77.140.20 不锈钢 标准查询与下载

ASTM A493-23 冷镦和冷锻用不锈钢丝和线材标准规范

Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

ASTM A965/A965M-23 压力和高温部件用奥氏体钢锻件标准规范

Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts

ASTM A1016/A1016M-23 铁素体合金钢、奥氏体合金钢和不锈钢管的一般要求标准规范

Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes

ASTM A314-23 锻造用不锈钢坯料和棒材标准规范

Standard Specification for Stainless Steel Billets and Bars for Forging

KS D ISO 18632-2023 合金钢锰含量的测定电位滴定法或目视滴定法

Alloyed steel — Determination of manganese — Potentiometric or visual titration method

ISO 16143-4:2023 一般用途不锈钢 第 4 部分：光亮产品

Stainless steels for general purposes — Part 4: Bright products

ISO/DIS 17650:2023 低合金钢 锰、磷、铬、镍、钼、钴、铜、钒、钛、砷和锡的测定 电感耦合等离子体原子发射光谱法

Low-alloyed steel — Determination of Mn, P, Cr, Ni, Mo, Co, Cu, V, Ti, As and Sn — Inductively coupled plasma atomic emission spectrometric method

ASTM A484/A484M-23a 不锈钢棒材、坯料、型材和锻件的一般要求标准规范

Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings

ASTM A276/A276M-23 不锈钢棒材和型材标准规范

1.1 This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1). It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types (Note 2) for general corrosion resistance and high-temperature service are covered in a separate specification. NOTE 1—For bars for reforging, see Specification A314. NOTE 2—For free-machining stainless bars designed especially for optimum machinability, see Specification A582/A582M. NOTE 3—There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol. 02.04. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Stainless Steel Bars and Shapes

ISO/FDIS 11973:2023 一般用途的耐热铸钢和合金

Heat-resistant cast steels and alloys for general applications

T/GXAS 485-2023 红土镍矿生产不锈钢单位产品能耗限额

本文件界定了红土镍矿生产不锈钢单位产品能耗限额涉及的术语和定义，规定了红土镍矿生产不锈钢主要工序单位产品能耗限额等级、限定值和准入值的技术要求、统计范围和计算方法。  本文件适用于广西行政区域内以红土镍矿为原料冶炼不锈钢产品生产企业的能耗计算、控制和评价，以及对新建、改建和扩建项目的能耗控制。

The norm of energy consumption per unit product of stainless steel produced from laterite nickel

ASTM A1018/A1018M-23 高强度低合金、具有改进成形性的高强度低合金钢和超高强度结构用热轧、商用、拉伸、碳素厚卷材用薄钢板和带材标准规范

1.1 This specification covers hot-rolled, heavy-thickness coils beyond the size limits of Specification A1011/A1011M. 1.2 The product is available in six designations: Commercial Steel, Drawing Steel, Structural Steel, High-Strength Low-Alloy Steel, High-Strength Low-Alloy Steel with Improved Formability, and Ultra-High Strength Steel. 1.3 This material is available only in coils described as follows: Product Size Limits, Coils Only Width, in. [mm] Thickness, in. [mm] Strip Over 8 to 12, incl [Over 200 to 300] 0.230 to 1.000, incl [From 6.0 through 25] Sheet Over 12 [Over 300] 0.230 to 1.000, incl [From 6.0 through 25] NOTE 1—The changes in width limits with the publication of A635/ A635M – 06a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide as that material is now covered by Specification A568/A568M – 06a. The purchaser is advised to discuss this change with the supplier. 1.4 Sheet and strip in coils of sizes noted in 1.3 are covered by this specification only with the following provisions: 1.4.1 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming. 1.4.2 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils). Plate converted from coils is no longer governed by this sheet steel specification and since this material is now a plate, the requirements of the appropriate plate specification shall apply, except in cases where there is a conflict between the requirements of the plate specification and this specification. In these cases, the more restrictive limits of either specification shall apply. 1.4.3 The dimensional tolerances of Specification A635/ A635M are applicable to material produced to this specification. 1.4.4 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formabilit

ASTM A1011/A1011M-23 具有改进成形性和超高强度的高强度低合金结构热轧薄钢板和钢带

1.1 This specification covers hot-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, and ultra-high strength steel sheet and strip, in coils and cut lengths. 1.2 Hot rolled steel sheet and strip is available in the designations as listed in 4.1. 1.3 This specification is not applicable to the steel covered by Specification A635/A635M. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

