77.140.20 不锈钢 标准查询与下载

T/FSMA 001-2022 不锈钢水管安装规程

前言 1 范围 2 规范性引用文件 3 术语和定义 4 水管与管件 5 设计 6 施工 7 附件 8 验收 9 巡查维护 附录 A 卡压式连接不锈钢水管安装方法(卡压钳) 附录 B 环压式连接不锈钢水管安装方法 附录 C 沟槽式连接不锈钢水管安装方法 附录 D 分水器的结构型式和规格尺寸

Stainless steel water pipe installation regulations

ASTM A666-23 退火或冷加工奥氏体不锈钢薄板、带材、板材和扁钢的标准规范

1.1 This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions for various structural, pressure vessel, magnetic, cryogenic, and heat-resisting applications. 1.2 The application of this specification, or the use of material covered by this specification does not automatically allow usage in pressure vessel applications. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

T/HGMIF 014-2023 绿色设计产品评价技术规范 焊接不锈钢管

根据GB/T32161《生态设计产品评价通则》及有关要求，焊接不锈钢管的评价指标从产品全生命周期中对资源和能源的消耗、对生态环境和人体健康影响的角度进行选取，包括资源属性、能源属性、环境属性、产品属性指标，按照全生命周期的理念，在产品设计开发阶段系统考虑原材料选用、生产、销售、使用、回收、处理等各个环节对资源环境造成的影响，力求产品在全生命周期中最大限度降低资源消耗、尽可能少用或不用含有害物质的原材料，减少污染物产生和排放，从而实现环保的目的。评价指标设计主要考虑以现执行的国家标准、行业标准为判定依据，根据产品和行业特点，以评价筛选生态设计产品为目的，在测试及征询行业专家、生产厂商意见的基础上，科学、合理地确定指标基准值。

Technical specification for green-design product assessment Welded stainless steel pipes

ASTM A484/A484M-23 不锈钢棒材、钢坯和锻件的一般要求标准规范

1.1 This specification2 covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under each of the following specifications issued by ASTM: Specifications A276/A276M, A314, A458, A477, A479/A479M, A564/A564M, A565/A565M, A582/A582M, A638/A638M, A705/A705M, and A831/A831M. 1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent. 1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1. 1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A480/A480M. 1.5 General requirements for wire products in coils are covered in Specification A555/A555M. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

ASTM G108-23 检测AISI 304和304L型不锈钢敏化的电化学反应（EPR）的标准试验方法

Standard Test Methods for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels

BS 6744:2023 不锈钢棒 混凝土加固 要求及测试方法

1   Scope This British Standard specifies requirements and test methods for solid stainless steel bars used for the reinforcement of concrete. It is applicable to ribbed stainless reinforcing steel bars in grade 500. It is applicable to bars in which the ribs have been formed by the cold working or hot rolling processes. NOTE Annex A specifies a test method for determining the corrosion resistance of stainless reinforcing steel in chloride contaminated concrete. Informative annexes give guidance on durability (Annex B), magnetic properties (Annex C), coefficients of thermal expansion (Annex D), constitutive relationship (Annex E), welding (Annex F), performance at elevated temperatures (Annex G) and quality assurance (Annex H). This British Standard is not applicable to stainless reinforcing steel bars produced from material whose metallurgical history is not known and fully documented. It is not applicable to other uses of steel in concrete, such as plain bars and grades 200 MPa and ribbed bars above grade 500 MPa, which are covered by other standards. This is with the exception of 500 MPa bar and 650 MPa ribbed bar which are now in an informative annex (Annex I). The standard is open to other strength grades of ribbed bar on the basis that the designers know that these are outside normal UK practice and, ...

