共找到 2513 条与 金属材料机械试验 相关的标准,共 168 页
GB/T37306的本部分规定了应应用于变幅疲劳试验的循环计数和数据和减的方法。 对于每个试验或试验系列,循环计数都是约束性的,数据缩减的各种方法则是可选择采用的。 本部分支持包含变幅疫劳试验总则、试验方法和报告要求的ISO12110-1。 本部分适用于所有载荷类型,术语载荷?指的是力、应力或应变。 下列各项不属于本部分的考虑范围之内: ——出现孤立的过载或欠载现象的恒幅疲劳试验; ——零部件或结构件的试验; ——环境影响,如腐蚀、与温度时间相关的蠕变导致频谤和波形的影响; ——多轴加载。 注1:当进行恒定振幅或变幅受控加载多轴试验时,相位是至关重要的。 注2:循环时的频率变化不属于本部分的范围,后续各章条只处理恒定频率循环的情况。
Metallic materials—Fatigue testing—Variable amplitude fatiguetesting—Part 2: Cycle counting and related data reduction methods
Metallic materials—Fatigue testing—Variable amplitude fatigue testing—Part 1: General principles, test method and reporting requirements
Mechanical properties measurement—Room temperature tensile test of Ag-and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors
本标准规定了GB/T 15574中定义的型钢、棒材、盘条、钢板和管材的力学性能试验用试样的标识、取样位置和制备的要求。 本标准适用于钢及钢产品的力学性能取样和试样制备。如果合同中注明,本标准也适用于其他金属产品。这些试料和试样可根据相关的产品标准、材料标准或试验标准开展试验。
Steel and steel products.Location and preparation of samples and test pieces for mechanical testing
本标准规定了采用短梁法测定纤维金属层板层间剪切强度的术语和定义、试验原理、试验设备、试样、状态调节、试验过程、计算及结果表示、试验报告。附录A给出了双梁法以供参考。 本标准适用于能发生层间剪切失效的热固性或热塑性连续纤维增强金属层板。 本标准不适用于确定设计参数,但可用于筛选材料或作为质量控制的试验。
Fiber metal laminates.Determination of interlaminar shear strength by short-beam method
GB/T 230的本部分规定了标尺为A、B、C、D、E、F、G、H、K、15N、30N、45N、15T、30T和45T的金属材料洛氏硬度和表面洛氏硬度的试验方法。 本部分适用于固定式和便携式洛氏硬度计。对于特定的材料或产品,适用其他特定标准,例如:GB/T 3849.1、GB/T 9097。
Metallic materials.Rockwell hardness test.Part 1:Test method
本标准规定了金属薄板薄带十字形试样双向拉伸试验方法的术语和定义、符号及说明、试验原理、试样、试验方法、双向应力-应变曲线的测定和试验报告。 本标准适用于板厚不小于0.1 mm且不大于0.08倍试样臂宽(见图1)的十字形试样进行双向拉伸试验测量金属板材应力-应变曲线的试验。试验温度范围为10 ℃~35 ℃。其他温度条件下的双向拉伸试验也可参照本标准执行。
Metallic materials.Sheet and strip.Biaxial tensile testing method using a cruciform test piece
Steel—Drop-weight tear tests method
Determination of anti-slip coefficient at bolted connect steel plates' surfaces
Metallic materials—Sheet and strip—Dent resistance test method
Copper and copper alloy materials—Tensile testing at room temperature
Metallic Materials—Sheet and strip—Dent resistance test method
Shearing and riveting test method of wires and rods for the aluminum and aluminum-alloy rivets
Contractile strain ratio testing of metal materials tubing
Metallic materials—Hardness testing—Ultrasonic contact impedance method
Metallic materials—Verification of the alignment of testing machines
Metallic materials—High strain rate compression test method at ambient temperature
本标准规定了测定圆形横蕉面金属管碍性变形能力的压扁试验方法,也可用来揭示其缺陷。 除相关产品标准规定以外,本标准适用于外径不超过600 mm 目壁厚不超过外径15%的金属管。 2 符号.名称和单位
Metallic materials—Tube—Flattening test
Metallic materials—Fatigue testing—Fatigue crack growth method
Metallic materials—Tensile testing—Determination of thickness reduction ratio for rectangular specimen
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号