77.150.40 镍和铬产品 标准查询与下载

ASTM B168-19e1 镍铬铝合金（UNS N06699）、镍铬铁合金（UNS N06600、N06601、N06603、N06690、N06693、N06025、N06045和N06696）、镍铬钴钼合金（UNS N06617）、镍铁铬钨合金（UNS N06674）和镍铬钼铜合金（UNS N06235）板材、薄板、 剥去

1.1 This specification2 covers rolled nickel-chromiumaluminum alloys (UNS N06699), nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696),3 nickel-chromium-cobalt-molybdenum alloy (UNS N06617), nickel-iron-chromium-tungsten alloy (UNS N06674), and nickel-chromium-molybdenum-copper alloy (UNS N06235) plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Mo

ASTM B668-14(2019) UNS N08028和N08029无缝管的标准规范

1.1 This specification covers UNS N08028 and N08029 seamless cold-finished or hot-finished pipe and tube intended for general corrosive service. The general requirements are covered in Specification B829. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for UNS N08028 and N08029 Seamless Pipe and Tube

ASTM B751-19 镍和镍合金焊接管一般要求的标准规范

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Tube

ASTM B775/B775M-19 镍和镍合金焊接管一般要求的标准规范

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe

ASTM B906-19 平轧镍和镍合金板、薄板和带材的一般要求的标准规范

Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip

ASTM B558-79(2019) 电镀用镍合金制备的标准实施规程

1.1 This practice is intended to serve as a guide for producing adherent electrodeposits of nickel on nickel alloys. Only those methods that are well known and generally practiced are included. Methods that have been used successfully but not on a broad scale are not included. Once nickel is applied, other metals may be electroplated on the product. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Nickel Alloys for Electroplating

ASTM B162-99(2019) 镍板薄板和带材的标准规范

1.1 This specification2 covers rolled nickel (UNS N02200) and low-carbon nickel (UNS N02201)3 plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel Plate, Sheet, and Strip

ASTM B514-05(2019) 焊接镍铁铬合金管的标准规范

1.1 This specification2 covers nickel-iron-chromium alloys in the form of welded, cold-worked, and annealed pipe for general corrosive service and heat-resisting applications. These products are furnished in three alloys: UNS N08120, UNS N08800, and UNS N08810.3 Alloy UNS N08800 is employed normally in service temperatures up to and including 1100 °F (593 °C). Alloys UNS N08120 and UNS N08810 are employed normally in service temperatures above 1100 °F where resistance to creep and rupture is required, and are annealed to develop controlled grain size for optimum properties in this temperature range. 1.2 This specification covers outside diameter and nominal wall pipe shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of the specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Nickel-Iron-Chromium Alloy Pipe

ASTM B161-05(2019) 镍无缝管的标准规范

1.1 This specification2 covers nickel (UNS N02200)3 and low-carbon nickel (UNS N02201)3 in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table X1.1. 1.1.1 Hot-worked material is available. Properties are to be agreed upon between the manufacturer and purchaser. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel Seamless Pipe and Tube

ASTM B166-19 镍铬铝合金、镍铬铁合金、镍铬钴钼合金、镍铁铬钨合金和镍铬钼铜合金棒、棒和线材的标准规范

1.1 This specification2 covers nickel-chromium-aluminum alloy, nickel-chromium-iron alloys,3 nickel-chromium-cobaltmolybdenum alloy, nickel-iron-chromium-tungsten alloy, and nickel-chromim-molybdenum-copper alloy in the form of hotfinished and cold-worked rounds, squares, hexagons, rectangles, and cold-worked wire. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Aluminum Alloy, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Cop

