77.140.65 钢丝、钢丝绳和环节链 标准查询与下载

KS D 7063-2022 镀锌钢丝

Zinc-coated steel wires

22/30455581 DC BS EN 10264-3 钢丝及线材制品 绳索用钢丝 第 3 部分：用于高负荷应用的圆形和异形非合金钢丝

BS EN 10264-3. Steel wire and wire products. Steel wire for ropes. - Part 3. Round and shaped non alloyed steel wire for high duty applications

ASTM A1007-22 钢丝绳用碳钢钢丝的标准规范

1.1 This specification covers uncoated and metallic coated classes of round, cold-drawn, carbon steel wire for wire rope in five strength levels. This specification specifies: 1.1.1 Dimensional tolerances, 1.1.2 Mechanical characteristics, 1.1.3 Chemical composition requirements, 1.1.4 Coating requirements (if applicable), and 1.1.5 Packaging requirements. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Carbon Steel Wire for Wire Rope

ASTM A1096/A1096M-22 评定混凝土钢筋用凹痕或普通钢丝粘结性的标准试验方法

1.1 This test method describes procedures for evaluating bond of individual steel wire, indented or plain, for concrete reinforcement. The bond determined by this test method is stated as the tensile force needed to pull the wire through the cured mortar in a cylindrical steel casing. 1.2 The result of the test is the maximum tensile force measured on the loaded end of the wire recorded at a free-end slip less than or equal to 0.10 in. [2.5 mm]. 1.3 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Bond of Individual Steel Wire, Indented or Plain, for Concrete Reinforcement

GSO ISO 3108:2022 钢丝绳 试验方法 测量破断拉力的测定

ISO 3108:2017 specifies a method of tensile test to destruction for determining the actual breaking force of steel wire ropes as given in ISO 2408. It is also applicable for other ropes, unless the International Standard concerned specifically excludes its use, or gives another method.

Steel wire ropes — Test method — Determination of measured breaking force

GSO ISO 2408:2022 钢丝绳 要求

ISO 2408:2017 specifies requirements for the manufacture, testing, acceptance, packing, marking and issuing of a certificate of quality of wire ropes. It is applicable to round strand ropes and compacted strand ropes made from wires ropes that are uncoated (bright), zinc-coated or Zn-Al coated. It is not applicable to ropes for - mining purposes, - aircraft control, - aerial ropeways and funiculars, and - lifts.

Steel wire ropes — Requirements

T/SSEA 0184-2022 文教类包胶用镀锌钢丝

本文件规定了文教类包胶用镀锌钢丝的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、标志及质量证明书。 本文件适用于制造挂历圈、回形针等文教类PVC、PE包胶用公称直径1.20mm~2.50mm的镀锌圆钢丝。

Galvanized steel wire for culture and education

T/SSEA 0182-2022 清洁球用镀锌钢丝

本文件规定了清洁球用镀锌钢丝的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、运输、贮存、标志及质量证明书。 本文件适用于制造清洁球用公称直径0.7mm~1.2mm的镀锌圆钢丝。

Galvanized steel wire for cleaning ball

T/SSEA 0183-2022 金属饰品用镀锌钢丝

本文件规定了金属饰品用镀锌钢丝的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、运输、贮存、标志及质量证明书。 本文件适用于制造手镯、手链、项链、眼镜架、宠物链等金属饰品用公称直径0.40mm~5.50mm的镀锌钢丝。

Galvanized steel wire for metal ornaments

BS ISO 23717:2022 钢丝及线材制品 软管加固钢丝

1   Scope This document specifies the composition, dimensions and mechanical properties of steel wire with a high mass fraction of carbon, generally brass coated, for reinforcing high-pressure hoses. It is applicable to multiple parallel wires, braided or spirally wrapped for reinforcement in a rubber or synthetic hose that is made to withstand a relatively high bursting pressure.

Steel wire and wire products. Hose reinforcement wire

ASTM A121-22 金属涂层碳钢带刺铁丝的标准规范

1.1 This specification covers metallic-coated steel barbed wire, consisting of a strand of two wires. 1.2 The barbed wire is available with aluminum, zinc, and zinc-5 % aluminum-mischmetal alloy coatings, with a number of coating weights, in a number of different constructions (designs), and in two grades. Not all designs are available in all coating types. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The text of this specification references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

ASTM A854/A854M-08(2022) 金属涂层钢光滑高强度栅栏和网格线的标准规范

1.1 This specification covers 12 1⁄2-gage (0.099-in.) [2.5mm] Class 3 metallic-coated steel wire suitable for use in parallel–wire fence, trellis, and similar structures that are typically nonelectrified. Two types of coatings are covered, as follows: 1.1.1 Type 1—Zinc-coated (galvanized), and 1.1.2 Type II—Zinc-5 % aluminum mischmetal (Zn-5AlMM) alloy coated. 1.2 This specification is applicable to orders in either inch-pound units (as A854) or acceptable SI units (as A854M). Inch-pound units and SI units are not necessarily equivalent. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic-Coated Steel Smooth High-Tensile Fence and Trellis Wire