T/FSMA 001-2022 不锈钢水管安装规程

前言 1 范围 2 规范性引用文件 3 术语和定义 4 水管与管件 5 设计 6 施工 7 附件 8 验收 9 巡查维护 附录 A 卡压式连接不锈钢水管安装方法(卡压钳) 附录 B 环压式连接不锈钢水管安装方法 附录 C 沟槽式连接不锈钢水管安装方法 附录 D 分水器的结构型式和规格尺寸

Stainless steel water pipe installation regulations

ASTM A1049/A1049M-18(2023) 压力容器及相关部件用铁素体/奥氏体（双相）不锈钢锻件标准规范

1.1 This specification covers ferritic/austenitic (duplex) stainless steel forgings for boilers, pressure vessels, and associated equipment in grades that are also found in Specification A182/A182M. 1.2 The purchaser may specify in the order or contract any appropriate supplementary requirements that are provided in Specification A788/A788M. 1.3 Unless the order specifies the applicable “M” specification designation the material shall be furnished to the inchpound units. 1.4 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Stainless Steel Forgings, Ferritic/Austenitic (Duplex), for Pressure Vessels and Related Components

T/HGMIF 014-2023 绿色设计产品评价技术规范 焊接不锈钢管

根据GB/T32161《生态设计产品评价通则》及有关要求，焊接不锈钢管的评价指标从产品全生命周期中对资源和能源的消耗、对生态环境和人体健康影响的角度进行选取，包括资源属性、能源属性、环境属性、产品属性指标，按照全生命周期的理念，在产品设计开发阶段系统考虑原材料选用、生产、销售、使用、回收、处理等各个环节对资源环境造成的影响，力求产品在全生命周期中最大限度降低资源消耗、尽可能少用或不用含有害物质的原材料，减少污染物产生和排放，从而实现环保的目的。评价指标设计主要考虑以现执行的国家标准、行业标准为判定依据，根据产品和行业特点，以评价筛选生态设计产品为目的，在测试及征询行业专家、生产厂商意见的基础上，科学、合理地确定指标基准值。

Technical specification for green-design product assessment Welded stainless steel pipes

ASTM A484/A484M-23 不锈钢棒材、钢坯和锻件的一般要求标准规范

1.1 This specification2 covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under each of the following specifications issued by ASTM: Specifications A276/A276M, A314, A458, A477, A479/A479M, A564/A564M, A565/A565M, A582/A582M, A638/A638M, A705/A705M, and A831/A831M. 1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent. 1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1. 1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A480/A480M. 1.5 General requirements for wire products in coils are covered in Specification A555/A555M. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

ASTM A666-23 退火或冷加工奥氏体不锈钢薄板、带材、板材和扁钢的标准规范

1.1 This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions for various structural, pressure vessel, magnetic, cryogenic, and heat-resisting applications. 1.2 The application of this specification, or the use of material covered by this specification does not automatically allow usage in pressure vessel applications. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

ASTM G108-23 检测AISI 304和304L型不锈钢敏化的电化学反应（EPR）的标准试验方法

Standard Test Methods for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels

BS 6744:2023 不锈钢棒 混凝土加固 要求及测试方法

1   Scope This British Standard specifies requirements and test methods for solid stainless steel bars used for the reinforcement of concrete. It is applicable to ribbed stainless reinforcing steel bars in grade 500. It is applicable to bars in which the ribs have been formed by the cold working or hot rolling processes. NOTE Annex A specifies a test method for determining the corrosion resistance of stainless reinforcing steel in chloride contaminated concrete. Informative annexes give guidance on durability (Annex B), magnetic properties (Annex C), coefficients of thermal expansion (Annex D), constitutive relationship (Annex E), welding (Annex F), performance at elevated temperatures (Annex G) and quality assurance (Annex H). This British Standard is not applicable to stainless reinforcing steel bars produced from material whose metallurgical history is not known and fully documented. It is not applicable to other uses of steel in concrete, such as plain bars and grades 200 MPa and ribbed bars above grade 500 MPa, which are covered by other standards. This is with the exception of 500 MPa bar and 650 MPa ribbed bar which are now in an informative annex (Annex I). The standard is open to other strength grades of ribbed bar on the basis that the designers know that these are outside normal UK practice and, ...

Stainless steel bars. Reinforcement of concrete. Requirements and test methods