75.180.10 勘探和钻采设备 标准查询与下载

BS EN ISO 3421:2022 石油和天然气工业 钻井和生产设备 海上导线设计、埋设深度和安装

1   Scope This document specifies the requirements and recommendations for the design, setting depth and installation of conductors for the offshore petroleum and natural gas industries. This document specifically addresses: — design of the conductor, i.e. determination of the diameter, wall thickness, and steel grade; — determination of the setting depth for three installation methods, namely, driving, drilling and cementing, and jetting; — requirements for the three installation methods, including applicability, procedures, and documentation and quality control. This document is applicable to: — platform conductors: installed through a guide hole in the platform drill floor and then through guides attached to the jacket at intervals through the water column to support the conductor, withstand actions, and prevent excessive displacements; — jack-up supported conductors: a temporary conductor used only during drilling operations, which is installed by a jack-up drilling rig. In some cases, the conductor is tensioned by tensioners attached to the drilling rig;

Petroleum and natural gas industries. Drilling and production equipment. Offshore conductor design, setting depth and installation

22/30454941 DC BS EN ISO 15551 石油和天然气工业 钻井和生产设备 第 1 部分：人工举升用电动潜水泵系统 (ISO 15551-1:2015)

BS EN ISO 15551. Petroleum and natural gas industries. Drilling and production equipment - Part 1. Electric submersible pump systems for artificial lift (ISO 15551-1:2015)

BS EN ISO 24200:2022 石油、石化和天然气工业 海上项目散装材料 管道支撑（ISO 24200:2022）

1   Scope This document specifies the requirements for design including shape and dimensions, material as well as strength for pipe support. Applicable pipe size range varies depending on support types. This document covers topside systems for fixed or floating offshore oil and gas projects. This document is applicable to design temperature of support within the range between –46 °C up to 200 °C. This document is limited to metallic pipes, covering the following pipe supports: — clamped shoe; — welded shoe; — U-bolt ; — U-strap ; — bracing for branch connection ; — trunnion and stanchion ; — guide support (guide, hold-down , guide and hold-down , line stop).

Petroleum, petrochemical and natural gas industries - Bulk material for offshore projects - Pipe support (ISO 24200:2022)

EN ISO 19905-3:2022 石油和天然气工业. 移动式海上装置的现场特定评估. 第3部分: 浮动装置

This document specifies requirements and recommendations for the site-specific assessment of mobile floating units for use in the petroleum and natural gas industries. It addresses the installed phase, at a specific site, of manned non-evacuated, manned evacuated and unmanned mobile floating units. This document addresses mobile floating units that are monohull (e.g. ship-shaped vessels or barges); column-stabilized, commonly referred to as semi-submersibles; or other hull forms (e.g. cylindrical/conical shaped). It is not applicable to tension leg platforms. Stationkeeping can be provided by a mooring system, a thruster assisted mooring system, or dynamic positioning. The function of the unit can be broad, including drilling, floatel, tender assist, etc. In situations where hydrocarbons are being produced, there can be additional requirements. This document does not address all site considerations, and certain specific locations can require additional assessment. This document is applicable only to mobile floating units that are structurally sound and adequately maintained, which is normally demonstrated through holding a valid RCS classification certificate. This document does not address design, transportation to and from site, or installation and removal from site. This document sets out the requirements for site-specific assessments, but generally relies on other documents to supply the details of how the assessments are to be undertaken. In general: — ISO 19901‑7 is referenced for the assessment of the stationkeeping system; — ISO 19904‑1 is referenced to determine the effects of the metocean actions on the unit; — ISO 19906 is referenced for arctic and cold regions; — the hull structure and air gap are assessed by use of a comparison between the site-specific metocean conditions and its design conditions, as set out in the RCS approved operations manual; — ISO 13624‑1 and ISO/TR 13624‑2[1] are referenced for the assessment of the marine drilling riser of mobile floating drilling units. Equivalent alternative methodologies can be used; — IMCA M 220 is referenced for developing an activity specific operating guidelines. Agreed alternative methodologies can be used. NOTE RCS rules and the IMO MODU code[13] provide guidance for design and general operation of mobile floating units.

Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 3: Floating units (ISO 19905-3:2021)

ISO 19901-2:2022 石油和天然气工业.海洋结构物的特殊要求.第2部分:抗震设计程序和标准

This document contains requirements for defining the seismic design procedures and criteria for offshore structures; guidance on the requirements is included in Annex A. The requirements focus on fixed steel offshore structures and fixed concrete offshore structures. The effects of seismic events on floating structures and partially buoyant structures are briefly discussed. The site-specific assessment of jack-ups in elevated condition is only covered in this document to the extent that the requirements are applicable. Only earthquake-induced ground motions are addressed in detail. Other geologically induced hazards such as liquefaction, slope instability, faults, tsunamis, mud volcanoes and shock waves are mentioned and briefly discussed. The requirements are intended to reduce risks to persons, the environment, and assets to the lowest levels that are reasonably practicable. This intent is achieved by using: a) seismic design procedures which are dependent on the exposure level of the offshore structure and the expected intensity of seismic events; b) a two-level seismic design check in which the structure is designed to the ultimate limit state (ULS) for strength and stiffness and then checked to abnormal environmental events or the abnormal limit state (ALS) to ensure that it meets reserve strength and energy dissipation requirements. Procedures and requirements for a site-specific probabilistic seismic hazard analysis (PSHA) are addressed for offshore structures in high seismic areas and/or with high exposure levels. However, a thorough explanation of PSHA procedures is not included. Where a simplified design approach is allowed, worldwide offshore maps, which are included in Annex B, show the intensity of ground shaking corresponding to a return period of 1000 years. In such cases, these maps can be used with corresponding scale factors to determine appropriate seismic actions for the design of a structure, unless more detailed information is available from local code or site-specific study. NOTE For design of fixed steel offshore structures, further specific requirements and recommended values of design parameters (e.g. partial action and resistance factors) are included in ISO 19902, while those for fixed concrete offshore structures are contained in ISO 19903. Seismic requirements for floating structures are contained in ISO 19904, for site-specific assessment of jack-ups and other MOUs in the ISO 19905 series, for arctic structures in ISO 19906 and for topsides structures in ISO 19901-3.

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 2: Seismic design procedures and criteria

22/30449659 DC BS EN ISO 19901-4 石油和天然气工业 海上结构的具体要求 第 4 部分：岩土设计考虑因素

BS EN ISO 19901-4. Petroleum and natural gas industries. Specific requirements for offshore structures - Part 4. Geotechnical design considerations

T/CPI 11010-2022 抽油机永磁低速拖动装置

本文件规定了抽油机永磁低速拖动装置的型号、结构、要求、试验方法和验收规则、标志、包装、运输和贮存等。

Permanent magnet low-speed driving device of pumping unit

T/CPI 11012-2022 石油天然气钻采设备 电动压裂泵送设备

本文件规定了电动压裂泵送设备的型式、型号与基本参数、总体要求、试验、检验规则、标志、包装与运输和贮存。

Oil and gas drilling equipment Electric fracturing pumping equipment

T/CPI 11011-2022 石油天然气钻采设备 电动混砂设备

本文件规定了电动混砂设备的型式、型号与基本参数、总体要求、试验、检验规则、标志、包装与运输和贮存。

Electric sand mixing equipment for oil and gas drilling equipment

EN ISO 3421:2022 石油和天然气工业.钻井和生产设备.海上导体设计、设置深度和安装

This document specifies the requirements and recommendations for the design, setting depth and installation of conductors for the offshore petroleum and natural gas industries. This document specifically addresses: — design of the conductor, i.e. determination of the diameter, wall thickness, and steel grade; — determination of the setting depth for three installation methods, namely, driving, drilling and cementing, and jetting; — requirements for the three installation methods, including applicability, procedures, and documentation and quality control. This document is applicable to: — platform conductors: installed through a guide hole in the platform drill floor and then through guides attached to the jacket at intervals through the water column to support the conductor, withstand actions, and prevent excessive displacements; — jack-up supported conductors: a temporary conductor used only during drilling operations, which is installed by a jack-up drilling rig. In some cases, the conductor is tensioned by tensioners attached to the drilling rig; — free-standing conductors: a self-supporting conductor in cantilever mode installed in shallow water, typically water depths of about 10 m to 20 m. It provides sole support for the well and sometimes supports a small access deck and boat landing; — subsea wellhead conductors: a fully submerged conductor extending only a few metres above the sea floor to which a BOP and drilling riser are attached. The drilling riser is connected to a floating drilling rig. The BOP, riser and rig are subject to wave and current actions while the riser can also be subject to VIV. This document is not applicable to the design of drilling risers.

