77.080.10 铁 标准查询与下载

BS EN 1563:2018 创立 球墨铸铁

Founding. Spheroidal graphite cast irons

EN 1563:2018 成立.球状石墨铸铁

Founding - Spheroidal graphite cast irons

BS ISO 1083:2018 球状石墨铸铁 分类

1   Scope This document defines the grades and the corresponding requirements for spheroidal graphite cast irons . This document specifies two groups of spheroidal graphite cast iron grades by a classification based on mechanical properties measured on machined test pieces prepared from cast samples . The first group deals mainly with ferritic to pearlitic grades. The second group deals with solid-solution strengthened ferritic grades. This document also gives an informative classification as a function of hardness. This document does not apply to the following: — spheroidal graphite cast irons used for pipes, fittings and accessories which are specified in accordance with ISO 2531 and ISO 7186; — highly alloyed (austenitic) spheroidal cast irons which are specified in accordance with ISO 2892; — ausferritic cast irons which are specified in accordance with ISO 17804.

Spheroidal graphite cast irons. Classification

DIN EN ISO 945-1:2018 铸铁微观结构.第1部分:通过目视分析进行石墨的分类(ISO 945-1-2017); 德文版本EN ISO 945-1-2018

This document specifies a method of classifying the microstructure of graphite in cast irons by comparative visual Analysis provides information about the method of graphite classification. It is not intended to give information on the suitability of cast iron types and grades for any particular application.

Microstructure of cast irons - Part 1: Graphite classification by visual analysis (ISO 945-1:2017); German version EN ISO 945-1:2018

ISO 1083:2018 球墨铸铁.分类

This document defines the grades and the corresponding requirements for spheroidal graphite cast irons. This document specifies two groups of spheroidal graphite cast iron grades by a classification based on mechanical properties measured on machined test pieces prepared from cast samples. The first group deals mainly with ferritic to pearlitic grades. The second group deals with solid-solution strengthened ferritic grades. This document also gives an informative classification as a function of hardness. This document does not apply to the following: — spheroidal graphite cast irons used for pipes, fittings and accessories which are specified in accordance with ISO 2531 and ISO 7186; — highly alloyed (austenitic) spheroidal cast irons which are specified in accordance with ISO 2892; — ausferritic cast irons which are specified in accordance with ISO 17804.

Spheroidal graphite cast irons - Classification

T/CFA 0202050201.03-2018 球墨铸铁件用生铁

本标准规定了球墨铸铁件用生铁的化学成分和牌号及相关技术要求、试验方法、检验规则、质量证  明书及运输储存要求等。  

Pig iron for ductile iron castings

T/CFA 0202050201-2018 铸造用高纯生铁

本标准规定了铸造用高纯生铁的化学成分和牌号及相关技术要求、试验方法、检验规则、质量证明书及运输储存要求等。

High purity pig iron for foundry

ISO 945-1:2017 铸铁微观结构.第1部分:通过目视分析进行石墨的分类

Microstructure of cast irons - Part 1: Graphite classification by visual analysis

GSO ISO/TR 16078:2017 铸铁 铸造缺陷的分类和命名

This Technical Report gives the classification and designation of casting imperfections. It mainly applies to iron castings produced in sand moulds. It can, however, also be applied for other cast materials and other casting techniques. Specific examples are given in Table 3 In order to avoid any confusion, the types of imperfection are defined with explanations and illustrations where necessary. NOTE This technical report does not contain any information regarding the causes of the imperfection and possible solutions to avoid the imperfection. For this, the publications as listed in the bibliography should be consulted.

Cast Irons - Classification and designation of casting imperfections

WW/T 0074-2017 室外铁质文物缓蚀工艺规范

Specifications for Corrosion Inhibition Process for Outdoor Iron Cultural Relics

T/CFA 0202050201.02-2017 铸造用钒钛生铁

1.本标准按含钒量和含钛量将钒钛生铁分为 6 个牌号，给出了各牌号成分。 2.本标准规定了钒钛生铁的化学分析方法。

Pig iron containing vanadium and titanium in foundry

ISO 16112:2017 压实石墨(蠕墨)铸铁. 分类

Compacted (vermicular) graphite cast irons - Classification

BS PD ISO/TS 10719:2016 铸铁. 非化合碳含量的测定. 感应炉燃烧后的红外吸收法

Cast irons. Determination of non-combined carbon content. Infrared absorption method after combustion in an induction furnace

GSO ISO/TR 10809-2:2016 铸铁 第2部分：焊接

The purpose of this part of ISO/TR 10809 is to assist the design engineer to understand and to acquire knowledge of how the family of cast iron materials can be welded and to utilize this technology to its full advantage in selecting the most appropriate technique for a particular cast iron. Because the application of welding technology and the metallurgical implications of welding are not scientific disciplines normally taught to engineering students, such users often have limited knowledge of the fundamentals underpinning welding technology for cast irons. This part of ISO/TR 10809 explains what can be achieved, what cannot be achieved and why. It is not designed to be a textbook of welding technology. It helps users to select the most appropriate welding process and conditions for a specific application. This part of ISO/TR 10809 covers production (including finishing and joint welding) and repair welding.

Cast irons -- Part 2: Welding

ISO/TS 10719:2016 铸铁. 非化合碳含量的测定. 感应炉燃烧后的红外吸收法

Cast irons - Determination of non-combined carbon content - lnfrared absorption method after combustion in an induction furnace

ISO/TS 10719:1994 铸铁. 非化合碳含量的测定. 感应炉燃烧后的红外吸收法

Cast irons - Determination of non-combined carbon content - lnfrared absorption method after combustion in an induction furnace

BS PD ISO/TR 945-3:2016 铸铁的微观结构. 矩阵结构

Microstructure of cast irons. Matrix structures

DB21/T 2652-2016 地理标志产品 本溪人参铁

Geographical indication product Benxi ginseng iron

ISO/TR 945-3:2016 铸铁的微观结构.第3部分：基体结构

Microstructure of cast irons- Part 3:Matrix structures

16/30333750 DC BS ISO 16112 蠕墨铸铁 分类

BS ISO 16112. Compacted (vermicular) graphite cast irons. Classification