77.140.30 承压钢 标准查询与下载

CNS 2905-1997 弹簧钢钢料

本标准适用于以热加工成形制造之弹簧，如迭板弹簧、螺旋弹簧 扭力杆等用之弹簧钢料（以下简称钢料）。

Spring steels

BS EN 10120:1997 焊接储气瓶用钢薄板材及带材

1.1 This European Standard specifies requirements for hot-rolled sheet and strip up to 5 mm thickness, made of steels listed in table 1, and intended for manufacturing welded gas cylinders. 1.2 The general technid delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard. 1.3 This European Standard does not apply to sheet and strip made of - general structural steels (see EN 10025); - non-doy and doy steels for pressure vessels (see EN 100281 to 1002?-6); - low carbon non-doy steels for cold forming (see EN 10111 and EN 10130); - steels with a high yield strength for cold forming (see EN 10149); - cold-rolled strip up to 600 mm wide of low carbon non-doy steels (see EN 101%); - steels for simple pressure vessels (see EN 10207).

Steel sheet and strip for welded gas cylinders

NF A36-211:1997 焊接气体气缸用薄钢板和带材

Steel sheet and strip for welded gas cylinders.

ASTM A203/A203M-97 压力容器板 合金钢 镍标准规范

1.1 This specification covers nickel-alloy steel plates intended primarily for welded pressure vessels. 1.2 Plates under this specification are available with four strength levels and two nickel compositions as follows: Nominal Yield Tensile Nickel Strength, Strength, Content min, ksi min, ksi Grade % [MPa] [MPa] A 2.25 37 [255] 65 [450] B 2.25 40 [275] 70 [485] D 3.50 37 [255] 65 [450] E 3.50 40 [275] 70 [485] F 3.50 2 in.[50 mm] and under 55 [380] 80 [550] Over 2 in.[50 mm] 50 [345] 75 [515] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements. However, current practice normally limits the maximum thickness of plates furnished under this specification as follows: Maximum Thickness, Grade in. [mm] A 6 [150] B 6 [150] D 4 [100] E 4 [100] F 4 [100] 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel

NF A36-205-6:1997 压力容器用钢制扁平产品.第6部分:可焊接淬火和回火细粒钢

Flat products made of steels for pressure purposes. Part 6 : weldable fine grain steels quenched and tempered.

NF A36-205-5:1997 压力钢制平面产品.第5部分:可焊接热轧晶粒钢

Flat products made of steels for pressure purposes. Part 5 : weldable fine grain steels thermomechanically rolled.

CNS 8700-1996 压力容器用淬火–回火合金钢锻钢件

本标准适用于考虑焊接性之压力容器及其零组件，并经淬火–回火之合金钢锻钢件（以下简称为锻钢件）。备考：本标准采用 国际单位制（SI），｛ ｝内之单位及数值仅供参考。

Quenched and Tempered Alloy Steel Forgings for Pressure Vessels

CNS 8702-1996 压力容器用不锈钢锻钢件

Stainless Steel Forgings for Pressure Vessels

CNS 11067-1996 低温压力容器用碳钢及合金钢锻钢件

本标准适用于考虑焊接性，用在低温之压力容器及其零件之碳钢及合金钢锻钢件（以下简称为锻纲件）。备考：本标准采用国际单位制（SI），｛ ｝ 内之单位及数值仅供参考。

Carbon and Alloy Steel Forgings for Pressure Vessels for Low Temperature Service

CNS 8699-1996 压力容器用碳钢锻钢件

本标准适用于考虑焊接性之中温或常温压力容器及零组件之碳钢锻钢件（以下简称为锻钢件）。备考：本标准采用 国际单位制（SI），｛ ｝内之单位及数值仅供参考。

Carbon Steel Forgings for Pressure Vessels

CNS 8701-1996 高温压力容器用合金钢锻钢件

本标准适用于考虑焊接性之高温压力容器及零组件之合金钢锻钢件（以下简称为锻钢件）。备考：本标准采用 国际单位制（SI），｛ ｝内之单位及数值仅供参考。

Alloy Steel Forgings for Pressure Vessels for High Temperature Service

BS EN 10213-4:1996 压力用途的钢铸件的交付技术状态.第4部分:奥氏体钢和奥氏体-铁素体钢的等级

According to the general delivery conditions of EN 10213-1 this standard specifies the chemical and mechanical requirements to be met under specific inspection of austenitic and austenitic-ferritic grades.

