023 石油和天然气工业 用于套管、油管、管线管和钻杆元件的螺纹化合物的评估和测试

ISO 13678:2010 provides requirements, recommendations and methods for the testing of thread compounds intended for use on threaded casing, tubing, and line pipe connections; and for thread compounds intended for use on rotary shouldered connections. The tests outlined are used to evaluate the critical performance properties and physical and chemical characteristics of thread compounds under laboratory conditions. These test methods are primarily intended for thread compounds formulated with a lubricating base grease and are not applicable to some materials used for lubricating and/or sealing thread connections. It is recognized that many areas can have environmental requirements for products of this type. ISO 13678:2010 does not include requirements for environmental compliance. It is the responsibility of the end user to investigate these requirements and to select, use and dispose of the thread compounds and related waste materials accordingly.

Petroleum and natural gas industries — Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements

GSO ISO 19901-2:2023 石油和天然气工业 海上结构物的特殊要求 第2部分：抗震设计程序和标准

This document contains requirements for defining the seismic design procedures and criteria for offshore structures; guidance on the requirements is included in Annex A. The requirements focus on fixed steel offshore structures and fixed concrete offshore structures. The effects of seismic events on floating structures and partially buoyant structures are briefly discussed. The site-specific assessment of jack-ups in elevated condition is only covered in this document to the extent that the requirements are applicable. Only earthquake-induced ground motions are addressed in detail. Other geologically induced hazards such as liquefaction, slope instability, faults, tsunamis, mud volcanoes and shock waves are mentioned and briefly discussed. The requirements are intended to reduce risks to persons, the environment, and assets to the lowest levels that are reasonably practicable. This intent is achieved by using: a) seismic design procedures which are dependent on the exposure level of the offshore structure and the expected intensity of seismic events; b) a two-level seismic design check in which the structure is designed to the ultimate limit state (ULS) for strength and stiffness and then checked to abnormal environmental events or the abnormal limit state (ALS) to ensure that it meets reserve strength and energy dissipation requirements. Procedures and requirements for a site-specific probabilistic seismic hazard analysis (PSHA) are addressed for offshore structures in high seismic areas and/or with high exposure levels. However, a thorough explanation of PSHA procedures is not included. Where a simplified design approach is allowed, worldwide offshore maps, which are included in Annex B, show the intensity of ground shaking corresponding to a return period of 1 000 years. In such cases, these maps can be used with corresponding scale factors to determine appropriate seismic actions for the design of a structure, unless more detailed information is available from local code or site-specific study. NOTE      For design of fixed steel offshore structures, further specific requirements and recommended values of design parameters (e.g. partial action and resistance factors) are included in ISO 19902, while those for fixed concrete offshore structures are contained in ISO 19903. Seismic requirements for floating structures are contained in ISO 19904, for site-specific assessment of jack-ups and other MOUs in the ISO 19905 series, for arctic structures in ISO 19906 and for topsides structures in ISO 19901‑3.

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 2: Seismic design procedures and criteria

ISO 13703-3:2023 石油和天然气工业，包括低碳能源 — 海上生产平台和陆上工厂的管道系统 — 第 3 部分：制造

Oil and gas industries including lower carbon energy — Piping systems on offshore production platforms and onshore plants — Part 3: Fabrication

ISO 10425:2023 石油和天然气工业用钢丝绳 最低要求和验收条件

Steel wire ropes for the petroleum and natural gas industries — Minimum requirements and terms of acceptance

ISO 15551:2023 石油和天然气工业 钻井和生产设备 人工举升电潜泵系统

Petroleum and natural gas industries — Drilling and production equipment — Electric submersible pump systems for artificial lift

ISO/CD 10855-1:2023 近海集装箱和相关起重装置 第 1 部分：近海集装箱的设计、制造和标记

Offshore containers and associated lifting sets — Part 1: Design, manufacture and marking of offshore containers

ISO/CD 10855-3:2023 海上集装箱和相关起重设备 - 第 3 部分：定期检查、检查和测试

Offshore containers and associated lifting sets — Part 3: Periodic inspection, examination and testing

ISO/CD 10855-2:2023 海上集装箱和相关起重装置 第 2 部分：起重装置的设计、制造和标记

Offshore containers and associated lifting sets — Part 2: Design, manufacture and marking of lifting sets

ISO 13703-2:2023 石油和天然气工业，包括低碳能源 — 海上平台和陆上工厂的管道系统 — 第 2 部分：材料

Oil and gas industries including lower carbon energy — Piping systems on offshore platforms and onshore plants — Part 2: Materials

ISO 19901-8:2023 石油和天然气工业 海上结构物的特殊要求 第 8 部分：海洋土壤调查

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 8: Marine soil investigations

ISO 24202:2023 石油和天然气工业，包括低碳能源 — 海上项目的散装材料 — 单轨梁和 padeye

Oil and gas industries including lower carbon energy — Bulk material for offshore projects — Monorail beam and padeye

T/CPSI 01201-2023 半潜式生产平台总体设计规范

Overall design specifications for semi-submersible production platforms

23/30437660 DC BS EN ISO 6398-1 石油和天然气工业 用于人工举升的潜水式直线电机系统 第1部分：潜水式直线电机

BS EN ISO 6398-1. Petroleum and natural gas industries. Submersible linear motor systems for artificial lift - Part 1. Submersible linear motors

T/CPI 11018-2023 石油天然气钻采设备 自动化连续管作业机

本文件规定了石油天然气钻采设备自动化连续管作业机的型式、型号、基本参数、配置要求、技术要求、试验和检验等要求。 本文件适用于石油天然气钻采设备自动化连续管作业机的设计、制造和验收。

Oil and gas drilling equipment automated coiled tubing operating machine

T/CPI 11022-2023 石油天然气用水下井口装置

本文件规定了石油天然气用水下井口装置的产品设计、材料及焊接要求、工厂试验、装置标识、防护及运输等内容。 本文件适用于额定工作压力不超过103.5MPa且额定工作温度不高于177℃的水下井口装置。

Oil and gas underwater wellhead equipment

T/CPI 13003-2023 石油天然气钻采设备高压管汇使用、维护与检验

本文件规定了额定压力为35 MPa～175 MPa石油天然气钻采设备高压管汇及元件使用、维护与检验的要求。 本文件适用于陆上石油天然气钻井、固井、压裂酸化、测试、修井等施工作业用的管汇及管汇元件，海洋石油天然气钻井、固井、压裂酸化、测试、修井等施工作业用的管汇及管汇元件可参照执行

Use, maintenance and inspection of high-pressure manifolds for oil and gas drilling equipment