ASTM B446-19 镍铬钼铌合金（UNS N06625）、镍铬钼硅合金（UNS N06219）和镍铬钼钨合金（UNS N06650）棒和棒的标准规范

1.1 This specification covers nickel-chromiummolybdenum-columbium (UNS N06625), nickel-chromiummolybdenum-silicon alloy (UNS N06219), and NickelChromium-Molybdenum-Tungsten Alloy (UNS N06650)2 in the form of hot-worked rod and bar and cold-worked rod in the conditions shown in Table 1. 1.1.1 UNS N06625 products are furnished in two grades of different heat-treated conditions: 1.1.1.1 Grade 1 (Annealed)—Material is normally employed in service temperatures up to 1100°F (593°C). 1.1.1.2 Grade 2 (Solution Annealed)—Material is normally employed in service temperatures above 1100°F (593°C) when resistance to creep and rupture is required. NOTE 1—Hot-working or reannealing may change properties significantly, depending on working history and temperatures. 1.1.2 Alloys UNS N06219 and UNS N06650 are supplied in solution annealed condition only. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: cThis standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Ro

ASTM B474/B474M-19 电熔焊接镍和镍合金管标准规范

1.1 This specification covers electric fusion welded pipe suitable for high-temperature or corrosive service as listed in Table 1. (Although no restrictions are placed on the sizes of pipe that may be furnished under this specification, commercial practice is commonly limited to sizes not less than 8 in. [203 mm] nominal diameter.) 1.2 Five classes of pipe are covered as follows: 1.2.1 Class 1—Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed. 1.2.2 Class 2—Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required. 1.2.3 Class 3—Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed. 1.2.4 Class 4—Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal. 1.2.5 Class 5—Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe

ASTM B536-19 镍铁铬硅合金板、薄板和带材的标准规范

1.1 This specification covers nickel-iron-chromium silicon alloys (UNS N08330 and UNS N08332)2 plate, sheet, and strip intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Silicon Alloys Plate, Sheet, and Strip

ASTM B164-03(2019) 镍铜合金棒、棒和线的标准规范

1.1 This specification2 covers nickel-copper alloys UNS N04400 and N044053 in the form of hot-worked and coldworked rod and bar in the conditions shown in Table 1 and cold-worked wire in the conditions shown in Table 2. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire

ISO 23163:2019 镍和镍合金.精镍.取样

This document specifies sampling procedures for up to 25 tonnes (metric tons) of refined nickel of the same composition, size and shape and manufactured under similar conditions of production.

Nickel and nickel alloys — Refined nickel — Sampling

ISO 12725:2019 镍和镍合金铸件

This document specifies requirements for nickel and nickel alloy castings. The grades specified represent types of alloys suitable for a broad range of application in a wide variety of corrosive and high temperature environments.

Nickel and nickel alloy castings

T/CNIA 0006-2019 冶炼副产品 硫酸镍

本标准规定了冶炼副产品硫酸镍的技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书以及订货单（或合同）内容。 本标准适用于铜冶炼电解精炼的电解液经脱铜、除杂后结晶形成的硫酸镍，产品主要供镍工业原料使用。

Smelting by-product nickel sulfate

ASTM B127-19 薄板和带材用镍铜合金（UNS N04400）板的标准规范

1.1 This specification2 covers rolled nickel-copper alloy (UNS N04400)3 plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip

ASTM B167-18 镍铬铝合金（UNS N06699）、镍铬铁合金（UNS N06600、N06601、N06603、N06690、N06693、N06025、N06045和N06696）、镍铬钴钼合金（UNS N06617）、镍铁铬钨合金（UNS N06674）的标准规范 和镍铬钼铜合金（UNS N06235）无缝管

1.1 This specification2 covers nickel-chromium-aluminum alloys (UNS N06699), nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696),3 nickel-chromium-cobalt-molybdenum alloy (UNS N06617), nickel-iron-chromium-tungsten alloy (UNS N06674), and nickel-chromium-molybdenum-copper alloy (UNS N06235) in cold-worked annealed, hot-worked annealed, and hot-finished seamless pipe and tube intended for general corrosion resistant and heat resistant applications. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Mo

ASTM B166-18 镍铬铁合金（UNS N06600、N06601、N06603、N06690、N06693、N06025、N06045和N06696）、镍铬钴钼合金（UNS N06617）、镍铁铬钨合金（UNS N06674）和镍铬钼铜合金（UNS N06235）棒材、棒材和线材的标准规范

Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), Nickel-Iron-Chrom