Technical delivery conditions for steel castings for pressure purposes - Austenitic and austenitic-ferritic steel grades

BS EN 10213-2:1996 压力用途的钢铸件的交付技术状态.第2部分:环境温度和高温下使用钢的等级

In accordance with the general delivery conditions of EN 10213-1 this standard specifies the chemical and mechanical requirements to be met under specific inspection of steel grades for use at room temperature and elevated temperatures.

Technical delivery conditions for steel castings for pressure purposes - Steel grades for use at room temperature and at elevated temperature

BS EN 10213-1:1996 压力用途的钢铸件交付技术状态.总则

This European Standard applies to steel castings for pressure-containing parts. It includes materials which are used for the manufacture of components subject to pressure vessel construction codes. This standard relates to castings manufactured from unalloyed and alloyed steel grades (characterized by their composition and mechanical properties). Part 1 specifies general technical delivery conditions. The standard comprises three other Parts specifying requirements for: - steel grades for use at room and elevated temperatures (see EN 10213-2); - steel grades for use at low temperatures (see EN 10213-3); - austenitic and austenitic-ferritic steel grades (see EN 10213-4). In cases where castings are joined by welding by the founder, this EN applies. In cases where castings are welded: - to wrought products (plates, tubes, forgings...); - or by non-founders; this European Standard does not apply.

Technical delivery conditions for steel castings for pressure purposes - General

BS EN 10213-3:1996 压力用途的钢铸件交付技术状态.低温下使用的钢

In accordance to the general delivery conditions of EN 10213-1 this standard specifies the chemical and mechanical requirements to be met under specific inspection of steel grades for use at low temperatures.

Technical delivery conditions for steel castings for pressure purposes - Steels for use at low temperatures

NF A32-055-2:1996 压力用途的钢铸件的交货技术条件.第2部分:室温度和高温下使用的钢的等级

Technical delivery conditions for steel castings for pressure purposes. Part 2 : steel grades for use at room temperature and elevated temperatures.

NF A32-055-1:1996 压力用途的钢铸件的交货技术条件.第1部分:概述

Technical delivery conditions for steel castings for pressure purposes. Part 1 : general.

NF A32-055-4:1996 压力用途的钢铸件的交货技术条件.第4部分:奥氏体和奥氏-铁素体钢的品位

Technical deliverry conditions for steel castings for pressure purposes. Part 4 : austenitic and austenitic-ferritic steel grades.

NF A32-055-3:1996 压力用途的钢铸件的交货技术条件.第3部分:低温下使用的钢的等级

Technical delivery conditions for steel castings for pressure purposes. Part 3 : steel grades for use at low temperatures.

STAS SR ISO 2605-3:1995 压力用途的钢铁产品．推导和验证的高温性能．第3部分：数据受限时得到高温屈服或证明应力特性的另一种程序

Prezenta parte a Standardului Interna?ional ISO 2605 stabile?te o variant? a metodei prezentate ?n ISO 2605/1 ?i ISO 2605/2, pentru deducerea limitei inferioare sau a limitei de curgere conven?ionale, la temperatura ridicat?, ?n cazul produselor de o?el pentru aplica?ii sub presiune. Standardul nu define?te ?i metoda de verificare, ?n cazul ?n care aceasta se solicit?, verificarea se efectueaz? prin ?ncercare la temperatur? ridicat? p?n? c?nd condi?iile din ISO 2605/1 ?i ISO 2605/2 sunt satisf?cute.

Steel products for pressure purposes - Derivation and verification of elevated temperature properties. Part 3: An alternative procedure for deriving the elevated temperature yield or proof stress properties when data are limited