77.150.40 镍和铬产品 标准查询与下载
共找到 397 条与 镍和铬产品 相关的标准，共 27 页
1.1 This specification2 covers plate, sheet, and strip of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06455, N06035, UNS N06058, UNS N06059),3 low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), low-carbon nickel-molybdenum-chromium (UNS N10362), low-carbon nickel-chromium-molybdenum-tantalum alloy (UNS N06210), and low-carbon nickel-chromium-molybdenum-tungsten alloy (UNS N06686) as shown in Table 1, for use in general corrosive service. (A) Shall be determined arithmetically by difference. †Editorially corrected. (A) D refers to the diameter of the tension specimen.(B) Hardness values are shown for information purposes only and are not to be used as a basis of acceptance or rejection. For approximate hardness conversions, see Hardness Conversion Tables E140. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip—Hot or cold rolled, solution annealed, and descaled unless solution anneal is performed in an atmosphere yielding a bright finish. 1.2.2 Plate—Hot or cold rolled, solution annealed, and descaled. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium
- ICS
- 77.150.40
- CCS
- H62
- 发布
- 2015
- 实施
Manganese nickel wire. Specifications
- ICS
- 77.150.40
- CCS
- H62
- 发布
- 2015
- 实施
- 2016-04-01
1.1 This specification covers additively manufactured UNS N06625 components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured UNS N06625 components for defining the requirements and ensuring component properties. 1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Supplementary Requirements S1–S16. 1.5 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Additive Manufacturing Nickel Alloy &40;UNS N06625&41; with Powder Bed Fusion
- ICS
- 77.150.40
- CCS
- 发布
- 2014
- 实施
1.1 This specification covers nickel, nickel-copper, nickel-copper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium alloy castings for corrosion-resistant service. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Standard Specification for Castings, Nickel and Nickel Alloy
- ICS
- 77.150.40
- CCS
- H43;J32
- 发布
- 2014
- 实施
1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating purposes, of alloys having the nominal compositions of 808201;% nickel and 208201;% chromium; 608201;% nickel, 168201;% chromium, and remainder iron; and 358201;% nickel, 208201;% chromium, and remainder iron; 388201;% nickel, 218201;% chromium, and remainder iron; and 358201;% nickel, 208201;% chromium remainder iron. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Standard Specification for Drawn or Rolled Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating Elements
- ICS
- 77.150.40
- CCS
- 发布
- 2014
- 实施
Nickel and copper-nickel alloys wire for extension leads for thermoelectric temperature transducers. Specifications
- ICS
- 77.150.40
- CCS
- 发布
- 2014
- 实施
- 2015-09-01
1.1 This specification covers additively manufactured UNS N07718 components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured UNS N07718 components for defining the requirements and ensuring component properties. 1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Supplementary Requirements S1–S16. 1.5 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion
- ICS
- 77.150.40
- CCS
- 发布
- 2014
- 实施
1.1 This specification covers additively manufactured UNS N07718 components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured UNS N07718 components for defining the requirements and ensuring component properties. 1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Supplementary Requirements S1–S16. 1.5 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion
- ICS
- 77.150.40
- CCS
- 发布
- 2014
- 实施
This International Standard specifies requirements for nickel and nickel alloy castings. The grades covered represent types of alloys suitable for a broad range of application in a wide variety of corrosive and high temperature environments
Nickel and nickel alloy castings
- ICS
- 77.150.40
- CCS
- 发布
- 2013-12-31
- 实施
Nickel and nickel alloy plate, sheet and strip
- ICS
- 77.150.40
- CCS
- 发布
- 2013-12-30
- 实施
Nickel and nickel alloys－Composition and form of wrought products
- ICS
- 77.150.40
- CCS
- 发布
- 2013-12-30
- 实施
本标准规定了集成电路器件用镍钒合金溅射靶材的要求、试验方法、检验规则和标志、包装、运输、贮存、质量证明书及合同或订货单内容。本标准适用于电子薄膜制造用的各类镍钒合金溅射靶材。
Sputtering nickel vanadium alloy target used in integrated circuit device
- ICS
- 77.150.40
- CCS
- H62
- 发布
- 2013-10-17
- 实施
- 2014-03-01
本标准规定了还原镍粉的要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书和合同(或订货单)内容。本标准适用于草酸镍、碳酸镍和氧化镍等含镍物料经还原得到的镍粉,供硬质合金、金刚石制品、粉末冶金及充电电池等行业使用。
Deoxidization nickle powder
- ICS
- 77.150.40
- CCS
- H13
- 发布
- 2013-10-17
- 实施
- 2014-03-01
本标准规定了电真空器件用镍及镍合金板带材和棒材的要求、试验方法、检验规则和包装、标志、运输、贮存及质量证明书和合同(或订货单)等内容。本标准适用于电子工业部门制作氧化物阴极用的镍及镍合金板带材和棒材。
Nickel and nickel alloy sheet, strip and rods for vacuum electron devices
- ICS
- 77.150.40
- CCS
- H62
- 发布
- 2013-10-17
- 实施
- 2014-03-01
本标准规定了采用红土镍矿为原料火法生产的冶炼镍基体料技术要求、试验方法、检验规则、包装、标志、运输、贮存和质量证明书等。 本标准适用于冶炼不锈钢、冶炼特钢、铸造特殊铸件用镍基体料及镍合金的替代品。
The dominated smelting nickel substrate material
- ICS
- 77.150.40
- CCS
- H60
- 发布
- 2013-05-02
- 实施
- 2013-09-01
