77.140.65 钢丝、钢丝绳和环节链 标准查询与下载

T/CISA 041-2020 口罩用镀锌钢丝

本文件规定了口罩用镀锌钢丝产品的分类、标记、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书。

Galvanized steel wire for masks

T/CISA 042-2020 压水堆核电厂安全壳用预应力钢绞线

本文件规定了压水堆核电厂安全壳用预应力钢绞线的术语及定义、符号、代号及标记、订货内容、技术要求、试验方法、交货检验、包装、标识、运输、贮存及质量证明书。

Prestressed Steel Strand for Containment of Pressurized Water Reactor Nuclear Power Plant

ASTM A466/A466M-07(2020) 无焊接链条的标准规范

1.1 This specification covers weldless chain suitable for applications where a light and flexible chain is required. The material may be steel, brass, or bronze. 1.2 Seven classes of chain are covered: 1.2.1 Class SL—Single-loop chain. 1.2.2 Class DL—Double-loop chain. 1.2.3 Class SH—Sash chain. 1.2.4 Class SF—Plumbers’ chain. 1.2.5 Class SJ—Single-jack chain. 1.2.6 Class DJ—Double-jack chain. 1.2.7 Class RG—Register chain. 1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two system shall not be combined. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Weldless Chain

ASTM A555/A555M-20 不锈钢丝和盘条一般要求的标准规范

Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods

ASTM A510/A510M-20 碳钢用盘条和粗圆钢丝的一般要求的标准规范

1.1 This specification covers general requirements for carbon and alloy steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths. 1.2 In case of conflict, the requirements in the purchase order, on the drawing, in the individual specification, and in this general specification shall prevail in the sequence named. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, inch-pound units are shown in brackets. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel

MT/T 717-2019 煤矿重要用途在用钢丝绳性能测定方法及判定规则

Measurement methods and judgment rules for performance of steel wire ropes used for important purposes in coal mines

ASTM A603-19 金属涂层钢结构钢丝绳的标准规范

1.1 This specification covers metallic-coated steel structural wire rope, prestretched or nonprestretched for use where a high-strength, relatively flexible prefabricated metallic-coated multiple-wire tension member is desired as a component part of a structure. 1.2 The wire rope is furnished with Class A weight zinc or zinc-aluminum alloy-coated wires throughout. It can be furnished with Class B weight or Class C weight zinc-coated outer wires or Class B weight or Class C weight zinc-coated wires throughout as an option. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic-Coated Steel Structural Wire Rope

KS D 3554-2019 低碳钢线材

Low carbon steel wire rods

T/CISA 016-2019 绿色轮胎用19CCST钢帘线

本标准规定了绿色轮胎用19CCST（结构为0.25+18x0.225CCST）钢帘线的要求、试验方法、检验规则、标志、包装、运输、贮存及质量证明书等。

19CCST steel cord for green tire

ASTM F1911-05(2019) 带刺胶带安装的标准实施规程

1.1 This practice covers the installation procedure for barbed tape. 1.2 The primary purpose of this practice is to guide those responsible for or concerned with the installation of barbed tape on chain link fences, masonry walls, roofs or used as ground barriers. This standard is not intended to cover aspects of perimeter security for establishing levels of product performance or give analysis relating to various design comparisons. 1.3 This standard involves the use of material, that may cause injury, including exposure to hazardous materials, and operation of specialized equipment. 1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Installation of Barbed Tape

ASTM B227-15(2019) 硬拉铜包钢线标准规范

1.1 This specification covers bare hard-drawn round copperclad steel wire for electrical purposes (Note 1). NOTE 1—Wire ordered to this specification is not intended for redrawing. If wire is desired for this purpose, consult the manufacturer. 1.2 Four grades of wire are specified, designated as follows (Note 2): Grade 40 HS, Grade 40 EHS, Grade 30 HS, and Grade 30 EHS. NOTE 2—The grades covered by this specification correspond to the following commercial designations: Grade 40 HS, High Strength, 40 % Conductivity. Grade 40 EHS, Extra High Strength, 40 % Conductivity Grade 30 HS, High Strength, 30 % Conductivity. Grade 30 EHS, Extra High Strength, 30 % Conductivity. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Hard-Drawn Copper-Clad Steel Wire

ASTM A640-97(2019) 图8电缆用于信使支撑的镀锌钢绞线标准规范

1.1 This specification covers two sizes of extra-highstrength grade of concentric-lay steel wire strand, composed of seven, zinc-coated steel wires, specifically intended for use as the supporting messenger in Figure 8-type communication and electrical cables. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc-Coated Steel Strand for Messenger Support of Figure 8 Cable

ASTM A905-19 压力容器绕组用钢丝的标准规范

1.1 This specification covers requirements for a high strength drawn and cold rolled steel wire in two strength classes, with rectangular cross section, and round mill edge. This wire is intended for prestressed vessel and press frame windings. 1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text and tables, the SI units are shown in parentheses. The values stated in each system are not exact equivalents. Therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Wire, Pressure Vessel Winding

ASTM A641/A641M-19 锌的标准规范&x2013；涂层（镀锌）碳钢丝

1.1 This specification covers soft, medium, and hard temper zinc-coated (galvanized) carbon steel wire in coils for general use. 1.2 The supplementary requirements of this specification cover zinc-coated weights [masses] for nails, staples, and wire from which nails and staples are cut and formed. 1.3 This specification is applicable to orders in either inch-pound units (as A641) or SI units (as A641M). Values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in the two systems are not exact equivalents; therefore, each system shall be used independent of the other, without combining values in any way. 1.4 This specification and some referenced specifications are expressed in both inch-pound and SI units. If the order specifies the applicable “M” specification designation, the product shall be furnished to SI units. 1.5 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc–Coated (Galvanized) Carbon Steel Wire

ASTM A853-19 通用碳素钢丝标准规范

1.1 This specification covers carbon steel wire, supplied in coils, for general use. It may be produced hard drawn, annealed in process, or annealed at finish size. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Wire, Carbon, for General Use

YB/T 4750-2019 锌-5%铝-镁合金镀层钢绞线

Zinc-5% aluminum-magnesium alloy coated steel strand

YB/T 4747-2019 防扭绳用钢丝绳

Wire rope for anti-twist rope

YB/T 4749-2019 工程机编钢丝网用锌-5%铝-镁合金镀层钢丝

Zinc-5% aluminum-magnesium alloy coated steel wire for engineering machine-woven steel mesh

YB/T 4748-2019 钢芯铝绞线用锌-5%铝-镁合金镀层钢丝

Zinc-5% aluminum-magnesium alloy coated steel wire for steel core aluminum stranded wire

DB13/T 5011-2019 钢丝（钢筋）焊接网通用技术要求

General technical requirements for steel wire (rebar) welded mesh