77.140.80 钢铁铸件 标准查询与下载

ASTM A48/A48M-22 灰铸铁件标准规范

1.1 This specification covers gray iron castings intended for general engineering use where tensile strength is a major consideration. Castings are classified on the basis of the tensile strength of the iron in separately cast test bars. 1.1.1 This specification subordinates chemical composition to tensile strength. 1.2 Castings produced to this specification are graded on the basis of minimum tensile strength obtained in special test coupons designed to standardize cooling rate. The tensile strength developed in certain casting sections may vary from test coupon values (see X1.2). 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Gray Iron Castings

ASTM A217/A217M-22 高温设备用承压部件用马氏体不锈钢和合金钢铸件的标准规范

1.1 This specification2 covers martensitic stainless steel and alloy steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1) intended primarily for high-temperature and corrosive service (Note 2). 1.2 One grade of martensitic stainless steel and nine grades of ferritic alloy steel are covered. Selection will depend on design and service conditions, mechanical properties, and the high-temperature and corrosion-resistant characteristics (Note 3). NOTE 1—Carbon steel castings for pressure-containing parts are covered by Specification A216/A216M. Low alloy quench-and-tempered grades equivalent to Specification A217/A217M grades may be found in both Specifications A352/A352M and A487/A487M. NOTE 2—The grades covered by this specification represent materials that are generally suitable for assembly with other castings or wrought steel parts by fusion welding. It is not intended to imply that these grades possess equal degrees of weldability; therefore, it is the responsibility of the purchaser to establish for himself a suitable welding technique. Since these grades possess varying degrees of suitability for high-temperature and corrosion-resistant service, it is also the responsibility of the purchaser to determine which grade shall be furnished, due consideration being given to the requirements of the applicable construction codes. NOTE 3—The committee formulating this specification has included nine grades of materials that are considered to represent basic types of ferritic alloy steels suitable for valves, flanges, fittings, and other pressurecontaining parts. Additional alloy steels that may better fulfill certain types of service will be considered for inclusion in this specification by the committee as the need becomes apparent. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service

ASTM A327/A327M-22 铸铁冲击试验的标准试验方法

1.1 These test methods for impact testing cover the details of apparatus, test specimens, and procedures for cast iron, including gray iron, white iron, malleable iron, ductile iron, and austempered ductile iron, but not including chilled rolls or rolls with white iron skins. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Impact Testing of Cast Irons

ASTM A367-22 铸铁冷激试验的标准试验方法

1.1 These test methods for chill testing apply to gray irons that are to be free of chill in the casting and to chilled irons that are to have a specific depth of chill in the casting. Two test methods for determining the chilling tendencies of cast iron are covered as follows. For many applications, either test method will be satisfactory if test pieces of the proper dimensions are selected. 1.1.1 Test Method A, Wedge Test—This test is adapted for the higher-strength gray irons. The accelerated cooling rate to induce the formation of a chill is brought about through the design of the test specimen. This test method is simpler than Test Method B since maintenance of chill blocks or plates is not necessary. 1.1.2 Test Method B, Chill Test—This test is adapted for the softer grades of gray iron and should be used if the casting is to have a specified depth of chill. The chill in this type of test is induced by casting one edge of the test specimen against a metal or graphite chilled plate or block. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered to be part of the standard. 1.2.1 The metric equivalency charts in Figs. 1 and 2 are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. TEST METHOD A – WEDGE TEST

Standard Test Methods for Chill Testing of Cast Iron

ASTM A744/A744M-21a 严酷环境用耐腐蚀铁铬镍铸件的标准规范

1.1 This specification covers iron-chromium-nickel alloy stainless steel castings intended for particularly severe corrosive applications. 1.2 This specification requires post-weld heat treatment of all weld repairs affecting surfaces intended to be wetted by the corrosive medium. For applications for which post-weld heat treatment is not considered mandatory for retention of acceptable corrosion resistance, refer to Specification A743/A743M. NOTE 1—For general corrosion-resistant alloy castings, reference should be made to Specification A743/A743M. For general heat-resistant alloy castings, reference should be made to Specification A297/A297M. For nickel-base alloy castings, refer to Specification A494/A494M. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3.1 Within the text, the SI units are shown in brackets. 1.3.2 Inch-pound units are applicable for material ordered to Specification A744 and SI units for material ordered to Specification A744M. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service