Stainless steel bars. Reinforcement of concrete. Requirements and test methods

KS D 7142-2022 高锰钢焊条

Covered electrodes for high manganese steel

ASTM A1022/A1022M-22a 混凝土钢筋用变形和普通不锈钢丝和焊接丝的标准规范

1.1 This specification covers stainless steel wire and welded wire reinforcement produced from hot-rolled stainless steel rod. The stainless steel wire is cold-worked, drawn or rolled, plain (non-deformed) or deformed or a combination of deformed and plain. It is used as concrete reinforcement for applications requiring resistance to corrosion or controlled magnetic permeability, or both. Common wire sizes and dimensions are found in this specification. Actual wire sizes are not restricted to those shown in the tables. 1.2 A supplementary requirement (S1) is provided and shall apply only when specified by the purchaser. In order to obtain a corrosion tested or controlled magnetic permeability product, steel conforming to Supplementary Requirement S1 should be ordered. 1.3 The chemical composition of the steel (stainless alloy) shall be selected for suitability to the application involved by agreement between the manufacturer and the purchaser. Unless otherwise specified by the purchaser, Specification A276 shall be used for chemical requirements. The UNS designations are to be included with the type number and noted in brackets. Examples of austenitic stainless steel designations are Type 304 [S30400], 304L [S30403], 316 [S31600], 316L [S31603], 316N [S31651], 316LN [S31653] and examples of duplex stainless steel designations are Type 2205 [S32205] and 329 [S32900]. NOTE 1—Only austenitic and duplex stainless steels are usually recommended for use as reinforcement in concrete because of their high corrosion resistance. Austenitic stainless steels have good general corrosion resistance, strength characteristics which can be improved by cold working, good toughness and ductility properties at low temperatures, and low magnetic permeability. Duplex stainless steels have generally a corrosion resistance greater than that of most austenitic steels and are magnetic. Other stainless steels with different chemical compositions than the series and types mentioned above, may be used for less restrictive applications. 1.4 Wire for welded wire reinforcement is generally manufactured at 75 ksi [520 MPa] yield strength level. Other strength levels shall be by agreement between the purchaser and manufacturer. NOTE 2—The term used to refer to yield strength levels are the same as those in ASTM Standards for welded wire reinforcement. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Deformed and Plain Stainless Steel Wire and Welded Wire for Concrete Reinforcement

YB/T 6019-2022 模具钢超声检测方法

本文件规定了模具钢超声检测的一般要求、对比试块、检测仪器和设备、检测条件和方法、缺陷的测定、质量分级和检测报告。 本文件适用于厚度不小于6 mm的模具钢的纵波直入射反射法手动和自动超声检测。圆棒类模具钢和其他非模具钢锻件、板材等的超声检测可参照本文件执行。

Ultrasonic testing method of mold steel

ASTM A484/A484M-22 不锈钢棒、钢坯和锻件一般要求的标准规范

1.1 This specification2 covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under each of the following specifications issued by ASTM: Specifications A276/A276M, A314, A458, A477, A479/A479M, A564/A564M, A565/A565M, A582/A582M, A638/A638M, A705/A705M, and A831/A831M. 1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent. 1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1. 1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A480/A480M. 1.5 General requirements for wire products in coils are covered in Specification A555/A555M. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

ASTM A1022/A1022M-22 混凝土钢筋用变形和普通不锈钢丝和焊接丝的标准规范

Standard Specification for Deformed and Plain Stainless Steel Wire and Welded Wire for Concrete Reinforcement

ASTM A693-22 沉淀硬化不锈钢和耐热钢板材、薄板和带材标准规范

1.1 This specification2 covers precipitation-hardening stainless steel plate, sheet, and strip. The mechanical properties of these steels are developed by suitable low-temperature heat treatments generally referred to as precipitation hardening. 1.2 These steels are used for parts requiring corrosion resistance and high strength at room temperature or at temperatures up to 600 °F (315 °C). Some of these steels are particularly suitable for moderate to severe drawing and forming in the solution-treated condition. Others are capable of mild forming only. They are suitable for machining in the solution-annealed condition, after which they may be hardened to the mechanical properties specified in this standard without danger of cracking or distortion. 1.3 The values stated in inch-pound units are to be regarded as the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

KS D 3531-2022 耐蚀耐热高温合金棒材

Corrosion-resisting and heat-resisting superalloy bars

KS D 0270-2022 不锈钢和/或临界缝隙温度的测试方法

Test methods for critical crevice temperature and/of stainless steels

KS D 3532-2022 耐蚀耐热高温合金板材

Corrosion－resisting and heat－resisting superalloy plates and sheets

KS D 3747-2022 耐热耐腐蚀阀门用耐热铸钢

Heat resistant cast steels for heat and corrosion resistant valve

KS D 4126-2022 耐热、耐腐蚀高温合金铸件

Heat-resisting and corrosion-resisting superalloy castings

KS D 3591-2022 油回火硅锰合金钢弹簧钢丝

Oil tempered silicon manganese alloy steel spring wires

KS D 4125-2022 低温压力容器用碳钢和合金钢锻件

Carbon and alloy steel forgings for pressure vessels for low-temperature service

KS D 3732-2022 耐热钢板和薄板

Heat-resisting steel plates and sheets