Petroleum and natural gas industries - Drilling and production equipment - Offshore conductor design, setting depth and installation (ISO 3421:2022)

T/CPI 24001-2022 渤海海域固定平台 挡风墙设计推荐作法

本文件规定了渤海海域海上油气田开发固定平台挡风墙设计的基本要求。

Recommended practices for design of windshield walls for fixed platforms in the Bohai Sea area

T/CPI 11015-2022 录井钢丝

本文件规定了录井钢丝的分类与标记、要求、检验、包装、标志与质量证明书、验收、运输与贮存、使用与报废的内容。

Mud logging wire

T/CPI 11014-2022 石油天然气钻采设备 螺杆钻具技术与应用规范

本文件规定了螺杆钻具的分类、型号、基本尺寸、连接螺纹、技术要求、试验方法、检验规则、标志、包装、运输、贮存、使用规范、性能检查与磨损评定、维护及保养等。

Oil and gas drilling equipment screw drilling technology and application specifications

T/CPI 11013-2022 连续油管作业通用井下工具

本标准包含连接器、止回阀、丢手接头、循环阀、马达头和扶正器。 本标准规定了连续油管作业通用井下工具的型号编制方法、参数规格、技术要求、检验及试验方法、检验规则、标志、包装、运输和贮存、健康安全环境控制要求等。

Common Downhole Tools for Coiled Tubing Operations

T/CPI 12001-2022 远程控制固井水泥头

本文件规定了远程控制固井水泥头型号表示方法、技术要求、试验和检验规则、涂装、标志、包装、运输、贮存等。

Remote control cementing head

T/CPI 13001-2022 水下油气设备外压试验方法

本文件规定了水下油气设备外压试验的试验装置、试验准备、试验程序、验收准则、试验报告等要求。

External pressure test method for underwater oil and gas equipment

ISO 3421:2022 石油和天然气工业.钻井和生产设备.海上导体设计、设置深度和安装

This document specifies the requirements and recommendations for the design, setting depth and installation of conductors for the offshore petroleum and natural gas industries. This document specifically addresses: — design of the conductor, i.e. determination of the diameter, wall thickness, and steel grade; — determination of the setting depth for three installation methods, namely, driving, drilling and cementing, and jetting; — requirements for the three installation methods, including applicability, procedures, and documentation and quality control. This document is applicable to: — platform conductors: installed through a guide hole in the platform drill floor and then through guides attached to the jacket at intervals through the water column to support the conductor, withstand actions, and prevent excessive displacements; — jack-up supported conductors: a temporary conductor used only during drilling operations, which is installed by a jack-up drilling rig. In some cases, the conductor is tensioned by tensioners attached to the drilling rig; — free-standing conductors: a self-supporting conductor in cantilever mode installed in shallow water, typically water depths of about 10 m to 20 m. It provides sole support for the well and sometimes supports a small access deck and boat landing; — subsea wellhead conductors: a fully submerged conductor extending only a few metres above the sea floor to which a BOP and drilling riser are attached. The drilling riser is connected to a floating drilling rig. The BOP, riser and rig are subject to wave and current actions while the riser can also be subject to VIV. This document is not applicable to the design of drilling risers.

Petroleum and natural gas industries — Drilling and production equipment — Offshore conductor design, setting depth and installation

BS EN ISO 10423:2022 石油和天然气工业 钻井和生产设备 井口和采油树设备

1   Scope This document specifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, and purchasing of wellhead and tree equipment for use in the petroleum and natural gas industries. This document does not apply to field use or field testing. This document does not apply to repair of wellhead and tree equipment except for weld repair in conjunction with manufacturing. This document does not apply to tools used for installation and service (e.g. running tools, test tools, wash tools, wear bushings, and lubricators). This document supplements API Spec 6A, 21 st edition (2018), the requirements of which are applicable with the exceptions specified in this document.

Petroleum and natural gas industries. Drilling and production equipment. Wellhead and tree equipment

T/CPSI 01301-2022 油气井用高抗挤套管

高抗挤套管的制造方法、最小抗挤强度、残余应力、材料性能、高抗挤套管的分级等、尺寸、质量、公差、管端和缺陷、检验与试验

High collapse casing for oil and gas wells

EN ISO 24200:2022 石油、石化和天然气工业.海上项目用散装材料.管支架

This document specifies the requirements for design including shape and dimensions, material as well as strength for pipe support. Applicable pipe size range varies depending on support types. This document covers topside systems for fixed or floating offshore oil and gas projects. This document is applicable to design temperature of support within the range between –46 °C up to 200 °C. This document is limited to metallic pipes, covering the following pipe supports: — clamped shoe; — welded shoe; — U-bolt; — U-strap; — bracing for branch connection; — trunnion and stanchion; — guide support (guide, hold-down, guide and hold-down, line stop).

Petroleum, petrochemical and natural gas industries - Bulk material for offshore projects - Pipe support (ISO 24200:2022)