T/CSTM 00646.1-2021 金属材料 销-盘摩擦磨损试验 第1部分：室温摩擦磨损试验方法

本文件规定了金属材料在室温条件下销-盘摩擦磨损试验的术语及定义、试验原理、试样、试验设备及仪器、试验方法、试验结果处理及试验报告。 本文件适用于金属及其复合材料在室温条件下销-盘滑动摩擦条件下磨损量及摩擦系数的测定。

Ｍetal materials－Friction and wear testing with a pin-on-disk apparatus － Part 1: Friction and wear testing at ambient temperature

T/CSTM 00646.2-2021 金属材料 销-盘摩擦磨损试验 第2部分：高温摩擦磨损试验方法

本文件规定了金属材料在温度高于室温条件下销-盘摩擦磨损试验的术语及定义、试验原理、试样、试验设备及仪器、实验方法、试验结果处理及试验报告。 本文件适用于金属及其复合材料在辅助热源加热下温度高于室温条件下销-盘滑动摩擦条件下磨损量及摩擦系数的测定。

Metal materials_—Friction and wear testing with a pin-on-disk apparatus — Part 2: Friction and wear testing at high-temperature

PN-EN 10283-2019-11 P 耐蚀钢铸件

Corrosion resistant steel castings

ASTM A48/A48M-03(2021) 灰铸铁件标准规范

Standard Specification for Gray Iron Castings

ASTM A216/A216M-21 高温设备用熔焊用碳素钢铸件的标准规范

1.1?This specification2 covers carbon steel castings for valves, flanges, fittings, or other pressure-containing parts for high-temperature service and of quality suitable for assembly with other castings or wrought steel parts by fusion welding. 1.2?Three grades, WCA, WCB, and

Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service

ASTM A297/A297M-21a 一般用途耐热铁铬和铁铬镍铸钢件的标准规范

1.1 This specification covers iron-chromium and ironchromium-nickel alloy castings for heat-resistant service. The grades covered by this specification are general purpose alloys and no attempt has been made to include heat-resisting alloys used for special production application. NOTE 1—For heat-resisting alloys used for special product application, reference should be made to Specifications A351/A351M, A217/A217M, and A447/A447M. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application

KS D 4114-2021 通用铬钼钢锻件

Chromium molybdenum steel forgings for general use

BS ISO 14737:2021 一般用途的碳素和低合金铸钢

Carbon and low alloy cast steels for general applications

T/SXZX 005-2021 大型矿用挖掘机高锰钢履带板 技术规范

本文件规定了大型矿用机械式挖掘机用高锰钢材质重型履带板铸件（简称履带板铸件）的术语和定义、制造工艺、技术要求、检验规则与试验方法、质量证明书、铸件标志、涂装、包装和贮运。

High manganese steel track pads for large mining excavators －Technical specification

T/SXZX 006-2021 大型矿用挖掘机合金钢履带板 技术规范

本文件规定了大型矿用液压挖掘机用合金钢材质重型履带板（简称履带板）铸件的术语和定义、制造工艺、技术要求、检验规则与试验方法、质量证明书、铸件标志、涂装、包装和贮运。

Alloy steel track pads for large mining excavators －Technical specification

GSO ASTM E903:2021 使用积分球测量材料的太阳光吸收率、反射率和透射率的标准测试方法

-

Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres

ISO 14737:2021 一般应用碳素和低合金铸钢

This document specifies requirements for carbon and low alloy cast steel grades for general applications. NOTE 1 Annex A provides guidance on welding. NOTE 2 Annex B gives information on ISO grade designation and available UNS numbers which are similar to the ISO grade designation.

Carbon and low alloy cast steels for general applications

T/SXZX 004-2021 铁型覆砂球墨铸铁盘式制动器用铸件

本文件规定了采用铁型覆砂工艺铸造的球墨铸铁盘式制动器用铸件（以下简称铸件）的技术要求，试验方法，检验规则，标志、标签和随行文件，包装、运输和贮存。

Spheroidal graphite cast iron Disk brake castings produced with sand-lined metal mould

ASTM E1030/E1030M-21 金属铸件射线照相检验的标准实施规程

1.1?This practice2 provides a uniform procedure for radiographic examination of metallic castings using radiographic film as the recording medium. 1.2?This standard addresses the achievement of, or protocols for achieving, common or practical levels of radiographic coverage for

Standard Practice for Radiographic Examination of Metallic Castings

KS D 3710-2021 一般用途碳素钢锻件

Carbon steel forgings for general use