ASTM A116-22 金属涂层钢丝编织栅栏织物的标准规范

1.1 This specification covers metallic-coated steel fence fabric having a series of horizontal (line) wires, with vertical (stay) wires either wrapped around the line wire (hinge joint) or fixed with another separate wire to the line wire (continuous stay fixed knot joint), forming rectangular openings. The fence fabric is suitable for use in fences for farm field enclosure (to keep domestic animals in or out), for wildlife and exotic animal control, for highway or railroad right-of-way fencing (to control access), and other similar uses. 1.2 This specification covers fence fabric in various designs, tensile strength grades, and metallic coating types and grades. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic-Coated, Steel-Woven Wire Fence Fabric

ASTM A411-08(2022) 镀锌（镀锌）低碳钢铠装线标准规范

1.1 This specification covers zinc-coated low-carbon steel wire for use in armoring for protection against damage of submarine and underground cables used for communication, control, or power purposes. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor Wire

ISO 23717:2022 钢丝和钢丝制品.软管加强钢丝

This document specifies the composition, dimensions and mechanical properties of steel wire with a high mass fraction of carbon, generally brass coated, for reinforcing high-pressure hoses. It is applicable to multiple parallel wires, braided or spirally wrapped for reinforcement in a rubber or synthetic hose that is made to withstand a relatively high bursting pressure.

Steel wire and wire products — Hose reinforcement wire

ASTM E2948-22 实心圆细钢丝旋转弯曲疲劳试验的标准试验方法

1.1 This test method is intended as a procedure for the performance of rotating bending fatigue tests of solid round fine wire to obtain the fatigue strength of metallic materials at a specified life in the fatigue regime where the strains (stresses) are predominately and nominally linear elastic. This test method is limited to the fatigue testing of small diameter solid round wire subjected to a constant amplitude periodic strain (stress). The methodology can be useful in assessing the effects of internal material structure, such as inclusions, in melt technique and cold work processing studies. However, there is a caveat. The strain, due to the radial strain gradient imposed by the test methodology, is a maximum at the surface and zero at the centerline. Thus the test method may not seek out the “weakest link,” largest inclusions, that govern uniaxial high cycle fatigue life where the strain is uniform across the cross section and where fatigue damage initiates at a subsurface location (1-5).2 Also, pre-strain, which can influence fatigue life, is not included in this test method. NOTE 1—The following documents, although not specifically mentioned, are considered sufficiently important to be listed in this test method: ASTM STP 566 Handbook of Fatigue Testing ASTM STP 588 Manual on Statistical Planning and Analysis for Fatigue Experiments ASTM STP 731 Tables for Estimating Median Fatigue Limits (6-8) 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Conducting Rotating Bending Fatigue Tests of Solid Round Fine Wire

DIN EN 12385-5:2022 钢丝绳 安全 第5部分：电梯用绞合绳；德文版 EN 12385-5:2021 + AC:2021

This document specifies the particular materials, manufacturing and testing requirements for stranded ropes for suspension, compensating and governor duties for traction drive and hydraulic lifts moving between guides and similar applications. The particular hazards covered by th

Steel wire ropes - Safety - Part 5: Stranded ropes for lifts; German version EN 12385-5:2021 + AC:2021

T/ZZXJX 079-2021 钢丝绳网片面层加固技术施工及验收规程

1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本规定　 5 施工准备　   5.1 材料　   5.2 机具　   5.3 作业条件　 6 施工　   6.1 清理、修整原结构及构件　   6.2 界面胶施工　   6.3 钢丝绳网片安装　   6.4 聚合物砂浆施工。 7 成品保护要求　 8 季节性施工要求　 9 安全环保措施　   9.1 安全操作要求　   9.2 环保措施　 10 分项工程质量检查与验收　   10.1 基本规定　   10.2 钢丝绳网片分项工程　   10.3 聚合物砂浆分项工程　   10.4 检验批的划分　

Construction and acceptance regulations of one-piece surface layer reinforcement technology of steel wire rope mesh

T/CISA 180-2021 打结刀用钢丝

本文件规定了打结刀用钢丝的标记、订货内容、尺寸、外形及允许偏差、技术要求、试验方法、检验规则、数值修约、包装、标志及质量证明书。?本文件适用于打结刀用钢丝

Steel wire for knotting knife

T/CISA 179-2021 波形弹性垫圈用钢丝

本文件规定了波形弹性垫圈用钢丝的标记、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、数值修约、包装、标志及质量证明书。?本文件适用于波形弹性垫圈用钢丝的制造

Steel wire for wave elastic washers